Re: [PATCH 2.6.38-rc7]TAOS 258x: Device Driver

From: Jonathan Cameron
Date: Wed Mar 09 2011 - 14:13:34 EST


On 03/09/11 01:32, Jon Brenner wrote:
> From: J. August Brenner <jbrenner@xxxxxxxxxxx>
>
> This driver supports the TAOS tsl258x family of ALS sensors.
> This driver provides ALS data (lux), and device configuration via
> isysfs/iio.
> More significantly, this driver provides the capability to be fed 'glass
> coefficients' to accommodate varying system designs (bezels, faceplates,
> etc.).
>
Jon,

Please cc all the relevant subsystem lists...(done)

Sorry to say I'm pretty militant about attribute names.
My job is to ensure we end up with a generalizable set,
consistent across lots of different sensor types. That
consistency does restrict what is acceptable a lot more
than would be true if we were only interested in light
sensors. That's not say I'm not happy to have futher
discussions on these points.

Otherwise, getting there. Various comments inline.

> Signed-off-by: Jon August Brenner <jbrenner@xxxxxxxxxxx>
>
> ---
>
>>From 5b8364f9828dbad5fbfff96385e3fc2a6a6d56ed Mon Sep 17 00:00:00 2001
> From: Jon Brenner <jbrenner@xxxxxxxxxxx>
> Date: Tue, 8 Mar 2011 18:37:13 -0600
> Subject: [PATCH] TAOS driver for the tsl258x family of devices.
This should be in the patch body. Guessing output of git format-patch?
It's for use with git send-email and forms the email header.

> ---
> Makefile | 2 +-
> .../staging/iio/Documentation/sysfs-bus-iio-light | 63 ++
> drivers/staging/iio/light/Kconfig | 7 +
> drivers/staging/iio/light/Makefile | 1 +
> drivers/staging/iio/light/tsl258x.c | 1010 ++++++++++++++++++++
> 5 files changed, 1082 insertions(+), 1 deletions(-)
>
> diff --git a/Makefile b/Makefile
> index 26d7d82..2f7d922 100644
> --- a/Makefile
> +++ b/Makefile
This shouldn't be in a driver patch.
> @@ -1,7 +1,7 @@
> VERSION = 2
> PATCHLEVEL = 6
> SUBLEVEL = 38
> -EXTRAVERSION = -rc6
> +EXTRAVERSION = -rc7
> NAME = Flesh-Eating Bats with Fangs
>
> # *DOCUMENTATION*
> diff --git a/drivers/staging/iio/Documentation/sysfs-bus-iio-light b/drivers/staging/iio/Documentation/sysfs-bus-iio-light
> index 5d84856..5affc2a 100644
> --- a/drivers/staging/iio/Documentation/sysfs-bus-iio-light
> +++ b/drivers/staging/iio/Documentation/sysfs-bus-iio-light
> @@ -62,3 +62,66 @@ Description:
> sensing mode. This value should be the output from a reading
> and if expressed in SI units, should include _input. If this
> value is not in SI units, then it should include _raw.
> +
> +What: /sys/bus/iio/devices/device[n]/device_state
> +KernelVersion: 2.6.37
> +Contact: linux-iio@xxxxxxxxxxxxxxx
> +Description:
> + This property gets/sets the TAOS tsl258x power state.
This certainly looks more general than that. It's not light sensor specific
so should be in sysfs-bus-iio rather than the light related doc. Having said
that it's also a rather non specific description / name.

I've been generally pushing against having this sort of power control as
an explicit attribute in the iio abi simply because the right way to handle
this is probably runtime power management. We did let a few drivers do
this early on simply because they predated runtime PM. That framework has
the advantage that it also allows for the bus to be turned off if no
devices on it need to be talked to. It may be time to reopen the previous
discussion of how to allow userspace to explicitly say it doesn't care
if a device is powered up...

> +
> +What: /sys/bus/iio/devices/device[n]/als_gain
> +KernelVersion: 2.6.37
> +Contact: linux-iio@xxxxxxxxxxxxxxx
> +Description:
> + This property gets/sets the TAOS tsl258x analog gain settings
> + of the device.
Again, please get the mention of particular part out of the description.
Although it isn't explicitly specified (yet) for light sensors, we do have
an equivalent (I think) of this assuming it is a linear relationship?
(google found me a datasheet so at least superficially I think it is).
That attribute is illuminance_calibscale (calib bit means it is applied
on device or in driver rather than telling userspace what needs to be
applied by it). (yikes, just noticed that this is wrong in tsl2563 where
we have calibgain due to some inconsistency on my part a while back).

Also avoid 'magic' numbers as seen here. There are a finite range of
possible values, so have an extra attributes - here illuminance_calibscale_available
which is read only and gives the string "1 8 16 111" and make illuminance_calibscale
return -EINVAL if the value written is not one of these. sysfs_streq is really
handy for this sort of matching.

