[PATCH 21/35] mfd: ab8500-gpadc: Add support for the AB8540

From: Lee Jones
Date: Fri Feb 15 2013 - 08:01:59 EST

This patch enables the GPADC to work on AB8540 based platforms.

Signed-off-by: Lee Jones <lee.jones@xxxxxxxxxx>
---
drivers/mfd/ab8500-gpadc.c | 316 +++++++++++++++++++++++++++----
include/linux/mfd/abx500/ab8500-gpadc.h | 43 +++--
2 files changed, 305 insertions(+), 54 deletions(-)

diff --git a/drivers/mfd/ab8500-gpadc.c b/drivers/mfd/ab8500-gpadc.c
index 6b18975..f3712d8 100644
--- a/drivers/mfd/ab8500-gpadc.c
+++ b/drivers/mfd/ab8500-gpadc.c
@@ -37,6 +37,13 @@
#define AB8500_GPADC_AUTODATAL_REG 0x07
#define AB8500_GPADC_AUTODATAH_REG 0x08
#define AB8500_GPADC_MUX_CTRL_REG 0x09
+#define AB8540_GPADC_MANDATA2L_REG 0x09
+#define AB8540_GPADC_MANDATA2H_REG 0x0A
+#define AB8540_GPADC_APEAAX_REG 0x10
+#define AB8540_GPADC_APEAAT_REG 0x11
+#define AB8540_GPADC_APEAAM_REG 0x12
+#define AB8540_GPADC_APEAAH_REG 0x13
+#define AB8540_GPADC_APEAAL_REG 0x14

/*
* OTP register offsets
@@ -49,6 +56,10 @@
#define AB8500_GPADC_CAL_5 0x13
#define AB8500_GPADC_CAL_6 0x14
#define AB8500_GPADC_CAL_7 0x15
+/* New calibration for 8540 */
+#define AB8540_GPADC_OTP4_REG_7 0x38
+#define AB8540_GPADC_OTP4_REG_6 0x39
+#define AB8540_GPADC_OTP4_REG_5 0x3A

/* gpadc constants */
#define EN_VINTCORE12 0x04
@@ -67,6 +78,7 @@
#define GPADC_BUSY 0x01
#define EN_FALLING 0x10
#define EN_TRIG_EDGE 0x02
+#define EN_VBIAS_XTAL_TEMP 0x02

/* GPADC constants from AB8500 spec, UM0836 */
#define ADC_RESOLUTION 1024
@@ -85,8 +97,21 @@
#define ADC_CH_BKBAT_MIN 0
#define ADC_CH_BKBAT_MAX 3200

+/* GPADC constants from AB8540 spec */
+#define ADC_CH_IBAT_MIN (-6000) /* mA range measured by ADC for ibat*/
+#define ADC_CH_IBAT_MAX 6000
+#define ADC_CH_IBAT_MIN_V (-60) /* mV range measured by ADC for ibat*/
+#define ADC_CH_IBAT_MAX_V 60
+#define IBAT_VDROP_L (-56) /* mV */
+#define IBAT_VDROP_H 56
+
/* This is used to not lose precision when dividing to get gain and offset */
-#define CALIB_SCALE 1000
+#define CALIB_SCALE 1000
+/*
+ * Number of bits shift used to not lose precision
+ * when dividing to get ibat gain.
+ */
+#define CALIB_SHIFT_IBAT 20

/* Time in ms before disabling regulator */
#define GPADC_AUDOSUSPEND_DELAY 1
@@ -97,6 +122,7 @@ enum cal_channels {
ADC_INPUT_VMAIN = 0,
ADC_INPUT_BTEMP,
ADC_INPUT_VBAT,
+ ADC_INPUT_IBAT,
NBR_CAL_INPUTS,
};

@@ -107,8 +133,8 @@ enum cal_channels {
* @offset: Offset of the ADC channel
*/
struct adc_cal_data {
- u64 gain;
- u64 offset;
+ s64 gain;
+ s64 offset;
};

/**
@@ -183,6 +209,7 @@ int ab8500_gpadc_ad_to_voltage(struct ab8500_gpadc *gpadc, u8 channel,
gpadc->cal_data[ADC_INPUT_VMAIN].offset) / CALIB_SCALE;
break;

