[PATCH 1/3] mfd: add STMPE811 core support

From: Luotao Fu
Date: Fri Jun 11 2010 - 06:14:29 EST


STMPE811 is a multifunction device, which contains a GPIO controller, a
Touchscreen controller, an ADC and a temperature sensor. This patch adds a core
driver for this device. The driver provides core functionalities like accessing
the registers and management of subdevices. The device supports communication
through SPI and I2C interface. Currently we only support I2C.

Signed-off-by: Luotao Fu <l.fu@xxxxxxxxxxxxxx>
---
drivers/mfd/Kconfig | 8 +
drivers/mfd/Makefile | 1 +
drivers/mfd/stmpe811-core.c | 369 ++++++++++++++++++++++++++++++++++++++++++
include/linux/mfd/stmpe811.h | 126 ++++++++++++++
4 files changed, 504 insertions(+), 0 deletions(-)
create mode 100644 drivers/mfd/stmpe811-core.c
create mode 100644 include/linux/mfd/stmpe811.h

diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 9da0e50..2c5388b 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -482,6 +482,14 @@ config MFD_JANZ_CMODIO
host many different types of MODULbus daughterboards, including
CAN and GPIO controllers.

+config MFD_STMPE811
+ tristate "STMicroelectronics STMPE811"
+ depends on I2C
+ select MFD_CORE
+ help
+ This is the core driver for the stmpe811 GPIO expander with touchscreen
+ controller, ADC and temperature sensor.
+
endif # MFD_SUPPORT

menu "Multimedia Capabilities Port drivers"
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index fb503e7..6a7ad83 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -71,3 +71,4 @@ obj-$(CONFIG_PMIC_ADP5520) += adp5520.o
obj-$(CONFIG_LPC_SCH) += lpc_sch.o
obj-$(CONFIG_MFD_RDC321X) += rdc321x-southbridge.o
obj-$(CONFIG_MFD_JANZ_CMODIO) += janz-cmodio.o
+obj-$(CONFIG_MFD_STMPE811) += stmpe811-core.o
diff --git a/drivers/mfd/stmpe811-core.c b/drivers/mfd/stmpe811-core.c
new file mode 100644
index 0000000..080b3d7
--- /dev/null
+++ b/drivers/mfd/stmpe811-core.c
@@ -0,0 +1,369 @@
+/*
+ * stmpe811-core.c -- core support for STMicroelectronics STMPE811 chip.
+ *
+ * based on pcf50633-core.c by Harald Welte <laforge@xxxxxxxxxxxx> and
+ * Balaji Rao <balajirrao@xxxxxxxxxxxx>
+ *
+ * (c)2010 Luotao Fu <l.fu@xxxxxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/i2c.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/stmpe811.h>
+
+static inline int __stmpe811_i2c_reads(struct i2c_client *client, int reg,
+ int len, u8 *val)
+{
+ int ret;
+
+ ret = i2c_smbus_read_i2c_block_data(client, reg, len, val);
+ if (ret < 0) {
+ dev_err(&client->dev, "failed reading from 0x%02x\n", reg);
+ return ret;
+ }
+ return 0;
+}
+
+static struct mfd_cell stmpe811_ts_dev = {
+ .name = "stmpe811-ts",
+};
+
+static struct mfd_cell stmpe811_gpio_dev = {
+ .name = "stmpe811-gpio",
+};
+
+static void stmpe811_irq_worker(struct work_struct *work)
+{
+ struct stmpe811 *stm;
+ int ret, bit;
+ u8 int_stat;
+ irq_handler_t handler;
+ void *data;
+
+ stm = container_of(work, struct stmpe811, irq_work);