> +
> +What: /sys/bus/iio/devices/device[n]/als_time
> +KernelVersion: 2.6.37
> +Contact: linux-iio@xxxxxxxxxxxxxxx
> +Description:
> + This property gets/sets the TAOS tsl258x ADC channel integration
> + time in 2.7ms increments.
Again, this is more general than just working for the tsl258x driver. That 2.7ms
isn't though. Please make this a value in millisecs (fixed point) then deal
with conversion to this base in the driver. On this one, it is closely related
to the 'period' attributes that exist for various events. Perhaps illuminance_period
is a more consistent name?
> +
> +What: /sys/bus/iio/devices/device[n]/als_trim
> +KernelVersion: 2.6.37
> +Contact: linux-iio@xxxxxxxxxxxxxxx
> +Description:
> + This property gets/sets the TAOS tsl258x ADC active gain scale.
This one needs more detail before I can comment. I can't figure out what it
actually is!
> +
> +What: /sys/bus/iio/devices/device[n]/als_target
> +KernelVersion: 2.6.37
> +Contact: linux-iio@xxxxxxxxxxxxxxx
> +Description:
> + This property gets/sets the TAOS tsl258x ADC last known external
> + lux measurement used in calibration.
als_target -> illuminance0_target
lux -> illuminance.
What units?
Sounds more general than the tsl258x to me so perhaps say that chip is an example
of its use?
> +
> +What: /sys/bus/iio/devices/device[n]/lux
> +KernelVersion: 2.6.37
> +Contact: linux-iio@xxxxxxxxxxxxxxx
> +Description:
> + This property gets the TAOS tsl258x calculated lux value.
Sorry, lux is a unit. Attributes are named after what is being measured. Hence
illuminance. Might seem reasonable to use the unit, but then what would we
do for acceleration (m/s^2)? I guess we can reopen this debate again if you are
really attached to lux... Also needs to be illuminance0_input. The input specifices
that it is in the base unit (lux) rather than raw. We stick to this form
to maintain compatiblity with hwmon which has been around a lot longer than us!
> +
> +What: /sys/bus/iio/devices/device[n]/lux_table
> +KernelVersion: 2.6.37
> +Contact: linux-iio@xxxxxxxxxxxxxxx
> +Description:
> + This property gets/sets the TAOS tsl258x lux table of coefficients
> + that are used to calculate lux.
> +
> +What: /sys/bus/iio/devices/device[n]/reg_offset
> +KernelVersion: 2.6.37
> +Contact: linux-iio@xxxxxxxxxxxxxxx
> +Description:
> + This property gets/sets an index the TAOS tsl258x internel register
> + for r/w of selected register.
Sorry, not letting direct register write attributes in. What do you need these
for? Can it really not be replaced by more informative attributes?
> +
> +What: /sys/bus/iio/devices/device[n]/reg_offset
> +KernelVersion: 2.6.37
> +Contact: linux-iio@xxxxxxxxxxxxxxx
> +Description:
> + This property gets/sets an TAOS tsl258x internel register value
> + indexed by reg_offset.
> +
Extra empty lines. Please remove. Also please run checkpatch over this patch. I think
there are some extra tabs on these lines that won't have gotten through that.
> +
> +
> \ No newline at end of file
> diff --git a/drivers/staging/iio/light/Kconfig b/drivers/staging/iio/light/Kconfig
> index 36d8bbe..ae499b8 100644
> --- a/drivers/staging/iio/light/Kconfig
> +++ b/drivers/staging/iio/light/Kconfig
> @@ -13,6 +13,13 @@ config SENSORS_TSL2563
> This driver can also be built as a module. If so, the module
> will be called tsl2563.
>
> +config TAOS_258x
> + tristate "TAOS TSL258x device driver"
> + default m
> + help
> + Provides support for the TAOS tsl258x family of devices.
> + Access ALS data/control via sysfs/iio.
Please list devices. People tend to grep the tree for the part number of the
device that they actually have hence it is useful to have them all explicitly
listed here. In combination with the id table listing them all this also tends
to tell people if the developer thinks it will work with the part they have.
> +
> config SENSORS_ISL29018
> tristate "ISL 29018 light and proximity sensor"
> depends on I2C
> diff --git a/drivers/staging/iio/light/Makefile b/drivers/staging/iio/light/Makefile
> index 9142c0e..4395db8 100644
> --- a/drivers/staging/iio/light/Makefile
> +++ b/drivers/staging/iio/light/Makefile
> @@ -3,4 +3,5 @@
> #
>
> obj-$(CONFIG_SENSORS_TSL2563) += tsl2563.o
> +obj-$(CONFIG_TAOS_258x) += tsl258x.o
> obj-$(CONFIG_SENSORS_ISL29018) += isl29018.o
> diff --git a/drivers/staging/iio/light/tsl258x.c b/drivers/staging/iio/light/tsl258x.c
> new file mode 100644
> index 0000000..225d85b
> --- /dev/null
> +++ b/drivers/staging/iio/light/tsl258x.c
> @@ -0,0 +1,1010 @@
> +/*
> + * Device driver for monitoring ambient light intensity (lux)
> + * within the TAOS tsl258x family of devices
> + *
> + * Copyright (c) 2011, TAOS Corporation.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
> + * more details.
> + *
> + * You should have received a copy of the GNU General Public License along
> + * with this program; if not, write to the Free Software Foundation, Inc.,
> + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/i2c.h>
> +#include <linux/errno.h>
> +#include <linux/delay.h>
> +#include <linux/string.h>
> +#include <linux/mutex.h>
> +#include "../iio.h"
> +
> +#define DEVICE_ID "tsl258x"
> +
> +#define MAX_DEVICE_REGS 32
> +
I'm guessing this is an internal part name? If possible please replace
with the numbers people will see on datasheets.
> +/* Triton register offsets */
> +#define TAOS_REG_MAX 8
> +
> +/* Device Registers and Masks */
> +#define TSL258X_CNTRL 0x00
This needs a a comment. Why two regs with the same address?
> +#define TSL258X_STATUS 0x00
> +#define TSL258X_ALS_TIME 0X01
> +#define TSL258X_INTERRUPT 0x02
> +#define TSL258X_GAIN 0x07
> +#define TSL258X_REVID 0x11
> +#define TSL258X_CHIPID 0x12

Cryptic name and never used. Please remove.
> +#define TSL258X_SMB_4 0x13
> +#define TSL258X_ALS_CHAN0LO 0x14
> +#define TSL258X_ALS_CHAN0HI 0x15
> +#define TSL258X_ALS_CHAN1LO 0x16
> +#define TSL258X_ALS_CHAN1HI 0x17
> +#define TSL258X_TMR_LO 0x18
> +#define TSL258X_TMR_HI 0x19
> +
> +/* Skate cmd reg masks */
> +#define TSL258X_CMD_REG 0x80
> +#define TSL258X_CMD_BYTE_RW 0x00

This name confuses me. Looks like it sets word protocol so why the block bit?
Also not used so could just get rid of it.
> +#define TSL258X_CMD_WORD_BLK_RW 0x20
> +#define TSL258X_CMD_SPL_FN 0x60

Nitpick. Later reference to INT have an _ after them. Perhaps add one for consistency?
> +#define TSL258X_CMD_ALS_INTCLR 0X01
> +
Err. Skate?
> +/* Skate cntrl reg masks */
Not used and rather pointless. Default would be to assume writing 0
cleared a register? (or does this mean something else?)
> +#define TSL258X_CNTL_REG_CLEAR 0x00
> +#define TSL258X_CNTL_ALS_INT_ENBL 0x10
> +#define TSL258X_CNTL_WAIT_TMR_ENBL 0x08
> +#define TSL258X_CNTL_ADC_ENBL 0x02
> +#define TSL258X_CNTL_PWRON 0x01
> +#define TSL258X_CNTL_ALSPON_ENBL 0x03
Define this in terms of PWRON and ADC_ENBL to make it clear what it is.