+ case XTAL_TEMP:
case BAT_CTRL:
case BTEMP_BALL:
case ACC_DETECT1:
@@ -201,6 +228,7 @@ int ab8500_gpadc_ad_to_voltage(struct ab8500_gpadc *gpadc, u8 channel,
break;

case MAIN_BAT_V:
+ case VBAT_TRUE_MEAS:
/* For some reason we don't have calibrated data */
if (!gpadc->cal_data[ADC_INPUT_VBAT].gain) {
res = ADC_CH_VBAT_MIN + (ADC_CH_VBAT_MAX -
@@ -244,6 +272,20 @@ int ab8500_gpadc_ad_to_voltage(struct ab8500_gpadc *gpadc, u8 channel,
ADC_RESOLUTION;
break;

+ case IBAT_VIRTUAL_CHANNEL:
+ /* For some reason we don't have calibrated data */
+ if (!gpadc->cal_data[ADC_INPUT_IBAT].gain) {
+ res = ADC_CH_IBAT_MIN + (ADC_CH_IBAT_MAX -
+ ADC_CH_IBAT_MIN) * ad_value /
+ ADC_RESOLUTION;
+ break;
+ }
+ /* Here we can use the calibrated data */
+ res = (int) (ad_value * gpadc->cal_data[ADC_INPUT_IBAT].gain +
+ gpadc->cal_data[ADC_INPUT_IBAT].offset)
+ >> CALIB_SHIFT_IBAT;
+ break;
+
default:
dev_err(gpadc->dev,
"unknown channel, not possible to convert\n");
@@ -307,9 +349,19 @@ EXPORT_SYMBOL(ab8500_gpadc_convert);
int ab8500_gpadc_read_raw(struct ab8500_gpadc *gpadc, u8 channel,
u8 avg_sample, u8 trig_edge, u8 trig_timer, u8 conv_type)
{
+ int raw_data;
+ raw_data = ab8500_gpadc_double_read_raw(gpadc, channel,
+ avg_sample, trig_edge, trig_timer, conv_type, NULL);
+ return raw_data;
+}
+
+int ab8500_gpadc_double_read_raw(struct ab8500_gpadc *gpadc, u8 channel,
+ u8 avg_sample, u8 trig_edge, u8 trig_timer, u8 conv_type,
+ int *ibat)
+{
int ret;
int looplimit = 0;
- u8 val, low_data, high_data;
+ u8 val, low_data, high_data, low_data2, high_data2;

if (!gpadc)
return -ENODEV;
@@ -362,7 +414,6 @@ int ab8500_gpadc_read_raw(struct ab8500_gpadc *gpadc, u8 channel,
default:
val = channel | AVG_16;
break;
-
}

if (conv_type == ADC_HW)
@@ -386,8 +437,8 @@ int ab8500_gpadc_read_raw(struct ab8500_gpadc *gpadc, u8 channel,
ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
AB8500_GPADC, AB8500_GPADC_CTRL1_REG,
EN_FALLING, EN_FALLING);
-
}
+
switch (channel) {
case MAIN_CHARGER_C:
case USB_CHARGER_C:
@@ -404,6 +455,55 @@ int ab8500_gpadc_read_raw(struct ab8500_gpadc *gpadc, u8 channel,
EN_BUF | EN_ICHAR,
EN_BUF | EN_ICHAR);
break;
+
+ case XTAL_TEMP:
+ if (conv_type == ADC_HW)
+ ret = abx500_mask_and_set_register_interruptible(
+ gpadc->dev,
+ AB8500_GPADC, AB8500_GPADC_CTRL1_REG,
+ EN_BUF | EN_TRIG_EDGE,
+ EN_BUF | EN_TRIG_EDGE);
+ else
+ ret = abx500_mask_and_set_register_interruptible(
+ gpadc->dev,
+ AB8500_GPADC, AB8500_GPADC_CTRL1_REG,
+ EN_BUF ,
+ EN_BUF);
+ break;
+
+ case VBAT_TRUE_MEAS:
+ if (conv_type == ADC_HW)
+ ret = abx500_mask_and_set_register_interruptible(
+ gpadc->dev,
+ AB8500_GPADC, AB8500_GPADC_CTRL1_REG,
+ EN_BUF | EN_TRIG_EDGE,
+ EN_BUF | EN_TRIG_EDGE);
+ else
+ ret = abx500_mask_and_set_register_interruptible(
+ gpadc->dev,
+ AB8500_GPADC, AB8500_GPADC_CTRL1_REG,
+ EN_BUF ,
+ EN_BUF);
+ break;
+
+ case BAT_CTRL_AND_IBAT:
+ case VBAT_MEAS_AND_IBAT:
+ case VBAT_TRUE_MEAS_AND_IBAT:
+ case BAT_TEMP_AND_IBAT:
+ if (conv_type == ADC_HW)
+ ret = abx500_mask_and_set_register_interruptible(
+ gpadc->dev,
+ AB8500_GPADC, AB8500_GPADC_CTRL1_REG,
+ EN_TRIG_EDGE,
+ EN_TRIG_EDGE);
+ else
+ ret = abx500_mask_and_set_register_interruptible(
+ gpadc->dev,
+ AB8500_GPADC, AB8500_GPADC_CTRL1_REG,
+ EN_BUF,
+ 0);
+ break;
+
case BTEMP_BALL:
if (!is_ab8500_2p0_or_earlier(gpadc->parent)) {
if (conv_type == ADC_HW)
@@ -474,21 +574,19 @@ int ab8500_gpadc_read_raw(struct ab8500_gpadc *gpadc, u8 channel,
/* wait for completion of conversion */
if (conv_type == ADC_HW) {
if (!wait_for_completion_timeout(&gpadc->ab8500_gpadc_complete,
- 2*HZ)) {
- dev_err(gpadc->dev,
- "timeout didn't receive"
- " hw GPADC conv interrupt\n");
- ret = -EINVAL;
- goto out;
+ 2 * HZ)) {
+ dev_err(gpadc->dev,
+ "timeout didn't receive hw GPADC conv interrupt\n");
+ ret = -EINVAL;
+ goto out;
}
} else {
if (!wait_for_completion_timeout(&gpadc->ab8500_gpadc_complete,
- msecs_to_jiffies(CONVERSION_TIME))) {
- dev_err(gpadc->dev,
- "timeout didn't receive"
- " sw GPADC conv interrupt\n");
- ret = -EINVAL;
- goto out;
+ msecs_to_jiffies(CONVERSION_TIME))) {
+ dev_err(gpadc->dev,
+ "timeout didn't receive sw GPADC conv interrupt\n");
+ ret = -EINVAL;
+ goto out;
}
}

