Re: [PATCH 1/2] dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe Phy controller

From: Hanjie Lin
Date: Wed Aug 15 2018 - 23:01:22 EST




On 2018/8/15 6:50, Rob Herring wrote:
> On Tue, Aug 14, 2018 at 02:12:13AM -0400, Hanjie Lin wrote:
>> From: Yue Wang <yue.wang@xxxxxxxxxxx>
>
> Subject should be "dt-bindings: phy: ..."
>
>> The Meson-PCIE-PHY controller supports the 5-Gbps data rate
>> of the PCI Express Gen 2 specification and is backwardcompatible
>
> space

yes, I will fix
^
>
>> with the 2.5-Gbps Gen 1.1 specification with only
>> inferred idle detection supported on AMLOGIC SoCs.
>
> AMLOGIC or Amlogic?
>

yes, we will stick to 'Amlogic'

>>
>> Signed-off-by: Hanjie Lin <hanjie.lin@xxxxxxxxxxx>
>> Signed-off-by: Yue Wang <yue.wang@xxxxxxxxxxx>
>> ---
>> .../bindings/phy/amlogic,meson-pcie-phy.txt | 31 ++++++++++++++++++++++
>> 1 file changed, 31 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
>>
>> diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
>> new file mode 100644
>> index 0000000..db99085
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
>> @@ -0,0 +1,31 @@
>> +* Amlogic Meson AXG PCIE PHY binding
>> +
>> +Required properties:
>> +- compatible: Should be
>> + - "amlogic,axg-pcie-phy"
>> +- #phys-cells: must be 0 (see phy-bindings.txt in this directory)
>
> You don't need to distinguish port A and B?

No, we don't. Theoretically there is only one phy in the chip,
and we have distinguished ports by reset lines.

Thanks for all corrections and suggestions.

>
>> +- reg: The base address and length of the registers
>> +- resets: phandle to the reset lines
>> +- reset-names: must contain "phy" and "peripheral"
>> + - "port_a" Port A reset
>> + - "port_b" Port B reset
>> + - "phy" PHY reset
>> + - "apb" APB reset
>> +Optional properties:
>> +- phy-supply: see phy-bindings.txt in this directory
>> +
>> +Example:
>> + pcie_phy: pcie-phy@ff644000 {
>> + #phy-cells = <0>;
>> + compatible = "amlogic,axg-pcie-phy";
>> + reg = <0x0 0xff644000 0x0 0x2000>;
>> + resets = <&reset RESET_PCIE_A>,
>> + <&reset RESET_PCIE_B>,
>> + <&reset RESET_PCIE_PHY>,
>> + <&reset RESET_PCIE_APB>;
>> + reset-names =
>> + "port_a",
>> + "port_b",
>> + "phy",
>> + "apb";
>> + };
>> --
>> 2.7.4
>>
>
> .
>