On Tue, Oct 20 2009, Alex Chiang wrote:* Jens Axboe <jens.axboe@xxxxxxxxxx>:On Tue, Oct 13 2009, Alex Chiang wrote:Hm, so for some reason, firmware on your machine is telling usIt produces:You mentioned in another mail that you echoed 1 into the variousCan you modprobe acpiphp with debug=1? And send the output?acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
acpiphp_glue: found PCI-to-PCI bridge at PCI 0000:00:05.0
acpiphp_glue: found ACPI PCI Hotplug slot 1 at PCI 0000:08:00
acpiphp: Slot [1] registered
acpiphp_glue: found PCI-to-PCI bridge at PCI 0000:00:07.0
acpiphp_glue: found ACPI PCI Hotplug slot 2 at PCI 0000:0b:00
acpiphp: Slot [2] registered
acpiphp_glue: found PCI-to-PCI bridge at PCI 0000:80:07.0
acpiphp_glue: found ACPI PCI Hotplug slot 6 at PCI 0000:84:00
acpiphp: Slot [6] registered
acpiphp_glue: found PCI-to-PCI bridge at PCI 0000:80:09.0
acpiphp_glue: found ACPI PCI Hotplug slot 7 at PCI 0000:87:00
acpiphp: Slot [7] registered
acpiphp_glue: Bus 0000:87 has 1 slot
acpiphp_glue: Bus 0000:84 has 1 slot
acpiphp_glue: Bus 0000:0b has 1 slot
acpiphp_glue: Bus 0000:08 has 1 slot
acpiphp_glue: Total 4 slots
slots' power files.
Did you do that after modprobing acpiphp with debug=1?
If so, there should be debug output when you try and turn them
on.
acpiphp: enable_slot - physical_slot = 1
acpiphp_glue: acpiphp_enable_slot: Slot status is not ACPI_STA_ALL
acpiphp: enable_slot - physical_slot = 2
acpiphp_glue: acpiphp_enable_slot: Slot status is not ACPI_STA_ALL
acpiphp: enable_slot - physical_slot = 6
acpiphp_glue: acpiphp_enable_slot: Slot status is not ACPI_STA_ALL
acpiphp: enable_slot - physical_slot = 7
acpiphp_glue: acpiphp_enable_slot: Slot status is not ACPI_STA_ALL
that it doesn't think cards are present and/or enabled.
Unfortunately, I don't know why your firmware would be saying
that. We could add some more debug printks to see what firmware
thinks about your system... Or we could just wait and see what
happens after you get your hardware replaced.
New board, the exact same thing happens.
I have a card in one of the slots only this time.No difference in before and after. Odd.
Also, quick dummy check, you are trying to power on populatedYes :-)
slots, right? :)
Can you send the output of lspci -vv? And I like the output ofSend privately.
lspci -vt as well... Both before and after loading acpiphp
please.
If you want to poke us again after your hardware swap, please do
so. Sorry for being not so helpful. :-/
Poke :-)
One more thing I tried was pushing the power button on the slot
manually. With acpiphp, I get the same messages as above. Using pciehp,
I get the same power fault bit interrupt storm. So no difference from
using the sysfs interface or doing it on the box side, doesn't work
either way.