@@ -526,6 +624,46 @@ int ab8500_gpadc_read_raw(struct ab8500_gpadc *gpadc, u8 channel,
goto out;
}
}
+ /* Check if double convertion is required */
+ if ((channel == BAT_CTRL_AND_IBAT) ||
+ (channel == VBAT_MEAS_AND_IBAT) ||
+ (channel == VBAT_TRUE_MEAS_AND_IBAT) ||
+ (channel == BAT_TEMP_AND_IBAT)) {
+
+ if (conv_type == ADC_HW) {
+ /* not supported */
+ ret = -ENOTSUPP;
+ dev_err(gpadc->dev,
+ "gpadc_conversion: only SW double conversion supported\n");
+ goto out;
+ } else {
+ /* Read the converted RAW data 2 */
+ ret = abx500_get_register_interruptible(gpadc->dev,
+ AB8500_GPADC, AB8540_GPADC_MANDATA2L_REG,
+ &low_data2);
+ if (ret < 0) {
+ dev_err(gpadc->dev,
+ "gpadc_conversion: read sw low data 2 failed\n");
+ goto out;
+ }
+
+ ret = abx500_get_register_interruptible(gpadc->dev,
+ AB8500_GPADC, AB8540_GPADC_MANDATA2H_REG,
+ &high_data2);
+ if (ret < 0) {
+ dev_err(gpadc->dev,
+ "gpadc_conversion: read sw high data 2 failed\n");
+ goto out;
+ }
+ if (ibat != NULL) {
+ *ibat = (high_data2 << 8) | low_data2;
+ } else {
+ dev_warn(gpadc->dev,
+ "gpadc_conversion: ibat not stored\n");
+ }
+
+ }
+ }

/* Disable GPADC */
ret = abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC,
@@ -589,15 +727,27 @@ static int otp_cal_regs[] = {
AB8500_GPADC_CAL_7,
};

+static int otp4_cal_regs[] = {
+ AB8540_GPADC_OTP4_REG_7,
+ AB8540_GPADC_OTP4_REG_6,
+ AB8540_GPADC_OTP4_REG_5,
+};
+
static void ab8500_gpadc_read_calibration_data(struct ab8500_gpadc *gpadc)
{
int i;
int ret[ARRAY_SIZE(otp_cal_regs)];
u8 gpadc_cal[ARRAY_SIZE(otp_cal_regs)];
-
+ int ret_otp4[ARRAY_SIZE(otp4_cal_regs)];
+ u8 gpadc_otp4[ARRAY_SIZE(otp4_cal_regs)];
int vmain_high, vmain_low;
int btemp_high, btemp_low;
int vbat_high, vbat_low;
+ int ibat_high, ibat_low;
+ s64 V_gain, V_offset, V2A_gain, V2A_offset;
+ struct ab8500 *ab8500;
+
+ ab8500 = gpadc->parent;

