Re: [PATCH v2] powerpc 8xx: Fixing issue with CONFIG_PIN_TLB

[Scott Wood]

On Fri, 2013-09-13 at 07:04 +0200, leroy christophe wrote:
> Le 12/09/2013 20:44, Scott Wood a Ãcrit :
> > On Thu, 2013-09-12 at 20:25 +0200, Christophe Leroy wrote:
> >> This is a reorganisation of the setup of the TLB at kernel startup, in order
> >> to handle the CONFIG_PIN_TLB case in accordance with chapter 8.10.3 of MPC866
> >> and MPC885 reference manuals.
> >>
> >> Signed-off-by: Christophe Leroy <christophe.leroy@xxxxxx>
> >>
> >> diff -ur linux-3.11.org/arch/powerpc/kernel/head_8xx.S linux-3.11/arch/powerpc/kernel/head_8xx.S
> >> --- linux-3.11.org/arch/powerpc/kernel/head_8xx.S	2013-09-02 22:46:10.000000000 +0200
> >> +++ linux-3.11/arch/powerpc/kernel/head_8xx.S	2013-09-09 11:28:54.000000000 +0200
> >> @@ -785,27 +785,24 @@
> >>    * these mappings is mapped by page tables.
> >>    */
> >>   initial_mmu:
> >> -	tlbia			/* Invalidate all TLB entries */
> >> -/* Always pin the first 8 MB ITLB to prevent ITLB
> >> -   misses while mucking around with SRR0/SRR1 in asm
> >> -*/
> >> -	lis	r8, MI_RSV4I@h
> >> -	ori	r8, r8, 0x1c00
> >> -
> >> +	lis	r8, MI_RESETVAL@h
> >>   	mtspr	SPRN_MI_CTR, r8	/* Set instruction MMU control */
> >>   
> >> -#ifdef CONFIG_PIN_TLB
> >> -	lis	r10, (MD_RSV4I | MD_RESETVAL)@h
> >> -	ori	r10, r10, 0x1c00
> >> -	mr	r8, r10
> >> -#else
> >>   	lis	r10, MD_RESETVAL@h
> >> -#endif
> >>   #ifndef CONFIG_8xx_COPYBACK
> >>   	oris	r10, r10, MD_WTDEF@h
> >>   #endif
> >>   	mtspr	SPRN_MD_CTR, r10	/* Set data TLB control */
> >>   
> >> +	tlbia			/* Invalidate all TLB entries */
> > Is this change to make sure we invalidate everything even if the
> > bootloader set RSV4I?
> Most probably. It is step 2 of the process defined in MPC866 and MPC885 
> Reference Manuals:
> 
> Â8.10.3 Loading Locked TLB Entries:
> The process of loading a single reserved entry in the TLB is as follows:

To minimize code churn we should just fix actual problems, rather than
shuffle things around to conform to a suggested sequence.  After all,
we're not just trying to load a single entry.

> >> +	ori	r8, r8, 0x1c00
> >> +	mtspr	SPRN_MI_CTR, r8	/* Set instruction MMU control */
> >> +#ifdef CONFIG_PIN_TLB
> >> +	ori	r10, r10, 0x1c00
> >> +	mtspr	SPRN_MD_CTR, r10	/* Set data TLB control */
> >> +#endif
> > Still 0x1c00?
> Yes, I kept the same entries in order to limit modifications:
> * 28 = First 8Mbytes page
> * 29 = IMMR
> * 30 = Second 8Mbytes page
> * 31 = Third 8Mbytes page

If you actually want to program them in increasing order then it looks
like you're still missing a write to CTR between the last two 8M entries
-- thus you'll overwrite the IMMR with the last 8M entry.  That was the
same problem that v1 fixed -- did that change get lost accidentally?

The hardware wants to decrement; why fight it?

> >>   	/* Now map the lower 8 Meg into the TLBs.  For this quick hack,
> >>   	 * we can load the instruction and data TLB registers with the
> >>   	 * same values.
> >> @@ -825,6 +822,12 @@
> >>   	mtspr	SPRN_MI_AP, r8
> >>   	mtspr	SPRN_MD_AP, r8
> >>   
> >> +	/* Always pin the first 8 MB ITLB to prevent ITLB
> >> +	 * misses while mucking around with SRR0/SRR1 in asm
> >> +	 */
> >> +	lis	r8, (MI_RSV4I | MI_RESETVAL)@h
> >> +	mtspr	SPRN_MI_CTR, r8	/* Set instruction MMU control */
> > Entry 0 is not pinnable.
> Here we are not trying to pin entry 0.

Sorry, misread the patch.

> We are at step 8, we are setting 
> MI_RSV4I. At the same time, we set MD_CTR to 0 which is off the pinned 
> range, to be sure that we won't overwrite one of the pinned entries.
>
> The main difference compared to the previous implementation is that 
> before, we were setting the RSV4I bit before loading the TLB entries. 
> Now, as defined in the Reference Manuals, we are doing it at the end.

Have you seen any evidence that it matters?

-Scott



--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/