+
+ ret = stmpe811_reg_read(stm, STMPE811_REG_INT_STA, &int_stat);
+ if (ret) {
+ dev_err(stm->dev, "Error reading INT registers\n");
+ goto out;
+ }
+
+ dev_dbg(stm->dev, "%s int_stat 0x%02x\n", __func__, int_stat);
+
+ for_each_set_bit(bit, (unsigned long *)&int_stat, STMPE811_NUM_IRQ) {
+ handler = stm->irqhandler[bit];
+ data = stm->irqdata[bit];
+ if (handler) {
+ /* mask the interrupt while calling handler */
+ stmpe811_reg_clear_bits(stm, STMPE811_REG_INT_EN,
+ 1 << bit);
+ /* call handler and acknowledge the interrupt */
+ handler(bit, data);
+ stmpe811_reg_set_bits(stm, STMPE811_REG_INT_STA,
+ (1 << bit));
+ /* demask the interrupt */
+ stmpe811_reg_set_bits(stm, STMPE811_REG_INT_EN,
+ 1 << bit);
+ }
+ }
+out:
+ put_device(stm->dev);
+ enable_irq(stm->irq);
+
+}
+
+static irqreturn_t stmpe811_irq(int irq, void *data)
+{
+ struct stmpe811 *stm = data;
+
+ get_device(stm->dev);
+ disable_irq_nosync(stm->irq);
+ queue_work(stm->work_queue, &stm->irq_work);
+
+ return IRQ_HANDLED;
+}
+
+static inline int __stmpe811_i2c_read(struct i2c_client *client,
+ int reg, u8 *val)
+{
+ int ret;
+
+ ret = i2c_smbus_read_byte_data(client, reg);
+ if (ret < 0) {
+ dev_err(&client->dev, "failed reading at 0x%02x\n", reg);
+ return ret;
+ }
+ dev_dbg(&client->dev, "%s: value 0x%x from 0x%x\n", __func__, ret, reg);
+
+ *val = (u8) ret;
+ return 0;
+}
+
+static inline int __stmpe811_i2c_write(struct i2c_client *client,
+ int reg, u8 val)
+{
+ int ret;
+
+ ret = i2c_smbus_write_byte_data(client, reg, val);
+ if (ret < 0) {
+ dev_err(&client->dev, "failed writing 0x%02x to 0x%02x\n",
+ val, reg);
+ return ret;
+ }
+ return 0;
+}
+
+int stmpe811_block_read(struct stmpe811 *stm, u8 reg, uint len, u8 *val)
+{
+ int ret;
+
+ mutex_lock(&stm->io_lock);
+ ret = __stmpe811_i2c_reads(stm->i2c_client, reg, len, val);
+ mutex_unlock(&stm->io_lock);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(stmpe811_block_read);
+
+int stmpe811_reg_read(struct stmpe811 *stm, u8 reg, u8 *val)
+{
+ int ret;
+
+ mutex_lock(&stm->io_lock);
+ ret = __stmpe811_i2c_read(stm->i2c_client, reg, val);
+ mutex_unlock(&stm->io_lock);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(stmpe811_reg_read);
+
+int stmpe811_reg_write(struct stmpe811 *stm, u8 reg, u8 val)
+{
+ int ret;
+
+ mutex_lock(&stm->io_lock);
+ ret = __stmpe811_i2c_write(stm->i2c_client, reg, val);
+ mutex_unlock(&stm->io_lock);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(stmpe811_reg_write);
+
+int stmpe811_reg_set_bits(struct stmpe811 *stm, u8 reg, u8 val)
+{
+ int ret;
+ u8 tmp;
+
+ mutex_lock(&stm->io_lock);
+ ret = __stmpe811_i2c_read(stm->i2c_client, reg, &tmp);
+ if (ret < 0)
+ goto out;
+
+ tmp |= val;
+ ret = __stmpe811_i2c_write(stm->i2c_client, reg, tmp);
+
+out:
+ mutex_unlock(&stm->io_lock);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(stmpe811_reg_set_bits);
+
+int stmpe811_reg_clear_bits(struct stmpe811 *stm, u8 reg, u8 val)
