Still broken sata (VIA) on Asus A8V (kernel 2.6.14+) with irqbalance
From: Vladimir B. Savkin
Date: Fri Jul 28 2006 - 08:10:31 EST
Hello!
Here goes my first report on the issue.
On Wed, Feb 01, 2006 at 07:28:00PM +0300, Vladimir B. Savkin wrote:
> My system based on Asus A8V (VIA chipset) works fine with 2.6.13.3,
> but after upgrading (kernels 2.6.14.7 and 2.6.15.1 tried) it
> gaves error messages some minutes after boot.
>
> The messages are as following:
> ata2: command 0xXX timeout, stat 0x50 host_stat 0x4
> where XX gets different values from time to time, 0x25 mostly.
> I/O to this controller halts after that.
>
> Attached are boot dmesg log and lspci output.
>
I just checked - the problem persists with 2.6.17.7
It only shows when irqbalance is running, without irqbalance the box is stable.
Error message is somewhat changed with the new kernel:
ata2: command 0xca timeout, stat 0x50 host_stat 0x4
ata2: status=0x50 { DriveReady SeekComplete }
sda: Current: sense key=0x0
ASC=0x0 ASCQ=0x0
Info fld=0x1f5c9b5
I attach new dmesg log and lspci output.
~
:wq
With best regards,
Vladimir Savkin.
Bootdata ok (command line is root=/dev/sda3 ro idle=poll )
Linux version 2.6.17.7nomsi (vsavkin@forum) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 SMP Thu Jul 27 22:33:46 MSD 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000d7fb0000 (usable)
BIOS-e820: 00000000d7fb0000 - 00000000d7fc0000 (ACPI data)
BIOS-e820: 00000000d7fc0000 - 00000000d7ff0000 (ACPI NVS)
BIOS-e820: 00000000d7ff0000 - 00000000d8000000 (reserved)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000124000000 (usable)
DMI 2.3 present.
ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fa7c0
ACPI: XSDT (v001 A M I OEMXSDT 0x06000530 MSFT 0x00000097) @ 0x00000000d7fb0100
ACPI: FADT (v003 A M I OEMFACP 0x06000530 MSFT 0x00000097) @ 0x00000000d7fb0290
ACPI: MADT (v001 A M I OEMAPIC 0x06000530 MSFT 0x00000097) @ 0x00000000d7fb0390
ACPI: OEMB (v001 A M I OEMBIOS 0x06000530 MSFT 0x00000097) @ 0x00000000d7fc0040
ACPI: DSDT (v001 A0036 A0036001 0x00000001 MSFT 0x0100000d) @ 0x0000000000000000
On node 0 totalpages: 1014154
DMA zone: 2434 pages, LIFO batch:0
DMA32 zone: 866280 pages, LIFO batch:31
Normal zone: 145440 pages, LIFO batch:31
Looks like a VIA chipset. Disabling IOMMU. Override with "iommu=allowed"
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:11 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:11 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at dc000000 (gap: d8000000:27780000)
Built 1 zonelists
Kernel command line: root=/dev/sda3 ro idle=poll
using polling idle threads.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Disabling vsyscall due to use of PM timer
time.c: Using 3.579545 MHz WALL PM GTOD PM timer.
time.c: Detected 2002.649 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0x561b000 - 0x961b000
Memory: 3984080k/4784128k available (2483k kernel code, 143768k reserved, 1711k data, 176k init)
Calibrating delay using timer specific routine.. 4008.30 BogoMIPS (lpj=2004154)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
tbxface-0109 [02] load_tables : ACPI Tables successfully acquired
Parsing all Control Methods:
Table [DSDT](id 0005) - 547 Objects with 51 Devices 147 Methods 25 Regions
ACPI Namespace successfully loaded at root ffffffff8067d360
evxfevnt-0091 [03] enable : Transition to ACPI mode successful
Using local APIC timer interrupts.
result 12516572
Detected 12.516 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4004.55 BogoMIPS (lpj=2002275)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 01
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 568 cycles)
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=275
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
evgpeblk-0941 [06] ev_create_gpe_block : GPE 00 to 0F [_GPE] 2 regs on int 0x9
evgpeblk-1037 [05] ev_initialize_gpe_bloc: Found 7 Wake, Enabled 0 Runtime GPEs in this block
Completing Region/Field/Buffer/Package initialization:............................................................................................................................
Initialized 24/25 Regions 44/44 Fields 41/41 Buffers 15/16 Packages (556 nodes)
Executing all Device _STA and_INI methods:.......................................................