> +#define TSL258X_CNTL_INTALSPON_ENBL 0x13
also define this in terms of its sub parts.
> +
> +/* Skate status reg masks */
> +#define TSL258X_STA_ADCVALID 0x01
> +#define TSL258X_STA_ALSINTR 0x10
> +#define TSL258X_STA_ADCINTR 0x10
> +
> +/* Lux constants */
> +#define MAX_LUX 65535
Err. Rename that unless it really does mean 65535 lux
> +
> +enum {
> + TAOS_CHIP_UNKNOWN = 0, TAOS_CHIP_WORKING = 1, TAOS_CHIP_SLEEP = 2
> +} TAOS_CHIP_WORKING_STATUS;
> +
> +/* Per-device data */
> +struct taos_als_info {
> + u16 als_ch0;
> + u16 als_ch1;
> + u16 lux;
> +};
> +
> +struct taos_settings {
> + int als_time;
> + int als_gain;
> + int als_gain_trim;
> + int als_cal_target;
> +};
> +
> +struct tsl258x_chip {
> + struct mutex als_mutex;
> + struct i2c_client *client;
> + struct iio_dev *iio_dev;
> + struct delayed_work update_lux;
> + unsigned int addr;
> + char taos_id;
> + char valid;
> + unsigned long last_updated;
> + struct taos_als_info als_cur_info;
> + struct taos_settings taos_settings;
> + int als_time_scale;
> + int als_saturation;
> + int taos_chip_status;
> + u8 taos_config[8];
> +};
> +
> +static int taos_i2c_read(struct i2c_client *client, u8 reg, u8 *val,
> + unsigned int len);
> +static int taos_i2c_write_command(struct i2c_client *client, u8 reg);
> +
> +/*
> + * Initial values for device - this values can/will be changed by driver.
> + * and applications as needed.
> + * These values are dynamic.
> + */
> +static const u8 taos_config[8] = {
> + 0x00, 0xee, 0x00, 0x03, 0x00, 0xFF, 0xFF, 0x00
> +}; /* cntrl atime intC Athl0 Athl1 Athh0 Athh1 gain */
> +
> +struct taos_lux {
> + unsigned int ratio;
> + unsigned int ch0;
> + unsigned int ch1;
> +};
> +
> +/* This structure is intentionally large to accommodate updates via sysfs. */
> +/* Sized to 11 = max 10 segments + 1 termination segment */
Any chance of two sensors on one device, each of which has different
values for this?

> +struct taos_lux taos_device_lux[11] = {
> + { 9830, 8520, 15729 },
> + { 12452, 10807, 23344 },
> + { 14746, 6383, 11705 },
> + { 17695, 4063, 6554 },
> +};
> +
> +struct taos_lux taos_lux;
> +
> +struct gainadj {
> + s16 ch0;
> + s16 ch1;
> +};
> +
> +/* Index = (0 - 3) Used to validate the gain selection index */
> +static const struct gainadj gainadj[] = {
> + { 1, 1 },
> + { 8, 8 },
> + { 16, 16 },
That's 'interesting'. This will make the calibscale discussion above more
complex. I guess no userspace is going to care about the precise internal
multipliers so a 'rough' value would probably do in that attribute. What
do you think?
> + { 107, 115 }
> +};
> +
> +/*
> + * Provides initial operational parameter defaults.
> + * These defaults may be changed through the device's sysfs files.
> + */
> +static void taos_defaults(struct tsl258x_chip *chip)
> +{
> + /* Operational parameters */
> + chip->taos_settings.als_time = 450;
> + /* must be a multiple of 50mS */
> + chip->taos_settings.als_gain = 2;
> + /* this is actually an index into the gain table */
> + /* assume clear glass as default */
> + chip->taos_settings.als_gain_trim = 1000;
> + /* default gain trim to account for aperture effects */
> + chip->taos_settings.als_cal_target = 130;
> + /* Known external ALS reading used for calibration */
> +
> + /* Initialize ALS data to defaults */
> + chip->als_cur_info.als_ch0 = 0;
> + chip->als_cur_info.als_ch1 = 0;
> + chip->als_cur_info.lux = 0;
Already zero via the memset (soon to be kzalloc) hence don't bother
setting these three.
> +}
> +
> +/*
> + * Read a number of bytes starting at register (reg) location.
> + * Return 0, or i2c_smbus_write_byte ERROR code.
> + */
> +static int
> +taos_i2c_read(struct i2c_client *client, u8 reg, u8 *val, unsigned int len)
> +{
> + int ret;
> + int i;
> +
> + for (i = 0; i < len; i++) {
> + /* select register to write */
> + ret = i2c_smbus_write_byte(client, (TSL258X_CMD_REG | reg));
> + if (ret < 0) {
> + dev_err(&client->dev, "taos_i2c_read failed to write"
> + " register %x\n", reg);
> + return ret;
> + }
> + /* read the data */
> + *val = i2c_smbus_read_byte(client);
I'd use val[i] without this increment for clarity.
> + val++;
> + if ((reg & 0x1f) == 0x1f)
Can this ever occcur in the driver? I would imagine it is a bug if it does
as you'll read back a different number of values than you expect to do.
If not it's an over enthusiastic bit of debug code so get rid of it.
> + break;
> + reg++;
> + }
> + return 0;
> +}
> +
> +/*
> + * This function is used to send a command to device command/control register
> + * All bytes sent using this command have their MSBit set - it's a command!
> + * Return 0, or i2c_smbus_write_byte error code.
> + */
> +static int taos_i2c_write_command(struct i2c_client *client, u8 reg)
> +{
> + int ret;
> +
> + /* write the data */
> + ret = i2c_smbus_write_byte(client, (reg |= TSL258X_CMD_REG));
> + if (ret < 0) {
> + dev_err(&client->dev, "FAILED: i2c_smbus_write_byte\n");
> + return ret;
> + }
> + return 0;
> +}
> +
> +/*
> + * Reads and calculates current lux value.
> + * The raw ch0 and ch1 values of the ambient light sensed in the last
> + * integration cycle are read from the device.
> + * Time scale factor array values are adjusted based on the integration time.
> + * The raw values are multiplied by a scale factor, and device gain is obtained
> + * using gain index. Limit checks are done next, then the ratio of a multiple
> + * of ch1 value, to the ch0 value, is calculated. The array taos_device_lux[]
> + * declared above is then scanned to find the first ratio value that is just
> + * above the ratio we just calculated. The ch0 and ch1 multiplier constants in
> + * the array are then used along with the time scale factor array values, to
> + * calculate the lux.
> + */
> +static int taos_get_lux(struct i2c_client *client)
> +{
> + u32 ch0, ch1; /* separated ch0/ch1 data from device */
> + u32 lux; /* raw lux calculated from device data */
And here we have a great example of why lux is a bad name for this.
lux could only ever have units of lux.
> + u32 ratio;
> + u8 buf[5];
> + struct taos_lux *p;
> + struct tsl258x_chip *chip = i2c_get_clientdata(client);
> + int i, ret;
> + u32 ch0lux = 0;
> + u32 ch1lux = 0;
> +
> + if (mutex_trylock(&chip->als_mutex) == 0) {
> + dev_info(&client->dev, "taos_get_lux device is busy\n");
> + return chip->als_cur_info.lux; /* busy, so return LAST VALUE */
> + }
> +
> + if (chip->taos_chip_status != TAOS_CHIP_WORKING) {
> + /* device is not enabled */
> + dev_err(&client->dev, "taos_get_lux device is not enabled\n");
> + ret = -ENODEV;
-EBUSY probably. The device exists, it's just turned off.