+{
+ int ret;
+ u8 tmp;
+
+ mutex_lock(&stm->io_lock);
+ ret = __stmpe811_i2c_read(stm->i2c_client, reg, &tmp);
+ if (ret < 0)
+ goto out;
+
+ tmp &= ~val;
+ ret = __stmpe811_i2c_write(stm->i2c_client, reg, tmp);
+
+out:
+ mutex_unlock(&stm->io_lock);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(stmpe811_reg_clear_bits);
+
+int stmpe811_register_irq(struct stmpe811 *stm, int irq,
+ irq_handler_t handler, void *data)
+{
+ if (irq < 0 || irq > STMPE811_NUM_IRQ || !handler)
+ return -EINVAL;
+
+ if (WARN_ON(stm->irqhandler[irq]))
+ return -EBUSY;
+
+ stm->irqhandler[irq] = handler;
+ stm->irqdata[irq] = data;
+ /* unmask the irq */
+ return stmpe811_reg_set_bits(stm, STMPE811_REG_INT_EN, 1 << irq);
+}
+EXPORT_SYMBOL_GPL(stmpe811_register_irq);
+
+int stmpe811_free_irq(struct stmpe811 *stm, int irq)
+{
+ if (irq < 0 || irq > STMPE811_NUM_IRQ)
+ return -EINVAL;
+
+ stm->irqhandler[irq] = NULL;
+
+ return stmpe811_reg_clear_bits(stm, STMPE811_REG_INT_EN, 1 << irq);
+}
+EXPORT_SYMBOL_GPL(stmpe811_free_irq);
+
+static int __devinit stmpe811_probe(struct i2c_client *client,
+ const struct i2c_device_id *ids)
+{
+ struct stmpe811 *stm;
+ struct stmpe811_platform_data *pdata = client->dev.platform_data;
+ int ret = 0;
+ u8 chip_id[2], chip_ver = 0;
+
+ if (!client->irq) {
+ dev_err(&client->dev, "Missing IRQ\n");
+ return -ENOENT;
+ }
+
+ stm = kzalloc(sizeof(*stm), GFP_KERNEL);
+ if (!stm)
+ return -ENOMEM;
+
+ stm->pdata = pdata;
+
+ mutex_init(&stm->io_lock);
+
+ i2c_set_clientdata(client, stm);
+ stm->dev = &client->dev;
+ stm->i2c_client = client;
+ stm->irq = client->irq;
+ stm->work_queue = create_singlethread_workqueue("stmpe811");
+
+ if (!stm->work_queue) {
+ dev_err(&client->dev, "Failed to alloc workqueue\n");
+ ret = -ENOMEM;
+ goto err_free;
+ }
+
+ INIT_WORK(&stm->irq_work, stmpe811_irq_worker);
+
+ ret = stmpe811_block_read(stm, STMPE811_REG_CHIP_ID, 2, chip_id);
+ if ((ret < 0) || (((chip_id[0] << 8) | chip_id[1]) != 0x811)) {
+ dev_err(&client->dev, "could not verify stmpe811 chip id\n");
+ ret = -ENODEV;
+ goto err_destroy_workqueue;
+ }
+
+ stmpe811_reg_read(stm, STMPE811_REG_ID_VER, &chip_ver);
+ dev_info(&client->dev, "found stmpe811 chip id 0x%x version 0x%x\n",
+ (chip_id[0] << 8) | chip_id[1], chip_ver);
+
+ /* reset the device */
+ stmpe811_reg_write(stm, STMPE811_REG_SYS_CTRL1,
+ STMPE811_SYS_CTRL1_SOFT_RESET);
+
+ /* setup platform specific interrupt control flags and enable global
+ * interrupt */
+ stmpe811_reg_write(stm, STMPE811_REG_INT_CTRL,
+ STMPE811_INT_CTRL_GLOBAL_INT | pdata->int_conf);
+ ret =
+ request_irq(client->irq, stmpe811_irq, pdata->irq_flags, "stmpe811",
+ stm);
+ if (ret) {
+ dev_err(stm->dev, "Failed to request IRQ %d\n", ret);
+ goto err_destroy_workqueue;
+ }
+
+ if (pdata->flags & STMPE811_USE_TS)
+ ret =
+ mfd_add_devices(&client->dev, -1, &stmpe811_ts_dev, 1, NULL,
+ 0);
+ if (ret != 0)
+ goto err_release_irq;
+
