Some more info. I tried disabling the hdparm command, that didn't
make the 2.4.2-pre4 mount succesfully.
I tried 2.4.2-pre1 and that booted fine.
I'll try pre2 and pre3 versions when I get a chance (thursday night)
and see about turning up the log level, too.
Here is the info on PCI and the drives. I edited out the sound, scsi,
usb, etc.
-Dan
00:00.0 Host bridge: VIA Technologies, Inc. VT82C691 [Apollo PRO] (rev c4)
Flags: bus master, medium devsel, latency 0
Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: d4000000-d7ffffff
Prefetchable memory behind bridge: d8000000-d9ffffff
Capabilities: [80] Power Management version 2
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super] (rev 21)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 10) (prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 32
I/O ports at a000 [size=16]
Capabilities: [c0] Power Management version 2
00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Flags: medium devsel
Capabilities: [68] Power Management version 2
/dev/hda:
Model=Maxtor 51024U2, FwRev=DA620CQ0, SerialNo=K205799C
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=19999728
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
/dev/hdb:
Model=Maxtor 51536U3, FwRev=DA620CQ0, SerialNo=K3H4HFDC
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=29888820
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
--On Tue, Feb 20, 2001 at 07:28:48PM +0100, Vojtech Pavlik wrote: > On Tue, Feb 20, 2001 at 10:16:22AM -0800, Dan Christian wrote: > > > Hello, > > I just tried upgrading to 2.4.2-pre4 from 2.4.1 and get a hang when > > mounting the file systems. I have the same problem with 2.4.1-ac18. > > > > The system is a single processor P3 and uses a VIA chipset (Tyan > > something-or-other). DMA, multi-sector IO, and 32bit sync are enabled > > using hdparm (just before the hang).
-- Dan Christian (650) 604-4507 FAX 604-4036 NASA Ames Research Center, Mail Stop 269-3, Moffett Field, CA 94035 - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Fri Feb 23 2001 - 21:00:25 EST