Hauppauge WinTV-HVR-1120 on Unbuntu 10.04

[fabio tirapelle]

 Yesterday I have installed (added not substituted) a new tuner: Hauppauge 
Nova-T Stick 3
 Today the  WinTV-HVR-1120 doesn't works.
 I attach my /var/log/messages

 lsusb

 Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
 Bus 003 Device 002: ID 15c2:0036 SoundGraph Inc.
 Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
 Bus 002 Device 002: ID 2040:7070 Hauppauge Nova-T Stick 3
 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


 lscpi

 00:00.0 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller
 (rev a2)
 00:01.0 ISA bridge: nVidia Corporation MCP78S [GeForce 8200] LPC Bridge (rev 
a2)
 00:01.1 SMBus: nVidia Corporation MCP78S [GeForce 8200] SMBus (rev a1)
 00:01.2 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller
 (rev a1)
 00:01.3 Co-processor: nVidia Corporation MCP78S [GeForce 8200] Co-Processor 
(rev
 a2)
 00:01.4 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller
 (rev a1)
 00:02.0 USB Controller: nVidia Corporation MCP78S [GeForce 8200] OHCI USB 1.1
 Controller (rev a1)
 00:02.1 USB Controller: nVidia Corporation MCP78S [GeForce 8200] EHCI USB 2.0
 Controller (rev a1)
 00:04.0 USB Controller: nVidia Corporation MCP78S [GeForce 8200] OHCI USB 1.1
 Controller (rev a1)
 00:04.1 USB Controller: nVidia Corporation MCP78S [GeForce 8200] EHCI USB 2.0
 Controller (rev a1)
 00:06.0 IDE interface: nVidia Corporation MCP78S [GeForce 8200] IDE (rev a1)
 00:07.0 Audio device: nVidia Corporation MCP72XE/MCP72P/MCP78U/MCP78S High
 Definition Audio (rev a1)
 00:08.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Bridge (rev 
a1)
 00:09.0 IDE interface: nVidia Corporation MCP78S [GeForce 8200] SATA Controller
 (non-AHCI mode) (rev a2)
 00:0a.0 Ethernet controller: nVidia Corporation MCP77 Ethernet (rev a2)
 00:0b.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express Bridge
 (rev a1)
 00:10.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express Bridge
 (rev a1)
 00:12.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express Bridge
 (rev a1)
 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
 HyperTransport Technology Configuration
 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address
 Map
 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM
 Controller
 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
 Miscellaneous Control
 01:06.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135
 Video Broadcast Decoder (rev d1)
 01:07.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip 
/
 Technisat SkyStar2 DVB card (rev 02)
 02:00.0 VGA compatible controller: nVidia Corporation C77 [GeForce 8200] (rev
 a2)