> + goto out_unlock;
> + }
> +
> + ret = taos_i2c_read(client, (TSL258X_CMD_REG), &buf[0], 1);
> + if (ret < 0) {
> + dev_err(&client->dev, "taos_get_lux failed to read CMD_REG\n");
> + goto out_unlock;
> + }
> + /* is data new & valid */
> + if (!(buf[0] & TSL258X_STA_ADCINTR)) {
> + dev_err(&client->dev, "taos_get_lux data not valid\n");
I'd error out at this point. Something has gone wrong and you want to
indicate it to your userspace code.
> + ret = chip->als_cur_info.lux; /* return LAST VALUE */
> + goto out_unlock;
> + }
> +
> + for (i = 0; i < 4; i++) {
> + int reg = TSL258X_CMD_REG | (TSL258X_ALS_CHAN0LO + i);
> + ret = taos_i2c_read(client, reg, &buf[i], 1);
> + if (ret < 0) {
> + dev_err(&client->dev, "taos_get_lux failed to read"
> + " register %x\n", reg);
> + goto out_unlock;
> + }
> + }
> +
> + /* clear status, really interrupt status (interrupts are off), but
> + * we use the bit anyway */
> + ret = taos_i2c_write_command(client,
> + TSL258X_CMD_REG | TSL258X_CMD_SPL_FN | TSL258X_CMD_ALS_INTCLR);
> + if (ret < 0) {
> + dev_err(&client->dev,
This is the one case where checkpatch warnings should be ignored.
Please keep strings like this on a single line as people who see them
in a log will grep for them in the source code. Artificial breaks
like this make them a lot harder to find!