/* First we read all OTP registers and store the error code */
for (i = 0; i < ARRAY_SIZE(otp_cal_regs); i++) {
@@ -617,7 +767,7 @@ static void ab8500_gpadc_read_calibration_data(struct ab8500_gpadc *gpadc)
* bt_h/l = btemp_high/low
* vb_h/l = vbat_high/low
*
- * Data bits:
+ * Data bits 8500/9540:
* | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
* |.......|.......|.......|.......|.......|.......|.......|.......
* | | vm_h9 | vm_h8
@@ -635,6 +785,35 @@ static void ab8500_gpadc_read_calibration_data(struct ab8500_gpadc *gpadc)
* | vb_l5 | vb_l4 | vb_l3 | vb_l2 | vb_l1 | vb_l0 |
* |.......|.......|.......|.......|.......|.......|.......|.......
*
+ * Data bits 8540:
+ * OTP2
+ * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * |
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | vm_h9 | vm_h8 | vm_h7 | vm_h6 | vm_h5 | vm_h4 | vm_h3 | vm_h2
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | vm_h1 | vm_h0 | vm_l4 | vm_l3 | vm_l2 | vm_l1 | vm_l0 | bt_h9
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | bt_h8 | bt_h7 | bt_h6 | bt_h5 | bt_h4 | bt_h3 | bt_h2 | bt_h1
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | bt_h0 | bt_l4 | bt_l3 | bt_l2 | bt_l1 | bt_l0 | vb_h9 | vb_h8
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | vb_h7 | vb_h6 | vb_h5 | vb_h4 | vb_h3 | vb_h2 | vb_h1 | vb_h0
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | vb_l5 | vb_l4 | vb_l3 | vb_l2 | vb_l1 | vb_l0 |
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ *
+ * Data bits 8540:
+ * OTP4
+ * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | | ib_h9 | ib_h8 | ib_h7
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | ib_h6 | ib_h5 | ib_h4 | ib_h3 | ib_h2 | ib_h1 | ib_h0 | ib_l5
+ * |.......|.......|.......|.......|.......|.......|.......|.......
+ * | ib_l4 | ib_l3 | ib_l2 | ib_l1 | ib_l0 |
+ *
*
* Ideal output ADC codes corresponding to injected input voltages
* during manufacturing is:
@@ -647,38 +826,96 @@ static void ab8500_gpadc_read_calibration_data(struct ab8500_gpadc *gpadc)
* vbat_low: Vin = 2380mV / ADC ideal code = 33
*/

- /* Calculate gain and offset for VMAIN if all reads succeeded */
- if (!(ret[0] < 0 || ret[1] < 0 || ret[2] < 0)) {
- vmain_high = (((gpadc_cal[0] & 0x03) << 8) |
- ((gpadc_cal[1] & 0x3F) << 2) |
- ((gpadc_cal[2] & 0xC0) >> 6));
+ if (is_ab8540(ab8500)) {
+ /* Calculate gain and offset for VMAIN if all reads succeeded*/
+ if (!(ret[1] < 0 || ret[2] < 0)) {
+ vmain_high = (((gpadc_cal[1] & 0xFF) << 2) |
+ ((gpadc_cal[2] & 0xC0) >> 6));
+ vmain_low = ((gpadc_cal[2] & 0x3E) >> 1);
+ gpadc->cal_data[ADC_INPUT_VMAIN].gain = CALIB_SCALE *
+ (19500 - 315) / (vmain_high - vmain_low);
+ gpadc->cal_data[ADC_INPUT_VMAIN].offset = CALIB_SCALE *
+ 19500 - (CALIB_SCALE * (19500 - 315) /
+ (vmain_high - vmain_low)) * vmain_high;
+ } else {
+ gpadc->cal_data[ADC_INPUT_VMAIN].gain = 0;
+ }

- vmain_low = ((gpadc_cal[2] & 0x3E) >> 1);
+ /* Read IBAT calibration Data */
+ for (i = 0; i < ARRAY_SIZE(otp4_cal_regs); i++) {
+ ret_otp4[i] = abx500_get_register_interruptible(
+ gpadc->dev, AB8500_OTP_EMUL,
+ otp4_cal_regs[i], &gpadc_otp4[i]);
+ if (ret_otp4[i] < 0)
+ dev_err(gpadc->dev,
+ "%s: read otp4 reg 0x%02x failed\n",
+ __func__, otp4_cal_regs[i]);
+ }