55 Devices found - executed 0 _STA, 0 _INI methods
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Quirk-MSI-K8T Soundcard On
PCI: Unexpected Value in PCI-Register: no Change!
PCI: enabled onboard AC97/MC97 devices
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xdc000000
PCI: Bridge: 0000:00:01.0
IO window: e000-efff
MEM window: fbe00000-fbffffff
PREFETCH window: e0000000-faffffff
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1154088239.810:1): initialized
Total HugeTLB memory allocated, 0
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 16
PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: IC35L080AVVA07-0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: max request size: 128KiB
hdc: 160836480 sectors (82348 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(100)
hdc: cache flushes supported
hdc: hdc1 hdc2 hdc3 hdc4
libata version 1.20 loaded.
sata_via 0000:00:0f.0: version 1.1
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 16
sata_via 0000:00:0f.0: routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xC000 ctl 0xB802 bmdma 0xA800 irq 16
ata2: SATA max UDMA/133 cmd 0xB400 ctl 0xB002 bmdma 0xA808 irq 16
ata1: SATA link down (SStatus 0)
scsi0 : sata_via
ata2: SATA link up 1.5 Gbps (SStatus 113)
ata2: dev 0 cfg 49:2f00 82:74eb 83:7fea 84:4023 85:74e8 86:3c02 87:4023 88:203f
ata2: dev 0 ATA-6, max UDMA/100, 488397168 sectors: LBA48
ata2: dev 0 configured for UDMA/100
scsi1 : sata_via
Vendor: ATA Model: HDS722525VLSA80 Rev: V36O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 >
sd 1:0:0:0: Attached scsi disk sda
sd 1:0:0:0: Attached scsi generic sg0 type 0
usbcore: registered new driver libusual
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@xxxxxxxxxx
Netfilter messages via NETLINK v0.30.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 176k freed
Write protecting the kernel read-only data: 958k
Adding 7912004k swap on /dev/sda2. Priority:2 extents:1 across:7912004k
Adding 3906496k swap on /dev/hdc3. Priority:4 extents:1 across:3906496k
802.1Q VLAN Support v1.8 Ben Greear <greearb@xxxxxxxxxxxxxxx>
All bugs added by David S. Miller <davem@xxxxxxxxxx>
8139too Fast Ethernet driver 0.9.27
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 17 (level, low) -> IRQ 17
eth0: RealTek RTL8139 at 0xffffc20000012000, 00:c0:26:a1:92:f5, IRQ 17
eth0: Identified 8139 chip type 'RTL-8139C'
ReiserFS: sda9: found reiserfs format "3.6" with standard journal
ReiserFS: sda9: using ordered data mode
ReiserFS: sda9: journal params: device sda9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda9: checking transaction log (sda9)
ReiserFS: sda9: replayed 1 transactions in 0 seconds
ReiserFS: sda9: Using r5 hash to sort names
ReiserFS: hdc4: found reiserfs format "3.6" with standard journal
ReiserFS: hdc4: using ordered data mode
ReiserFS: hdc4: journal params: device hdc4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdc4: checking transaction log (hdc4)
ReiserFS: hdc4: replayed 1 transactions in 0 seconds
ReiserFS: hdc4: Using r5 hash to sort names
ReiserFS: sda11: found reiserfs format "3.6" with standard journal
ReiserFS: sda11: using ordered data mode
ReiserFS: sda11: journal params: device sda11, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda11: checking transaction log (sda11)
ReiserFS: sda11: replayed 12 transactions in 0 seconds
ReiserFS: sda11: Using r5 hash to sort names
ReiserFS: sda8: found reiserfs format "3.6" with standard journal
ReiserFS: sda8: using ordered data mode
ReiserFS: sda8: journal params: device sda8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda8: checking transaction log (sda8)
ReiserFS: sda8: replayed 1 transactions in 0 seconds
ReiserFS: sda8: Using r5 hash to sort names
ReiserFS: hdc1: found reiserfs format "3.6" with standard journal
ReiserFS: hdc1: using ordered data mode
ReiserFS: hdc1: journal params: device hdc1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdc1: checking transaction log (hdc1)
ReiserFS: hdc1: replayed 1 transactions in 0 seconds
ReiserFS: hdc1: Using r5 hash to sort names
ReiserFS: sda10: found reiserfs format "3.6" with standard journal
ReiserFS: sda10: using ordered data mode
ReiserFS: sda10: journal params: device sda10, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda10: checking transaction log (sda10)
ReiserFS: sda10: replayed 2 transactions in 0 seconds
ReiserFS: sda10: Using r5 hash to sort names
ReiserFS: sda5: found reiserfs format "3.6" with standard journal
ReiserFS: sda5: using ordered data mode
ReiserFS: sda5: journal params: device sda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda5: checking transaction log (sda5)
ReiserFS: sda5: replayed 1 transactions in 0 seconds
ReiserFS: sda5: Using r5 hash to sort names
ReiserFS: sda6: found reiserfs format "3.6" with standard journal
ReiserFS: sda6: using ordered data mode
ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda6: checking transaction log (sda6)
ReiserFS: sda6: replayed 31 transactions in 0 seconds
ReiserFS: sda6: Using r5 hash to sort names
ReiserFS: hdc2: found reiserfs format "3.6" with standard journal
ReiserFS: hdc2: using ordered data mode
ReiserFS: hdc2: journal params: device hdc2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdc2: checking transaction log (hdc2)
ReiserFS: hdc2: Using r5 hash to sort names
ieee1394: Initialized config rom entry `ip1394'
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[18] MMIO=[fb700000-fb7007ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17
sk98lin: Asus mainboard with buggy VPD? Correcting data.