> + "taos_i2c_write_command failed in "
> + "taos_get_lux, err = %d\n", ret);
> + goto out_unlock; /* have no data, so return failure */
> + }
> +
> + /* extract ALS/lux data */
Should be the relevant endian conversion function. be16tocpu or similar
(haven't thought about which). That way it's free on one endianness of
machine.
> + ch0 = (buf[1] << 8) | buf[0];
> + ch1 = (buf[3] << 8) | buf[2];
> +
> + chip->als_cur_info.als_ch0 = ch0;
> + chip->als_cur_info.als_ch1 = ch1;
> +
> + if ((ch0 >= chip->als_saturation) || (ch1 >= chip->als_saturation))
> + goto return_max;
> +
> + if (ch0 == 0) {
> + /* have no data, so return LAST VALUE */
> + ret = chip->als_cur_info.lux = 0;
> + goto out_unlock;
> + }
> + /* calculate ratio */
> + ratio = (ch1 << 15) / ch0;
> + /* convert to unscaled lux using the pointer to the table */
> + for (p = (struct taos_lux *) taos_device_lux;
> + p->ratio != 0 && p->ratio < ratio; p++)
> + ;
> +
> + if (p->ratio == 0) {
> + lux = 0;
> + } else {
> + ch0lux = ((ch0 * p->ch0) +
> + (gainadj[chip->taos_settings.als_gain].ch0 >> 1))
> + / gainadj[chip->taos_settings.als_gain].ch0;
> + ch1lux = ((ch1 * p->ch1) +
> + (gainadj[chip->taos_settings.als_gain].ch1 >> 1))
> + / gainadj[chip->taos_settings.als_gain].ch1;
> + lux = ch0lux - ch1lux;
> + }
> +
> + /* note: lux is 31 bit max at this point */
> + if (ch1lux > ch0lux) {
> + dev_dbg(&client->dev, "No Data - Return last value\n");
Again, do we want userspace to know the sensor isn't returning valid values?
> + ret = chip->als_cur_info.lux = 0;
> + goto out_unlock;
> + }
> +
> + /* adjust for active time scale */
> + if (chip->als_time_scale == 0)
> + lux = 0;
> + else
> + lux = (lux + (chip->als_time_scale >> 1)) /
> + chip->als_time_scale;
> +
> + /* adjust for active gain scale */
> + lux >>= 13; /* tables have factor of 8192 builtin for accuracy */
> + lux = (lux * chip->taos_settings.als_gain_trim + 500) / 1000;
> + if (lux > MAX_LUX) { /* check for overflow */
> +return_max:
> + lux = MAX_LUX;
Really the right thing to do? Surely you want to return an out of range
error? Perhaps ERANGE so userspace knows the value is garbage.
> + }
> +
> + /* Update the structure with the latest VALID lux. */
> + chip->als_cur_info.lux = lux;
> + ret = lux;
> +
> +out_unlock:
> + mutex_unlock(&chip->als_mutex);
> + return ret;
> +}
> +
> +/*
> + * Obtain single reading and calculate the als_gain_trim (later used
> + * to derive actual lux).
> + * Return updated gain_trim value.
> + */
> +int taos_als_calibrate(struct i2c_client *client)
> +{
> + struct tsl258x_chip *chip = i2c_get_clientdata(client);
> + u8 reg_val;
> + unsigned int gain_trim_val;
> + int ret;
> + int lux_val;
> +
> + ret = i2c_smbus_write_byte(client, (TSL258X_CMD_REG | TSL258X_CNTRL));
> + if (ret < 0) {
> + dev_err(&client->dev, "taos_als_calibrate failed to reach the"
Again, don't break this sort of string up however much checkpatch rants at you.
> + " CNTRL register, ret=%d\n", ret);
> + return ret;
> + }
> +
> + reg_val = i2c_smbus_read_byte(client);
> + if ((reg_val & (TSL258X_CNTL_ADC_ENBL | TSL258X_CNTL_PWRON))
> + != (TSL258X_CNTL_ADC_ENBL | TSL258X_CNTL_PWRON)) {
> + dev_err(&client->dev, "taos_als_calibrate failed because the"
> + " device is not powered on with ADC enabled\n");
> + return -ENODATA;
> + }
> +
> + ret = i2c_smbus_write_byte(client, (TSL258X_CMD_REG | TSL258X_STATUS));
> + if (ret < 0) {
> + dev_err(&client->dev, "taos_als_calibrate failed to reach the"
> + " STATUS register, ret=%d\n", ret);
> + return ret;
> + }
> + reg_val = i2c_smbus_read_byte(client);
> +
> + if ((reg_val & TSL258X_STA_ADCVALID) != TSL258X_STA_ADCVALID) {
> + dev_err(&client->dev, "taos_als_calibrate failed because the"
> + " STATUS did not indicate ADC valid.\n");
> + return -ENODATA;
> + }
> + lux_val = taos_get_lux(client);
> + if (lux_val < 0) {
> + dev_err(&client->dev, "taos_als_calibrate failed to get lux\n");
> + return lux_val;
> + }
> + gain_trim_val = (unsigned int) (((chip->taos_settings.als_cal_target)
> + * chip->taos_settings.als_gain_trim) / lux_val);
> +
> + dev_info(&client->dev, "taos_settings.als_cal_target = %d\n"
> + "taos_settings.als_gain_trim = %d\nlux_val = %d\n",
> + chip->taos_settings.als_cal_target,
> + chip->taos_settings.als_gain_trim,
> + lux_val);
> +
> + if ((gain_trim_val < 250) || (gain_trim_val > 4000)) {
> + dev_err(&client->dev, "taos_als_calibrate failed because"
> + "trim_val of %d is out of range\n", gain_trim_val);
> + return -ENODATA;
> + }
> + chip->taos_settings.als_gain_trim = (int) gain_trim_val;
> +
> + return (int) gain_trim_val;
> +}
> +
> +/*
> + * Turn the device on.
> + * Configuration must be set before calling this function.
> + */
> +static int taos_chip_on(struct i2c_client *client)
> +{
> + int i;
> + int ret = 0;
> + u8 *uP;
> + u8 utmp;
> + int als_count;
> + int als_time;
> + struct tsl258x_chip *chip = i2c_get_clientdata(client);
> +
and?
> + /* and make sure we're not already on */
> + if (chip->taos_chip_status == TAOS_CHIP_WORKING) {
> + /* if forcing a register update - turn off, then on */
> + dev_info(&client->dev, "device is already enabled\n");
Not sure what the right error is here, but should be more specific than
that.
> + return -1;
> + }
> +
> + /* determine als integration regster */
> + als_count = (chip->taos_settings.als_time * 100 + 135) / 270;
> + if (als_count == 0)
> + als_count = 1; /* ensure at least one cycle */
> +
> +
> + /* convert back to time (encompasses overrides) */
> + als_time = (als_count * 27 + 5) / 10;
> + chip->taos_config[TSL258X_ALS_TIME] = 256 - als_count;
> +
> +
Bonus blank lines. One is plenty to break up code.
> + /* Set the gain based on taos_settings struct */
> + chip->taos_config[TSL258X_GAIN] = chip->taos_settings.als_gain;
> +
> +
> + /* set globals re scaling and saturation */
They aren't globals
> + chip->als_saturation = als_count * 922; /* 90% of full scale */
> + chip->als_time_scale = (als_time + 25) / 50;
> +
> + /* SKATE Specific power-on / adc enable sequence
> + * Power on the device 1st. */
> + utmp = TSL258X_CNTL_PWRON;
> + ret = i2c_smbus_write_byte_data(client, TSL258X_CMD_REG | TSL258X_CNTRL,
> + utmp);
> + if (ret < 0) {
> + dev_err(&client->dev, "taos_chip_on failed on CNTRL reg.\n");
> + return -1;
> + }
> +
> + /* Use the following shadow copy for our delay before enabling ADC.
> + * Write all the registers. */
> + for (i = 0, uP = chip->taos_config; i < TAOS_REG_MAX; i++) {
> + ret = i2c_smbus_write_byte_data(client, TSL258X_CMD_REG + i,
> + *uP++);
> + if (ret < 0) {
> + dev_err(&client->dev,
> + "taos_chip_on failed on reg %d.\n", i);
> + return -1;
> + }
> + }
> +
> + mdelay(3);
> + /* NOW enable the ADC
> + * initialize the desired mode of operation */
> + utmp = TSL258X_CNTL_PWRON | TSL258X_CNTL_ADC_ENBL;
> + ret = i2c_smbus_write_byte_data(client, TSL258X_CMD_REG | TSL258X_CNTRL,
> + utmp);
> + if (ret < 0) {
> + dev_err(&client->dev, "taos_chip_on failed on 2nd CTRL reg.\n");
> + return -1;
> + }
> + chip->taos_chip_status = TAOS_CHIP_WORKING;
Comment is rather obvious...