- gpadc->cal_data[ADC_INPUT_VMAIN].gain = CALIB_SCALE *
- (19500 - 315) / (vmain_high - vmain_low);
+ /* Calculate gain and offset for IBAT if all reads succeeded */
+ if (!(ret_otp4[0] < 0 || ret_otp4[1] < 0 || ret_otp4[2] < 0)) {
+ ibat_high = (((gpadc_otp4[0] & 0x07) << 7) |
+ ((gpadc_otp4[1] & 0xFE) >> 1));
+ ibat_low = (((gpadc_otp4[1] & 0x01) << 5) |
+ ((gpadc_otp4[2] & 0xF8) >> 3));
+
+ V_gain = ((IBAT_VDROP_H - IBAT_VDROP_L)
+ << CALIB_SHIFT_IBAT) / (ibat_high - ibat_low);
+
+ V_offset = (IBAT_VDROP_H << CALIB_SHIFT_IBAT) -
+ (((IBAT_VDROP_H - IBAT_VDROP_L) <<
+ CALIB_SHIFT_IBAT) / (ibat_high - ibat_low))
+ * ibat_high;
+ /*
+ * Result obtained is in mV (at a scale factor),
+ * we need to calculate gain and offset to get mA
+ */
+ V2A_gain = (ADC_CH_IBAT_MAX - ADC_CH_IBAT_MIN)/
+ (ADC_CH_IBAT_MAX_V - ADC_CH_IBAT_MIN_V);
+ V2A_offset = ((ADC_CH_IBAT_MAX_V * ADC_CH_IBAT_MIN -
+ ADC_CH_IBAT_MAX * ADC_CH_IBAT_MIN_V)
+ << CALIB_SHIFT_IBAT)
+ / (ADC_CH_IBAT_MAX_V - ADC_CH_IBAT_MIN_V);
+
+ gpadc->cal_data[ADC_INPUT_IBAT].gain = V_gain * V2A_gain;
+ gpadc->cal_data[ADC_INPUT_IBAT].offset = V_offset *
+ V2A_gain + V2A_offset;
+ } else {
+ gpadc->cal_data[ADC_INPUT_IBAT].gain = 0;
+ }

- gpadc->cal_data[ADC_INPUT_VMAIN].offset = CALIB_SCALE * 19500 -
- (CALIB_SCALE * (19500 - 315) /
- (vmain_high - vmain_low)) * vmain_high;
+ dev_dbg(gpadc->dev, "IBAT gain %llu offset %llu\n",
+ gpadc->cal_data[ADC_INPUT_IBAT].gain,
+ gpadc->cal_data[ADC_INPUT_IBAT].offset);
} else {
- gpadc->cal_data[ADC_INPUT_VMAIN].gain = 0;
+ /* Calculate gain and offset for VMAIN if all reads succeeded */
+ if (!(ret[0] < 0 || ret[1] < 0 || ret[2] < 0)) {
+ vmain_high = (((gpadc_cal[0] & 0x03) << 8) |
+ ((gpadc_cal[1] & 0x3F) << 2) |
+ ((gpadc_cal[2] & 0xC0) >> 6));
+ vmain_low = ((gpadc_cal[2] & 0x3E) >> 1);
+
+ gpadc->cal_data[ADC_INPUT_VMAIN].gain = CALIB_SCALE *
+ (19500 - 315) / (vmain_high - vmain_low);
+
+ gpadc->cal_data[ADC_INPUT_VMAIN].offset = CALIB_SCALE *
+ 19500 - (CALIB_SCALE * (19500 - 315) /
+ (vmain_high - vmain_low)) * vmain_high;
+ } else {
+ gpadc->cal_data[ADC_INPUT_VMAIN].gain = 0;
+ }
}
-
/* Calculate gain and offset for BTEMP if all reads succeeded */
if (!(ret[2] < 0 || ret[3] < 0 || ret[4] < 0)) {
btemp_high = (((gpadc_cal[2] & 0x01) << 9) |
- (gpadc_cal[3] << 1) |
- ((gpadc_cal[4] & 0x80) >> 7));
-
+ (gpadc_cal[3] << 1) | ((gpadc_cal[4] & 0x80) >> 7));
btemp_low = ((gpadc_cal[4] & 0x7C) >> 2);

