Re: [PATCH v2 2/8] arm64: dts: qcom: pm8150: Add Base DTS file

[Niklas Cassel]

On Tue, Aug 20, 2019 at 12:12:10PM +0530, Vinod Koul wrote:
> Add base DTS file for pm8150 along with GPIOs, power-on, rtc and vadc
> nodes
> 
> Signed-off-by: Vinod Koul <vkoul@xxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/pm8150.dtsi | 95 ++++++++++++++++++++++++++++
>  1 file changed, 95 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/pm8150.dtsi
> 
> diff --git a/arch/arm64/boot/dts/qcom/pm8150.dtsi b/arch/arm64/boot/dts/qcom/pm8150.dtsi
> new file mode 100644
> index 000000000000..4a678be46d37
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pm8150.dtsi
> @@ -0,0 +1,95 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +// Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
> +// Copyright (c) 2019, Linaro Limited
> +
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +#include <dt-bindings/iio/qcom,spmi-vadc.h>
> +
> +&spmi_bus {
> +	pm8150_0: pmic@0 {
> +		compatible = "qcom,pm8150", "qcom,spmi-pmic";
> +		reg = <0x0 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pon: power-on@800 {
> +			compatible = "qcom,pm8916-pon";
> +			reg = <0x0800>;
> +			pwrkey {
> +				compatible = "qcom,pm8941-pwrkey";
> +				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;

Here you use 0 for 3rd cell

> +				debounce = <15625>;
> +				bias-pull-up;
> +				linux,code = <KEY_POWER>;
> +
> +				status = "disabled";
> +			};
> +		};
> +
> +		pm8150_adc: adc@3100 {
> +			compatible = "qcom,spmi-adc5";
> +			reg = <0x3100>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			#io-channel-cells = <1>;
> +			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;

Here you use 0x0 for 3rd cell, be consistent.

> +
> +			status = "disabled";
> +
> +			ref-gnd@0 {
> +				reg = <ADC5_REF_GND>;
> +				qcom,pre-scaling = <1 1>;
> +				label = "ref_gnd";
> +			};
> +
> +			vref-1p25@1 {
> +				reg = <ADC5_1P25VREF>;
> +				qcom,pre-scaling = <1 1>;
> +				label = "vref_1p25";
> +			};
> +
> +			die-temp@6 {
> +				reg = <ADC5_DIE_TEMP>;
> +				qcom,pre-scaling = <1 1>;
> +				label = "die_temp";
> +			};
> +		};
> +
> +		rtc@6000 {
> +			compatible = "qcom,pm8941-rtc";
> +			reg = <0x6000>;
> +			reg-names = "rtc", "alarm";
> +			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
> +
> +			status = "disabled";
> +		};
> +
> +		pm8150_gpios: gpio@c000 {
> +			compatible = "qcom,pm8150-gpio";
> +			reg = <0xc000>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
> +				     <0 0xc1 0 IRQ_TYPE_NONE>,
> +				     <0 0xc2 0 IRQ_TYPE_NONE>,
> +				     <0 0xc3 0 IRQ_TYPE_NONE>,
> +				     <0 0xc4 0 IRQ_TYPE_NONE>,
> +				     <0 0xc5 0 IRQ_TYPE_NONE>,
> +				     <0 0xc6 0 IRQ_TYPE_NONE>,
> +				     <0 0xc7 0 IRQ_TYPE_NONE>,
> +				     <0 0xc8 0 IRQ_TYPE_NONE>,
> +				     <0 0xc9 0 IRQ_TYPE_NONE>,
> +				     <0 0xca 0 IRQ_TYPE_NONE>,
> +				     <0 0xcb 0 IRQ_TYPE_NONE>;
> +		};
> +	};
> +
> +	pmic@1 {
> +		compatible = "qcom,pm8150", "qcom,spmi-pmic";
> +		reg = <0x1 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +	};
> +};
> -- 
> 2.20.1
>