> + return ret; /* returns result of last i2cwrite */
> +}
> +
> +/* Turn the device OFF. */
> +static int taos_chip_off(struct i2c_client *client)
> +{
> + struct tsl258x_chip *chip = i2c_get_clientdata(client);
> + int ret;
> + u8 utmp;
> +
> + /* turn device off */
> + chip->taos_chip_status = TAOS_CHIP_SLEEP;
> + utmp = 0x00;
> + ret = i2c_smbus_write_byte_data(client, TSL258X_CMD_REG | TSL258X_CNTRL,
> + utmp);
> + return ret;
> +}
> +
> +/* Sysfs Interface Functions */
> +static ssize_t taos_device_id(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + return sprintf(buf, "%s\n", DEVICE_ID);
> +}
> +
> +static ssize_t taos_power_state_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> +
> + return sprintf(buf, "%d\n", chip->taos_chip_status);
> +}
> +
> +static ssize_t taos_power_state_store(struct device *dev,
> + struct device_attribute *attr, const char *buf, size_t len)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> + unsigned long value;
> +
> + if (strict_strtoul(buf, 0, &value))
> + return -EINVAL;
> +
> + if (value == 0)
> + taos_chip_off(chip->client);
> + else
> + taos_chip_on(chip->client);
> +
> + return len;
> +}
> +
> +static ssize_t taos_gain_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> +
> + return sprintf(buf, "%d\n", chip->taos_settings.als_gain);
> +}
> +
> +static ssize_t taos_gain_store(struct device *dev,
> + struct device_attribute *attr, const char *buf, size_t len)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> + unsigned long value;
> + if (strict_strtoul(buf, 0, &value))
> + return -EINVAL;
> + if (value) {
> + if (value > 4) {
> + dev_err(dev, "Invalid Gain Index\n");
> + return -1;
EINVAL
> + } else {
> + chip->taos_settings.als_gain = value;
> + }
So this sets the value in the local cache. When does it get written to the
device?
> + }
> + return len;
> +}
> +
> +static ssize_t taos_als_time_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> +
> + return sprintf(buf, "%d\n", chip->taos_settings.als_time);
> +}
> +
> +static ssize_t taos_als_time_store(struct device *dev,
> + struct device_attribute *attr, const char *buf, size_t len)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> + unsigned long value;
> +
> + if (strict_strtoul(buf, 0, &value))
> + return -EINVAL;
> +
> + if (value)
> + chip->taos_settings.als_time = value;
else? It's not been sucessfuly set so return -EINVAL
> +
> + return len;
> +}
> +
> +static ssize_t taos_als_trim_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> +
> + return sprintf(buf, "%d\n", chip->taos_settings.als_gain_trim);
> +}
> +
> +static ssize_t taos_als_trim_store(struct device *dev,
> + struct device_attribute *attr, const char *buf, size_t len)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> + unsigned long value;
> +
> + if (strict_strtoul(buf, 0, &value))
> + return -EINVAL;
> +
> + if (value)
> + chip->taos_settings.als_gain_trim = value;
else return -EINVAL
> +
> + return len;
> +}
> +
> +static ssize_t taos_als_cal_target_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> +
> + return sprintf(buf, "%d\n", chip->taos_settings.als_cal_target);
> +}
> +
> +static ssize_t taos_als_cal_target_store(struct device *dev,
> + struct device_attribute *attr, const char *buf, size_t len)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> + unsigned long value;
> +
> + if (strict_strtoul(buf, 0, &value))
> + return -EINVAL;
> +
> + if (value)
> + chip->taos_settings.als_cal_target = value;
again, else return -EINVAL; Userspace really wants to know this failed.
> +
> + return len;
> +}
> +
> +static ssize_t taos_lux_show(struct device *dev, struct device_attribute *attr,
> + char *buf)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> + int lux = 0;
no need to assign.
> +
> + lux = taos_get_lux(chip->client);
> +
> + return sprintf(buf, "%d\n", lux);
> +}
> +
> +static ssize_t taos_do_calibrate(struct device *dev,
> + struct device_attribute *attr, const char *buf, size_t len)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> + unsigned long value;
> +
> + if (strict_strtoul(buf, 0, &value))
> + return -EINVAL;
> +
> + if (value == 1)
> + taos_als_calibrate(chip->client);
else return -EINVAL;
> +
> + return len;
> +}
> +
> +static ssize_t taos_luxtable_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + int i;
> + int offset = 0;
> +
> + for (i = 0; i < ARRAY_SIZE(taos_device_lux); i++) {
> + offset += sprintf(buf + offset, "%d,%d,%d,",
> + taos_device_lux[i].ratio,
> + taos_device_lux[i].ch0,
> + taos_device_lux[i].ch1);
> + if (taos_device_lux[i].ratio == 0) {
> + /* We just printed the first "0" entry.
> + * Now get rid of the extra "," and break. */
> + offset--;
> + break;
> + }
> + }
> +
> + offset += sprintf(buf + offset, "\n");
> + return offset;
> +}
> +
> +static ssize_t taos_luxtable_store(struct device *dev,
> + struct device_attribute *attr, const char *buf, size_t len)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> +#define MAX_LUX_TABLE_FIELDS 33
I'd loose this define.
> + int value[MAX_LUX_TABLE_FIELDS];
> + int n;
> +
> + get_options(buf, ARRAY_SIZE(value), value);
> +
> + /* We now have an array of ints starting at value[1], and
> + * enumerated by value[0].
> + * We expect each group of three ints is one table entry,
> + * and the last table entry is all 0.
> + */
> + n = value[0];
prefer to see ARRAY_SIZE(value) than the define.
