Re: [PATCH 3/5] arm: dts: omap4-panda: Add I2c pinctrl data

[Jon Hunter]

On 02/13/2013 03:28 AM, Sourav Poddar wrote:
> Booting 3.8-rc6 on omap4 panda results in the following error
> 
> [    0.444427] omap_i2c 48070000.i2c: did not get pins for i2c error: -19
> [    0.445770] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz
> [    0.473937] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
> [    0.474670] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz
> [    0.474822] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
> [    0.476379] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz
> [    0.477294] omap_i2c 48350000.i2c: did not get pins for i2c error: -19
> [    0.477996] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz
> [    0.483398] Switching to clocksource 32k_counter
> 
> This happens because omap4 panda dts file is not adapted to use i2c through
> pinctrl framework. Populating i2c pinctrl data to get rid of the error.

What about the panda-es and panda-a4?

> Tested on omap4460 panda with 3.8-rc6 kernel.
> 
> Signed-off-by: Sourav Poddar <sourav.poddar@xxxxxx>
> Reported-by: Luciano Coelho <coelho@xxxxxx>
> ---
>  arch/arm/boot/dts/omap4-panda.dts |   40 +++++++++++++++++++++++++++++++++++++
>  1 files changed, 40 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts
> index 4122efe..f951e6b 100644
> --- a/arch/arm/boot/dts/omap4-panda.dts
> +++ b/arch/arm/boot/dts/omap4-panda.dts
> @@ -110,9 +110,40 @@
>  			0x58 0x10b	/* hdmi_hpd.gpio_63 INPUT PULLDOWN | MODE3 */
>  		>;
>  	};
> +
> +	i2c1_pins: pinmux_i2c1_pins {
> +		pinctrl-single,pins = <
> +			0xe2 0x118        /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */
> +			0xe4 0x118        /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */
> +		>;
> +	};
> +
> +	i2c2_pins: pinmux_i2c2_pins {
> +		pinctrl-single,pins = <
> +			0xe6 0x118        /* i2c2_scl PULLUP | INPUTENABLE | MODE0 */
> +			0xe8 0x118        /* i2c2_sda PULLUP | INPUTENABLE | MODE0 */
> +		>;
> +	};
> +
> +	i2c3_pins: pinmux_i2c3_pins {
> +		pinctrl-single,pins = <
> +			0xea 0x118        /* i2c3_scl PULLUP | INPUTENABLE | MODE0 */
> +			0xec 0x118     /* i2c3_sda PULLUP | INPUTENABLE | MODE0 */
> +		>;
> +	};
> +
> +	i2c4_pins: pinmux_i2c4_pins {
> +		pinctrl-single,pins = <
> +			0xee 0x118        /* i2c4_scl PULLUP | INPUTENABLE | MODE0 */
> +			0xf0 0x118     /* i2c4_sda PULLUP | INPUTENABLE | MODE0 */
> +		>;
> +	};
>  };

A quick look at the data manual shows that omap4430 and omap4460 has the
same pin mux options for i2c. Furthermore, the data manual shows only
one mux option for i2c1-4. Therefore, should these mux options be placed
in omap4.dtsi? Boards not using specific i2c controllers can disabled
them in there board dts file (same way we do for mmc).

Cheers
Jon
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/