+ if (pdata->flags & STMPE811_USE_GPIO)
+ ret =
+ mfd_add_devices(&client->dev, -1, &stmpe811_gpio_dev, 1,
+ NULL, 0);
+ if (ret != 0)
+ goto err_remove_mfd_devices;
+
+ return ret;
+
+err_remove_mfd_devices:
+ mfd_remove_devices(&client->dev);
+err_release_irq:
+ free_irq(client->irq, stm);
+err_destroy_workqueue:
+ destroy_workqueue(stm->work_queue);
+err_free:
+ mutex_destroy(&stm->io_lock);
+ i2c_set_clientdata(client, NULL);
+ kfree(stm);
+
+ return ret;
+}
+
+static int __devexit stmpe811_remove(struct i2c_client *client)
+{
+ struct stmpe811 *stm = i2c_get_clientdata(client);
+
+ stmpe811_reg_write(stm, STMPE811_REG_SYS_CTRL1,
+ STMPE811_SYS_CTRL1_HIBERNATE);
+
+ free_irq(stm->irq, stm);
+ destroy_workqueue(stm->work_queue);
+
+ mfd_remove_devices(&client->dev);
+
+ kfree(stm);
+
+ return 0;
+}
+
+static struct i2c_device_id stmpe811_id_table[] = {
+ {"stmpe811", 0x88},
+ { /* end of list */ }
+};
+
+static struct i2c_driver stmpe811_driver = {
+ .driver = {
+ .name = "stmpe811",
+ .owner = THIS_MODULE,
+ },
+ .probe = stmpe811_probe,
+ .remove = __devexit_p(stmpe811_remove),
+ .id_table = stmpe811_id_table,
+};
+
+static int __init stmpe811_init(void)
+{
+ return i2c_add_driver(&stmpe811_driver);
+}
+
+subsys_initcall(stmpe811_init);
+
+static void __exit stmpe811_exit(void)
+{
+ i2c_del_driver(&stmpe811_driver);
+}
+
+module_exit(stmpe811_exit);
+
+MODULE_DESCRIPTION
+ ("CORE Driver for STMPE811 Touch screen controller with GPIO expander");
+MODULE_AUTHOR("Luotao Fu <l.fu@xxxxxxxxxxxxxx>");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/stmpe811.h b/include/linux/mfd/stmpe811.h
new file mode 100644
index 0000000..ab2808a
--- /dev/null
+++ b/include/linux/mfd/stmpe811.h
@@ -0,0 +1,126 @@
+#ifndef __LINUX_MFD_STMPE811_H
+#define __LINUX_MFD_STMPE811_H
+
+#include <linux/i2c.h>
+#include <linux/workqueue.h>
+
+#define STMPE811_REG_CHIP_ID 0x00
+#define STMPE811_REG_ID_VER 0x02
+#define STMPE811_REG_SYS_CTRL1 0x03
+#define STMPE811_REG_SYS_CTRL2 0x04
+#define STMPE811_REG_SPI_CFG 0x08
+#define STMPE811_REG_INT_CTRL 0x09
+#define STMPE811_REG_INT_EN 0x0A
+#define STMPE811_REG_INT_STA 0x0B
+#define STMPE811_REG_GPIO_EN 0x0C
+#define STMPE811_REG_GPIO_INT_STA 0x0D
+#define STMPE811_REG_ADC_INT_EN 0x0E
+#define STMPE811_REG_ADC_INT_STA 0x0F
+#define STMPE811_REG_GPIO_SET_PIN 0x10
+#define STMPE811_REG_GPIO_CLR_PIN 0x11
+#define STMPE811_REG_GPIO_MP_STA 0x12
+#define STMPE811_REG_GPIO_DIR 0x13
+#define STMPE811_REG_GPIO_ED 0x14
+#define STMPE811_REG_GPIO_RE 0x15
+#define STMPE811_REG_GPIO_FE 0x16
+#define STMPE811_REG_GPIO_AF 0x17
+#define STMPE811_REG_ADC_CTRL1 0x20
+#define STMPE811_REG_ADC_CTRL2 0x21
+#define STMPE811_REG_ADC_CAPT 0x22
+#define STMPE811_REG_ADC_DATA_CH0 0x30
+#define STMPE811_REG_ADC_DATA_CH1 0x32
+#define STMPE811_REG_ADC_DATA_CH2 0x34
+#define STMPE811_REG_ADC_DATA_CH3 0x36
+#define STMPE811_REG_ADC_DATA_CH4 0x38
+#define STMPE811_REG_ADC_DATA_CH5 0x3A