gpadc->cal_data[ADC_INPUT_BTEMP].gain =
CALIB_SCALE * (1300 - 21) / (btemp_high - btemp_low);
-
gpadc->cal_data[ADC_INPUT_BTEMP].offset = CALIB_SCALE * 1300 -
- (CALIB_SCALE * (1300 - 21) /
- (btemp_high - btemp_low)) * btemp_high;
+ (CALIB_SCALE * (1300 - 21) / (btemp_high - btemp_low))
+ * btemp_high;
} else {
gpadc->cal_data[ADC_INPUT_BTEMP].gain = 0;
}
@@ -690,7 +927,6 @@ static void ab8500_gpadc_read_calibration_data(struct ab8500_gpadc *gpadc)

gpadc->cal_data[ADC_INPUT_VBAT].gain = CALIB_SCALE *
(4700 - 2380) / (vbat_high - vbat_low);
-
gpadc->cal_data[ADC_INPUT_VBAT].offset = CALIB_SCALE * 4700 -
(CALIB_SCALE * (4700 - 2380) /
(vbat_high - vbat_low)) * vbat_high;
diff --git a/include/linux/mfd/abx500/ab8500-gpadc.h b/include/linux/mfd/abx500/ab8500-gpadc.h
index 7694e7a..4131437 100644
--- a/include/linux/mfd/abx500/ab8500-gpadc.h
+++ b/include/linux/mfd/abx500/ab8500-gpadc.h
@@ -12,19 +12,32 @@

/* GPADC source: From datasheet(ADCSwSel[4:0] in GPADCCtrl2
* and ADCHwSel[4:0] in GPADCCtrl3 ) */
-#define BAT_CTRL 0x01
-#define BTEMP_BALL 0x02
-#define MAIN_CHARGER_V 0x03
-#define ACC_DETECT1 0x04
-#define ACC_DETECT2 0x05
-#define ADC_AUX1 0x06
-#define ADC_AUX2 0x07
-#define MAIN_BAT_V 0x08
-#define VBUS_V 0x09
-#define MAIN_CHARGER_C 0x0A
-#define USB_CHARGER_C 0x0B
-#define BK_BAT_V 0x0C
-#define DIE_TEMP 0x0D
+#define BAT_CTRL 0x01
+#define BTEMP_BALL 0x02
+#define MAIN_CHARGER_V 0x03
+#define ACC_DETECT1 0x04
+#define ACC_DETECT2 0x05
+#define ADC_AUX1 0x06
+#define ADC_AUX2 0x07
+#define MAIN_BAT_V 0x08
+#define VBUS_V 0x09
+#define MAIN_CHARGER_C 0x0A
+#define USB_CHARGER_C 0x0B
+#define BK_BAT_V 0x0C
+#define DIE_TEMP 0x0D
+#define USB_ID 0x0E
+#define XTAL_TEMP 0x12
+#define VBAT_TRUE_MEAS 0x13
+#define BAT_CTRL_AND_IBAT 0x1C
+#define VBAT_MEAS_AND_IBAT 0x1D
+#define VBAT_TRUE_MEAS_AND_IBAT 0x1E
+#define BAT_TEMP_AND_IBAT 0x1F
+
+/* Virtual channel used only for ibat convertion to ampere
+ * Battery current conversion (ibat) cannot be requested as a single conversion
+ * but it is always in combination with other input requests
+ */
+#define IBAT_VIRTUAL_CHANNEL 0xFF

#define SAMPLE_1 1
#define SAMPLE_4 4
@@ -37,7 +50,6 @@
#define ADC_SW 0
#define ADC_HW 1

-
struct ab8500_gpadc;

struct ab8500_gpadc *ab8500_gpadc_get(char *name);
@@ -51,6 +63,9 @@ static inline int ab8500_gpadc_convert(struct ab8500_gpadc *gpadc, u8 channel)

int ab8500_gpadc_read_raw(struct ab8500_gpadc *gpadc, u8 channel,
u8 avg_sample, u8 trig_edge, u8 trig_timer, u8 conv_type);
+int ab8500_gpadc_double_read_raw(struct ab8500_gpadc *gpadc, u8 channel,
+ u8 avg_sample, u8 trig_edge, u8 trig_timer, u8 conv_type,
+ int *ibat);
int ab8500_gpadc_ad_to_voltage(struct ab8500_gpadc *gpadc,
u8 channel, int ad_value);

--
1.7.10.4

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/