Re: [PATCH v4 2/3] dt-bindings: remoteproc: qcom: Convert SC7280 MSS bindings to YAML

[Krzysztof Kozlowski]

On 20/05/2022 20:46, Sibi Sankar wrote:
>>> +  memory-region:
>>> +    maxItems: 2
>>> +    description: Phandle reference to the reserved-memory for the MBA region followed
>>> +                 by the modem region.
>>> +
>>> +  firmware-name:
>>> +    $ref: /schemas/types.yaml#/definitions/string-array
>>> +    maxItems: 2
>>
>> Instead of maxItems can this be
>>
>>         items:
>>           - description: Name of MBA firmware
>> 	 - description: Name of modem firmware
>>
>> so that we know the order? Same for 'memory-region' above.
> 
> ack
> 
>>
>>> +    description:
>>> +      The name of the MBA and modem firmware to be loaded for this remote processor.
>>> +
>>> +  qcom,halt-regs:
>>> +    $ref: /schemas/types.yaml#/definitions/phandle-array
>>
>> Should this have maxItems: 1? Or that's implicit from description?
> 
> It's implicit!

I am not aware of such implicit rule in schema. maxItems are always
required. If this is maxItems:1 it is not even an array.

> 
>>
>>> +    description:
>>> +      Phandle reference to a syscon representing TCSR followed by the
>>> +      four offsets within syscon for q6, modem, nc and vq6 halt registers.
>>> +
>>> +  qcom,ext-regs:
>>> +    $ref: /schemas/types.yaml#/definitions/phandle-array
>>
>> Should this have min/maxItems: 2?
> 
> ack

You should also define the items. This applies to all such fields. Check
the examples of syscon consumers.

> 
>>
>>> +    description:
>>> +      Two phandle references to syscons representing TCSR_REG and TCSR register
>>> +      space followed by the two offsets within the syscon to force_clk_en/rscc_disable
>>> +      and axim1_clk_off/crypto_clk_off registers respectively.
>>> +
>>> +  qcom,qaccept-regs:
>>> +    $ref: /schemas/types.yaml#/definitions/phandle-array
>>> +    description:
>>> +      Phandle reference to a syscon representing TCSR followed by the
>>> +      three offsets within syscon for mdm, cx and axi qaccept registers.
>>> +
>>> +  qcom,qmp:
>>> +    $ref: /schemas/types.yaml#/definitions/phandle
>>> +    description: Reference to the AOSS side-channel message RAM.
>>> +
>>> +  qcom,smem-states:
>>> +    $ref: /schemas/types.yaml#/definitions/phandle-array
>>> +    description: States used by the AP to signal the Hexagon core
>>> +    items:
>>> +      - description: Stop the modem
>>
>> This one did items for a phandle array so I think we should follow the
>> same above.
> 
> ack
> 
>>
>>> +
>>> +  qcom,smem-state-names:
>>> +    description: The names of the state bits used for SMP2P output
>>> +    const: stop
>>> +
>>> +  glink-edge:
>>> +    $ref: qcom,glink-edge.yaml#
>>> +    description:
>>> +      Qualcomm G-Link subnode which represents communication edge, channels
>>> +      and devices related to the DSP.
>> [..]
>>> +        power-domain-names = "cx", "mss";
>>> +
>>> +        memory-region = <&mba_mem>, <&mpss_mem>;
>>> +
>>> +        qcom,qmp = <&aoss_qmp>;
>>> +
>>> +        qcom,smem-states = <&modem_smp2p_out 0>;
>>> +        qcom,smem-state-names = "stop";
>>> +
>>> +        resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
>>> +                 <&pdc_reset PDC_MODEM_SYNC_RESET>;
>>> +        reset-names = "mss_restart", "pdc_reset";
>>> +
>>> +        qcom,halt-regs = <&tcsr_mutex 0x23000 0x25000 0x28000 0x33000>;
>>> +        qcom,ext-regs = <&tcsr 0x10000 0x10004 &tcsr_mutex 0x26004 0x26008>;
>>
>> Because it's two items I'd expect:
>> 	
>> 	<&tcsr 0x10000 0x10004>, <&tcsr_mutex 0x26004 0x26008>;
> 
> I guess both the ways work since the driver uses
> of_parse_phandle_with_fixed_args.

But only one is correct...


Best regards,
Krzysztof