+#define STMPE811_REG_ADC_DATA_CH6 0x3C
+#define STMPE811_REG_ADC_DATA_CH7 0x3E
+#define STMPE811_REG_TSC_CTRL 0x40
+#define STMPE811_REG_TSC_CFG 0x41
+#define STMPE811_REG_WDW_TR_X 0x42
+#define STMPE811_REG_WDW_TR_Y 0x44
+#define STMPE811_REG_WDW_BL_X 0x46
+#define STMPE811_REG_WDW_BL_Y 0x48
+#define STMPE811_REG_FIFO_TH 0x4A
+#define STMPE811_REG_FIFO_STA 0x4B
+#define STMPE811_REG_FIFO_SIZE 0x4C
+#define STMPE811_REG_TSC_DATA_X 0x4D
+#define STMPE811_REG_TSC_DATA_Y 0x4F
+#define STMPE811_REG_TSC_DATA_Z 0x51
+#define STMPE811_REG_TSC_DATA_XYZ 0x52
+#define STMPE811_REG_TSC_FRACTION_Z 0x56
+#define STMPE811_REG_TSC_DATA 0x57
+#define STMPE811_REG_TSC_DATA_SINGLE 0xD7
+#define STMPE811_REG_TSC_I_DRIVE 0x58
+#define STMPE811_REG_TSC_SHIELD 0x59
+#define STMPE811_REG_TEMP_CTRL 0x60
+
+#define STMPE811_IRQ_TOUCH_DET 0
+#define STMPE811_IRQ_FIFO_TH 1
+#define STMPE811_IRQ_FIFO_OFLOW 2
+#define STMPE811_IRQ_FIFO_FULL 3
+#define STMPE811_IRQ_FIFO_EMPTY 4
+#define STMPE811_IRQ_TEMP_SENS 5
+#define STMPE811_IRQ_ADC 6
+#define STMPE811_IRQ_GPIO 7
+#define STMPE811_NUM_IRQ 8
+
+#define STMPE811_SYS_CTRL1_HIBERNATE (1<<0)
+#define STMPE811_SYS_CTRL1_SOFT_RESET (1<<1)
+
+#define STMPE811_SYS_CTRL2_ADC_OFF (1<<0)
+#define STMPE811_SYS_CTRL2_TSC_OFF (1<<1)
+#define STMPE811_SYS_CTRL2_GPIO_OFF (1<<2)
+#define STMPE811_SYS_CTRL2_TS_OFF (1<<3)
+
+#define STMPE811_INT_CTRL_GLOBAL_INT (1<<0)
+#define STMPE811_INT_CTRL_INT_TYPE (1<<1)
+#define STMPE811_INT_CTRL_INT_POLARITY (1<<2)
+
+#define STMPE811_FIFO_STA_OFLOW (1<<7)
+#define STMPE811_FIFO_STA_FULL (1<<6)
+#define STMPE811_FIFO_STA_EMPTY (1<<5)
+#define STMPE811_FIFO_STA_TH_TRIG (1<<4)
+#define STMPE811_FIFO_STA_RESET (1<<0)
+
+#define STMPE811_USE_TS (1<<0)
+#define STMPE811_USE_GPIO (1<<1)
+
+struct stmpe811 {
+ struct device *dev;
+ struct i2c_client *i2c_client;
+
+ struct stmpe811_platform_data *pdata;
+ int irq;
+ irq_handler_t irqhandler[STMPE811_NUM_IRQ];
+ void *irqdata[STMPE811_NUM_IRQ];
+ struct work_struct irq_work;
+ struct workqueue_struct *work_queue;
+ struct mutex io_lock;
+ u8 active_flag;
+};
+
+struct stmpe811_gpio_platform_data {
+ unsigned int gpio_base;
+ int (*setup) (struct stmpe811 *stm);
+ void (*remove) (struct stmpe811 *stm);
+};
+
+struct stmpe811_platform_data {
+ unsigned int flags;
+ unsigned int irq_flags;
+ unsigned int int_conf;
+ struct stmpe811_gpio_platform_data *gpio_pdata;
+};
+
+int stmpe811_block_read(struct stmpe811 *stm, u8 reg, uint len, u8 *val);
+int stmpe811_reg_read(struct stmpe811 *pcf, u8 reg, u8 *val);
+int stmpe811_reg_write(struct stmpe811 *stm, u8 reg, u8 val);
+int stmpe811_reg_set_bits(struct stmpe811 *stm, u8 reg, u8 val);
+int stmpe811_reg_clear_bits(struct stmpe811 *stm, u8 reg, u8 val);
+
+int stmpe811_register_irq(struct stmpe811 *stm, int irq,
+ irq_handler_t handler, void *data);
+int stmpe811_free_irq(struct stmpe811 *stm, int irq);
+
+#endif
--
1.7.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/