> ----- Messaggio originale -----
> > Da: Bjorn  Helgaas <bjorn.helgaas@xxxxxx>
> > A: fabio  tirapelle <ftirapelle@xxxxxxxx>
> > Cc: linux-kernel@xxxxxxxxxxxxxxx;  Michael Krufky <mkrufky@xxxxxxxxxxxxxx>
> >  Inviato: Mer 13 ottobre 2010, 21:54:31
> > Oggetto: Re: Hauppauge  WinTV-HVR-1120 on Unbuntu 10.04
> > 
> > On Wednesday, October 13, 2010  01:02:11 pm fabio tirapelle wrote:
> > > After  upgrading from  Ubuntu 9.10 to Ubuntu 10.04 my Hauppauge 
>WinTV-HVR-1120 
>
> >
> >  >  (sometimes) doesn't work correctly.
> > > I get random the  following  errors:
> > > 
> > > tda18271_write_regs: ERROR:  idx = 0x5, len = 1,  i2c_transfer returned: 
-5
> > > tda18271_init:  error -5 on line 826
> > >  tda18271_tune: error -5 on line  904
> > > tda18271_set_params: error -5 on  line 985
> > 
> > I cc'd Michael since he made several recent tda18271   changes.
> > 
> > This page: http://cvs.linuxtv.org/wiki/index.php/Zolid_Hybrid_TV_Tuner
> >  suggests  that the card might work, despite the error messages.   Does
> > yours  work?
> > 
> > I see that tda18271_write_regs()  uses i2c_transfer(), which uses  the
> > adap->algo->master_xfer  function pointer, but I don't know enough  to
> > figure out which  master_xfer implementation might be used on  your
> > system.  A  complete dmesg log and lspci output might have a  hint.
> > 
> >  Can you reproduce this on an upstream kernel?  It would be  good  to
> > make sure that it's not something introduced by an Ubuntu patch   or
> > fixed since the Ubuntu kernel snapshot.
> > 
> >  Bjorn
> > 
> > > Part of  dmesg of 11-OCT-2010
> > > 
> > > [   53.216153] DVB: registering new  adapter  (saa7133[0])
> > > [   53.216156] DVB: registering adapter 2   frontend 0 (NXP TDA10048HN 
> >DVB-T)...
> > > [    53.840013]  tda10048_firmware_upload: waiting for firmware upload 
> >  >  (dvb-fe-tda10048-1.0.fw)...
> > > [   53.840019] saa7134  0000:01:06.0:  firmware: requesting 
> >dvb-fe-tda10048-1.0.fw
> >  > [   53.880505]  tda10048_firmware_upload: firmware read 24878  bytes.
> > > [   53.880509]  tda10048_firmware_upload: firmware  uploading
> > > [   58.280136]  tda10048_firmware_upload:  firmware uploaded
> > > [   59.024537]  tda18271_write_regs:  ERROR: idx = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned:   -5
> > > [   59.024541] tda18271c2_rf_tracking_filters_correction:  error  -5 on 
>line 
>
> >264
> > > [   59.420153]  tda18271_write_regs: ERROR: idx =  0x5, len = 1, 
>i2c_transfer 
>
> 
> >  > returned: -5
> > > [   59.420157]  tda18271_toggle_output:  error -5 on line 47
> > > [   91.004019]  Clocksource tsc  unstable (delta = -295012684 ns)
> > > [  256.293639]  eth0:  link up.
> > > [  256.294750] ADDRCONF(NETDEV_CHANGE): eth0:  link  becomes ready
> > > [  263.523498] eth0: link  down.
> > > [   265.258740] eth0: link up.
> > > [   266.460026] eth0: no IPv6 routers  present
> > > [ 9869.636167]  tda18271_write_regs: ERROR: idx = 0x5, len = 1,  
>i2c_transfer 
>
> 
> >  > returned: -5
> > > [ 9869.636178] tda18271_init: error  -5 on  line 826
> > > [ 9872.636220] tda18271_write_regs: ERROR: idx = 0x5,  len  = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> > > [  9872.636232]  tda18271_toggle_output: error -5 on line 47
> > > [  9998.240167]  tda18271_write_regs: ERROR: idx = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned:  -5
> > > [ 9998.240178] tda18271_init:  error -5 on line 826
> > >  [10001.240179] tda18271_write_regs:  ERROR: idx = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> >  > [10001.240190] tda18271_toggle_output: error -5 on  line 47
> >  > 
> > > And this is the dmesg of today: even the same   errors.
> > > 
> > > [  741.252183] tda18271_init: error -5  on line  826
> > > [  741.252188] tda18271_tune: error -5 on  line 904
> > >  [  741.252193] tda18271_set_params: error -5 on  line 985
> > > [   742.268174] tda18271_write_regs: ERROR: idx =  0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> > > [   742.268184] tda18271_init: error -5 on  line 826
> > > [   742.268189] tda18271_tune: error -5 on line 904
> > >  [   742.268194] tda18271_set_params: error -5 on line 985
> > > [    743.284174] tda18271_write_regs: ERROR: idx = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> > > [  743.284184] tda18271_init:  error -5 on  line 826
> > > [  743.284190] tda18271_tune: error  -5 on line 904
> > >  [  743.284194] tda18271_set_params: error  -5 on line 985
> > > [   744.300169] tda18271_write_regs: ERROR: idx  = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> > > [   744.300180] tda18271_init: error -5 on  line 826
> > > [   744.300185] tda18271_tune: error -5 on line 904
> > >  [   744.300190] tda18271_set_params: error -5 on line 985
> > > [    745.320172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> > > [  745.320183] tda18271_init:  error -5 on  line 826
> > > [  745.320188] tda18271_tune: error  -5 on line 904
> > >  [  745.320193] tda18271_set_params: error  -5 on line 985
> > > [   746.336174] tda18271_write_regs: ERROR: idx  = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> > > [   746.336185] tda18271_init: error -5 on  line 826
> > > [   746.336190] tda18271_tune: error -5 on line 904
> > >  [   746.336195] tda18271_set_params: error -5 on line 985
> > > [    747.352170] tda18271_write_regs: ERROR: idx = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> > > [  747.352181] tda18271_init:  error -5 on  line 826
> > > [  747.352187] tda18271_tune: error  -5 on line 904
> > >  [  747.352192] tda18271_set_params: error  -5 on line 985
> > > [   748.368172] tda18271_write_regs: ERROR: idx  = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> > > [   748.368183] tda18271_init: error -5 on  line 826
> > > [   748.368188] tda18271_tune: error -5 on line 904
> > >  [   748.368193] tda18271_set_params: error -5 on line 985
> > > [    749.384179] tda18271_write_regs: ERROR: idx = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> > > [  749.384191] tda18271_init:  error -5 on  line 826
> > > [  749.384196] tda18271_tune: error  -5 on line 904
> > >  [  749.384202] tda18271_set_params: error  -5 on line 985
> > > [   750.400172] tda18271_write_regs: ERROR: idx  = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> > > [   750.400182] tda18271_init: error -5 on  line 826
> > > [   750.400188] tda18271_tune: error -5 on line 904
> > >  [   750.400194] tda18271_set_params: error -5 on line 985
> > > [    751.424170] tda18271_write_regs: ERROR: idx = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> > > [  751.424181] tda18271_init:  error -5 on  line 826
> > > [  751.424186] tda18271_tune: error  -5 on line 904
> > >  [  751.424192] tda18271_set_params: error  -5 on line 985
> > > [   752.440172] tda18271_write_regs: ERROR: idx  = 0x5, len = 1, 
>i2c_transfer 
>
> 
> > > returned: -5
> > >                                                                            
>      
>
> >                                                                 
> >
> > >  
> > > 
> >  > Any  ideas?
> > > Thanks
> > > 
> > > 
> >  >      
> > > 
> > 
> 
> 
>

Attachment: messages.zip
Description: Zip archive