eth1: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
PrefPort:A RlmtMode:Check Link State
USB Universal Host Controller Interface driver v3.0
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 19
PCI: VIA IRQ fixup for 0000:00:10.0, from 11 to 3
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 19, io base 0x0000c400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 19
PCI: VIA IRQ fixup for 0000:00:10.1, from 11 to 3
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 19, io base 0x0000c800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 19
PCI: VIA IRQ fixup for 0000:00:10.2, from 10 to 3
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 19, io base 0x0000d000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 19
PCI: VIA IRQ fixup for 0000:00:10.3, from 10 to 3
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 19, io base 0x0000d400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800005886c8]
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
acpi_bus-0201 [01] bus_set_power : Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 19
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 19, io mem 0xfbd00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1
vlan0169: add 01:00:5e:00:00:01 mcast address to master interface
vlan0170: add 01:00:5e:00:00:01 mcast address to master interface
NET: Registered protocol family 10
vlan0169: add 33:33:00:00:00:01 mcast address to master interface
vlan0169: add 33:33:ff:a1:92:f5 mcast address to master interface
vlan0170: add 33:33:00:00:00:01 mcast address to master interface
vlan0170: add 33:33:ff:a1:92:f5 mcast address to master interface
IPv6 over IPv4 tunneling driver
0000:00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0282
Subsystem: Asustek Computer, Inc.: Unknown device 80a3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at dc000000 (32-bit, prefetchable) [size=64M]
Capabilities: [80] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] #08 [0060]
Capabilities: [58] #08 [8001]
0000:00:00.1 Host bridge: VIA Technologies, Inc.: Unknown device 1282
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:00.2 Host bridge: VIA Technologies, Inc.: Unknown device 2282
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:00.3 Host bridge: VIA Technologies, Inc.: Unknown device 3282
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:00.4 Host bridge: VIA Technologies, Inc.: Unknown device 4282
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:00.7 Host bridge: VIA Technologies, Inc.: Unknown device 7282
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800 South] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fbe00000-fbffffff
Prefetchable memory behind bridge: e0000000-faffffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 808a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fb700000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at 9400 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0a.0 Ethernet controller: Marvell Technology Group Ltd. Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (rev 13)
Subsystem: Asustek Computer, Inc.: Unknown device 811a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fb900000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at 9800 [size=256]
Expansion ROM at fb800000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
0000:00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at fbb00000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at fba00000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
Subsystem: Asustek Computer, Inc. A7V600 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin B routed to IRQ 16
Region 0: I/O ports at c000 [size=8]
Region 1: I/O ports at b800 [size=4]
Region 2: I/O ports at b400 [size=8]
Region 3: I/O ports at b000 [size=4]
Region 4: I/O ports at a800 [size=16]
Region 5: I/O ports at a400 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc. A7V600 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at fc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. A7V600 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at c400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. A7V600 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. A7V600 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc. A7V600 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc. A7V600 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin C routed to IRQ 19
Region 0: Memory at fbd00000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [K8T800 South]
Subsystem: Asustek Computer, Inc. A7V600 motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
Subsystem: Asustek Computer, Inc.: Unknown device 812a
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at d800 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:11.6 Communication controller: VIA Technologies, Inc. Intel 537 [AC97 Modem] (rev 80)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 0
Region 0: I/O ports at 1000 [disabled] [size=256]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] #08 [2101]
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R200 QM [Radeon 9100] (rev 80) (prog-if 00 [VGA])
Subsystem: PC Partner Limited: Unknown device 7149
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at e000 [size=256]
Region 2: Memory at fbf00000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fbe00000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=48 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-