> + if ((n % 3) || n < 6 || n > (MAX_LUX_TABLE_FIELDS - 3)) {
> + dev_info(dev, "LUX TABLE INPUT ERROR 1 Value[0]=%d\n", n);
> + return -EINVAL;
> + }
> + if ((value[(n - 2)] | value[(n - 1)] | value[n]) != 0) {
> + dev_info(dev, "LUX TABLE INPUT ERROR 2 Value[0]=%d\n", n);
> + return -EINVAL;
> + }
> +
> + if (chip->taos_chip_status == TAOS_CHIP_WORKING)
> + taos_chip_off(chip->client);
> +
> + /* Zero out the table */
> + memset(taos_device_lux, 0, sizeof(taos_device_lux));
> + memcpy(taos_device_lux, &value[1], (value[0] * 4));
> +
> + taos_chip_on(chip->client);
> +
> + return len;
> +}
> +
> +static u8 reg_index;
> +
As stated above these need to go before we take this driver.
> +/* Sets a pointer to a register for R/W via sysfs */
> +static ssize_t taos_reg_offset_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + return sprintf(buf, "%d\n", reg_index);
> + return 0;
> +}
> +
> +static ssize_t taos_reg_offset_store(struct device *dev,
> + struct device_attribute *attr, const char *buf, size_t len)
> +{
> + unsigned long value;
> + if (strict_strtoul(buf, 0, &value))
> + return -EINVAL;
> +
> + if (value > MAX_DEVICE_REGS) {
> + dev_err(dev, "register offset exceeds MAX\n");
> + return -1;
> + } else {
> + reg_index = value;
> + }
> +return len;
> +}
> +
> +/* R/W a register for R/W via sysfs */
> +static ssize_t taos_reg_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> +
> + u8 value = 0;
> + int ret = 0;
> +
> + ret = i2c_smbus_write_byte(chip->client,
> + (TSL258X_CMD_REG | reg_index));
> + if (ret < 0) {
> + dev_err(dev, "i2c_smbus_write_byte to cmd reg failed "
> + "in taos_reg_offset_show(), err = %d\n", ret);
> + return ret;
> + }
> + value = i2c_smbus_read_byte(chip->client);
> + return sprintf(buf, "%d\n", value);
> +
> +return 0;
> +}
> +
> +static ssize_t taos_reg_store(struct device *dev,
> + struct device_attribute *attr, const char *buf, size_t len)
> +{
> + struct iio_dev *indio_dev = dev_get_drvdata(dev);
> + struct tsl258x_chip *chip = indio_dev->dev_data;
> +
> + unsigned long value = 0;
> + int ret = 0;
> +
> + if (strict_strtoul(buf, 0, &value))
> + return -EINVAL;
> +
> + ret = i2c_smbus_write_byte_data(chip->client,
> + (TSL258X_CMD_REG | reg_index), value);
> + if (ret < 0) {
> + dev_err(dev, "i2c_smbus_write_byte_data failed in "
> + "taos_reg_store()\n");
> + return ret;
> + }
> +
> +return len;
> +}
> +
> +static DEVICE_ATTR(name, S_IRUGO, taos_device_id, NULL);
> +static DEVICE_ATTR(device_state, S_IRUGO | S_IWUSR,
> + taos_power_state_show, taos_power_state_store);
> +static DEVICE_ATTR(als_gain, S_IRUGO | S_IWUSR,
> + taos_gain_show, taos_gain_store);
> +static DEVICE_ATTR(als_time, S_IRUGO | S_IWUSR,
> + taos_als_time_show, taos_als_time_store);
> +static DEVICE_ATTR(als_trim, S_IRUGO | S_IWUSR,
> + taos_als_trim_show, taos_als_trim_store);
> +static DEVICE_ATTR(als_target, S_IRUGO | S_IWUSR,
> + taos_als_cal_target_show, taos_als_cal_target_store);
> +static DEVICE_ATTR(lux, S_IRUGO, taos_lux_show, NULL);
> +static DEVICE_ATTR(calibrate, S_IWUSR, NULL, taos_do_calibrate);
> +static DEVICE_ATTR(lux_table, S_IRUGO | S_IWUSR,
> + taos_luxtable_show, taos_luxtable_store);
> +static DEVICE_ATTR(reg_offset, S_IRUGO | S_IWUSR,
> + taos_reg_offset_show,
> + taos_reg_offset_store);
> +static DEVICE_ATTR(reg, S_IRUGO | S_IWUSR,
> + taos_reg_show,
> + taos_reg_store);
> +
> +
> +static struct attribute *sysfs_attrs_ctrl[] = {
> + &dev_attr_name.attr,
> + &dev_attr_device_state.attr,
> + &dev_attr_als_gain.attr,
> + &dev_attr_als_time.attr,
> + &dev_attr_als_trim.attr,
> + &dev_attr_als_target.attr,
> + &dev_attr_lux.attr,
> + &dev_attr_calibrate.attr,
> + &dev_attr_lux_table.attr,
Spaces instead of tab here.
> + &dev_attr_reg_offset.attr,
> + &dev_attr_reg.attr,
> + NULL
> +};
> +
> +static struct attribute_group tsl258x_attribute_group = {
> + .attrs = sysfs_attrs_ctrl,
> +};
> +
> +/* Use the default register values to identify the Taos device */
> +static int taos_skate_device(unsigned char *bufp)
> +{
> + if (((bufp[TSL258X_CHIPID] & 0xf0) == 0x90))
> + /* tsl258x */
> + return 1;
> + /* else unknown */
> + return 0;
> +}
> +
> +/*
> + * Client probe function - When a valid device is found, the driver's device
> + * data structure is updated, and initialization completes successfully.
> + */
> +static int __devinit taos_probe(struct i2c_client *clientp,
> + const struct i2c_device_id *idp)
> +{
> + int i, ret = 0;
> + unsigned char buf[MAX_DEVICE_REGS];
> + static struct tsl258x_chip *chip;
> +
> + if (!i2c_check_functionality(clientp->adapter,
> + I2C_FUNC_SMBUS_BYTE_DATA)) {
> + dev_err(&clientp->dev,
> + "taos_probe() - i2c smbus byte data "
> + "functions unsupported\n");
> + return -EOPNOTSUPP;
> + }
> + if (!i2c_check_functionality(clientp->adapter,
> + I2C_FUNC_SMBUS_WORD_DATA)) {
> + dev_warn(&clientp->dev,
> + "taos_probe() - i2c smbus word data "
> + "functions unsupported\n");
> + }
> + if (!i2c_check_functionality(clientp->adapter,
> + I2C_FUNC_SMBUS_BLOCK_DATA)) {
> + dev_err(&clientp->dev,
> + "taos_probe() - i2c smbus block data "
> + "functions unsupported\n");
> + }
> +
> + chip = kmalloc(sizeof(struct tsl258x_chip), GFP_KERNEL);
> + if (!chip) {
> + dev_err(&clientp->dev, "taos_device_drvr: kmalloc for "
> + "struct tsl258x_chip failed in taos_probe()\n");
> + return -ENOMEM;
> + }
> + memset(chip, 0, sizeof(struct tsl258x_chip));
Use kzalloc instead of kmalloc then you don't need the memset.

