Re: e1000e + suspend, 3.9-rc2

From: Jiri Slaby
Date: Wed Jun 12 2013 - 15:15:01 EST


On 04/15/2013 05:29 PM, Jiri Slaby wrote:
> On 03/29/2013 07:04 PM, Allan, Bruce W wrote:
>>> -----Original Message-----
>>> From: Jiri Slaby [mailto:jirislaby@xxxxxxxxx] On Behalf Of Jiri Slaby
>>> Sent: Tuesday, March 19, 2013 5:23 AM
>>> To: Konstantin Khlebnikov
>>> Cc: Borislav Petkov; Kirsher, Jeffrey T; Rafael J. Wysocki; Bjorn Helgaas;
>>> x86@xxxxxxxxxx; lkml; e1000-devel@xxxxxxxxxxxxxxxxxxxxx; Allan, Bruce W
>>> Subject: Re: e1000e + suspend, 3.9-rc2
>>>
>>>>>> Ok, I can still see the hardware error message when suspending:
>>>>>
>>>>> And with 3.8 plus these:
>>>>> PCI/PM: Clear state_saved during suspend
>>>>> e1000e: fix pci-device enable-counter balance
>>>>> e1000e: fix runtime power management transitions
>>>>> e1000e: fix accessing to suspended device
>>>>>
>>>>> I sometimes see this:
>>>>> pci_pm_suspend():e1000_suspend +0x0/0x10 [e1000e] returns -2
>>>>> dpm_run_callback(): pci_pm_suspend+0x0/0x140 returns -2
>>>>> PM: Device 0000:00:19.0 failed to suspend async: error -2
>>>>>
>>>>> Any ideas? Am I missing some patch still?
>>>>
>>>> Try this:
>>>> "PCI: Don't try to disable Bus Master on disconnected PCI devices"
>>>> https://patchwork.kernel.org/patch/2271641/
>>>>
>>>> But I'm not sure, probably it is unrelated because this code works only (?)
>>>> during shutdown/kexec sequences.
>>>
>>> I don't think it will help either. -2 here is -E1000_ERR_PHY from
>>> e1000e_write_phy_reg_mdic if I'm looking correctly. I.e. MDIC not ready
>>> or unlike MDIC_ERROR.
>>>
>>> I think this happened after I put the link down and tried to suspend.
>>>
>>> --
>>> js
>>> suse labs
>>
>> Sorry for not replying sooner, for some reason some of this thread was filtered
>> to my junk folder and I didnât see it until now.
>>
>> Jiri, can you provide the output of 'lspci -s 00:19.0 -n -vv' and confirm the scenario
>> in which the problem occurs? Is this easily reproduced?
>
> Sorry about the late reply, I totally forgot about this. lspci output is
> attached below. The scenario is not rigid as I'm not sure when exactly
> this happens. It looks like I have to use power saving on that device.
> And I don't need to use that device at all. Here is an excerpt from one
> kernel boot modulo e1000e where the error occurred.
>
> e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
> e1000e 0000:00:19.0: setting latency timer to 64
> e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic
> conservative mode
> e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
> e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 3c:97:0e:35:3d:dd
> e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
> e1000e 0000:00:19.0 eth0: MAC: 10, PHY: 11, PBA No: 1000FF-0FF
> e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
> e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
> e1000e 0000:00:19.0: setting latency timer to 64
> e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
> e1000e 0000:00:19.0: setting latency timer to 64
> e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
> e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
> e1000e 0000:00:19.0: irq 46 for MSI/MSI-X
> e1000e 0000:00:19.0: setting latency timer to 64
> e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
> e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
> e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
> e1000e 0000:00:19.0: setting latency timer to 64
> e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
> e1000e 0000:00:19.0: setting latency timer to 64
> e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
> e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
> e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
> e1000e 0000:00:19.0: setting latency timer to 64
> e1000e 0000:00:19.0: irq 45 for MSI/MSI-X
> pci_pm_suspend(): e1000_suspend+0x0/0x10 [e1000e] returns -2
> pci_pm_suspend(): e1000_suspend+0x0/0x10 [e1000e] returns -2
> pci_pm_suspend(): e1000_suspend+0x0/0x10 [e1000e] returns -2
> pci_pm_suspend(): e1000_suspend+0x0/0x10 [e1000e] returns -2
> pci_pm_suspend(): e1000_suspend+0x0/0x10 [e1000e] returns -2
> pci_pm_suspend(): e1000_suspend+0x0/0x10 [e1000e] returns -2

This still happens with 3.9.5 ...

I don't use wired net at all. This usually happens after I enable power
saving.

> 00:19.0 Ethernet controller [0200]: Intel Corporation 82579LM Gigabit
> Network Connection [8086:1502] (rev 04)
> Subsystem: Lenovo Device [17aa:21f3]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 46
> Region 0: Memory at f2500000 (32-bit, non-prefetchable) [size=128K]
> Region 1: Memory at f253b000 (32-bit, non-prefetchable) [size=4K]
> Region 2: I/O ports at 5080 [size=32]
> Capabilities: [c8] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000fee00398 Data: 0000
> Capabilities: [e0] PCI Advanced Features
> AFCap: TP+ FLR+
> AFCtrl: FLR-
> AFStatus: TP-
> Kernel driver in use: e1000e
>
>
> thanks,
>


--
js
suse labs
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/