> + chip->client = clientp;
> + i2c_set_clientdata(clientp, chip);
> +
> + mutex_init(&chip->als_mutex);
> + chip->taos_chip_status = TAOS_CHIP_UNKNOWN; /* uninitialized to start */
> + memcpy(chip->taos_config, taos_config, sizeof(chip->taos_config));
> +
> + for (i = 0; i < MAX_DEVICE_REGS; i++) {
> + ret = i2c_smbus_write_byte(clientp,
> + (TSL258X_CMD_REG | (TSL258X_CNTRL + i)));
> + if (ret < 0) {
> + dev_err(&clientp->dev, "i2c_smbus_write_byte() to cmd "
> + "reg failed in taos_probe(), err = %d\n", ret);
> + goto fail1;
> + }
> + buf[i] = i2c_smbus_read_byte(clientp);
> + }
> + if (!taos_skate_device(buf)) {
> + dev_info(&clientp->dev, "i2c device found but does not match "
> + "expected id in taos_probe()\n");
> + goto fail1;
> + } else {
> + dev_info(&clientp->dev, "i2c device match in probe\n");
> + }
> + ret = i2c_smbus_write_byte(clientp, (TSL258X_CMD_REG | TSL258X_CNTRL));
> + if (ret < 0) {
> + dev_err(&clientp->dev, "i2c_smbus_write_byte() to cmd reg "
> + "failed in taos_probe(), err = %d\n", ret);
> + goto fail1;
> + }
> + chip->valid = 0;
> +
> + chip->iio_dev = iio_allocate_device();
> + if (!chip->iio_dev) {
> + ret = -ENOMEM;
> + dev_err(&clientp->dev, "iio allocation failed\n");
> + goto fail1;
> + }
> +
> + chip->iio_dev->attrs = &tsl258x_attribute_group;
> + chip->iio_dev->dev.parent = &clientp->dev;
> + chip->iio_dev->dev_data = (void *)(chip);
> + chip->iio_dev->driver_module = THIS_MODULE;
> + chip->iio_dev->modes = INDIO_DIRECT_MODE;
> + ret = iio_device_register(chip->iio_dev);
> + if (ret) {
> + dev_err(&clientp->dev, "iio registration failed\n");
> + goto fail1;
> + }
> +
> + /* Load up the V2 defaults (these are hard coded defaults for now) */
> + taos_defaults(chip);
> +
> + /* Make sure the chip is on */
> + taos_chip_on(clientp);
> +
> + dev_info(&clientp->dev, "Light sensor found.\n");
> + return 0;
> +
> +fail1:
> + kfree(chip);
> +
> + return ret;
> +}
> +
> +static int __devexit taos_remove(struct i2c_client *client)
> +{
> + struct tsl258x_chip *chip = i2c_get_clientdata(client);
> +
> + iio_device_unregister(chip->iio_dev);
> +
> + kfree(chip);
> + return 0;
> +}
> +
> +static struct i2c_device_id taos_idtable[] = {
> + { DEVICE_ID, 0 },
> + {}
Please can we have an explicit list if ID's here. If a person has
a tsl2580 then they'll want to say that in their board file.

On that note, I skipped this originally as there were bigger fish
to fry, but can we be sure that there will never be a value of x
that this driver won't work for? If not, please follow convention
and pick your favourite part number from the range and replace all
x's in the driver appropriately. Too many part manufacturers have
really weird naming schemes that tend to break wild cards like this!


> +};
> +MODULE_DEVICE_TABLE(i2c, taos_idtable);
> +
> +/* Driver definition */
> +static struct i2c_driver taos_driver = {
> + .driver = {
> + .name = "tsl258x",
> + },
> + .id_table = taos_idtable,
> + .probe = taos_probe,
> + .remove = __devexit_p(taos_remove),
> +};
> +
> +static int __init taos_init(void)
> +{
> + return i2c_add_driver(&taos_driver);
> +}
> +
> +static void __exit taos_exit(void)
> +{
> + i2c_del_driver(&taos_driver);
> +}
> +
> +module_init(taos_init);
> +module_exit(taos_exit);
> +
> +MODULE_AUTHOR("J. August Brenner<jbrenner@xxxxxxxxxxx>");
> +MODULE_DESCRIPTION("TAOS tsl258x ambient light sensor driver");
> +MODULE_LICENSE("GPL");
> +

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/