Hi Linus,
The following patch (versus 2.4.0test6) to the Serial driver fixes the
following bugs. I'd appreciate it if you could apply them to the 2.4
tree. They're all rather straightforward, and all should be fixed
before 2.4 ships.
* Fixed bug which could cause kernel oops if the IRQ on a port
was set to be negative.
* Fixed serial magic-sysrq support (the break key would get
ignored under some circumstances).
* Fixed a bug introduced with the rs_timer conversion which
could cause the timer code to loop because it was possible for
the expire timeout to be set less than jiffies+1.
* Fixed a bug in the PCI generic hueristic code which caused it
fail because it didn't properly count how many I/O Base
Address Regions a particular card had.
* Changed ASYNC_AUTOPROBE to have a bit value so that it
properly shows that it's an externally exported flag.
(Nothing uses ASYNC_AUTOPROBE yet, since it was very recently
introduced, so it's safe to change its value.)
* Fixed a few places where MOD_DEC_USE_COUNT wasn't properly
called, causing the module to be unloadable if certain errors
happened while trying to open a serial port. (Sent in by
Arnaldo Carvalho de Melo <acme@conectiva.com.br>)
* Cleaned up the Timedia support so that it doesn't introduce
quite so much kernel bloat. (Reduces compiled size of serial
driver by 2k!)
* Changed the Config.in dialog so that it makes it clear that
this driver supports the 8250/16550 and compatible UART's.
Some ARM users were getting confused and answering yes when
they say "Standard/Generic serial port".
* Cleaned up the ConnectTech PCI vendor ID's to support a few
more cards and removed some impossible combinations.
Thanks to Arnaldo Melo, Stuart MacDonald, and many others who have
contributed patches and suggestions for this patch set.
- Ted
Patch generated: on Wed Aug 9 23:45:38 EDT 2000 by tytso@snap.thunk.org
against Linux version 2.4.0-test6
===================================================================
RCS file: drivers/char/RCS/Config.in,v
retrieving revision 1.1
diff -u -r1.1 drivers/char/Config.in
--- drivers/char/Config.in 2000/08/10 03:30:32 1.1
+++ drivers/char/Config.in 2000/08/10 03:30:35
@@ -8,7 +8,7 @@
if [ "$CONFIG_VT" = "y" ]; then
bool ' Support for console on virtual terminal' CONFIG_VT_CONSOLE
fi
-tristate 'Standard/generic (dumb) serial support' CONFIG_SERIAL
+tristate 'Standard/generic (8250/16550 and compatible UARTs) serial support' CONFIG_SERIAL
if [ "$CONFIG_SERIAL" = "y" ]; then
bool ' Support for console on serial port' CONFIG_SERIAL_CONSOLE
if [ "$CONFIG_ARCH_ACORN" = "y" ]; then
===================================================================
RCS file: drivers/char/RCS/serial.c,v
retrieving revision 1.1
diff -u -r1.1 drivers/char/serial.c
--- drivers/char/serial.c 2000/08/10 03:30:32 1.1
+++ drivers/char/serial.c 2000/08/10 03:30:35
@@ -51,13 +51,16 @@
*
* 7/00: Support Timedia/Sunix/Exsys PCI cards
*
+ * 7/00: fix some returns on failure not using MOD_DEC_USE_COUNT.
+ * Arnaldo Carvalho de Melo <acme@conectiva.com.br>
+ *
* This module exports the following rs232 io functions:
*
* int rs_init(void);
*/
-static char *serial_version = "5.01";
-static char *serial_revdate = "2000-05-29";
+static char *serial_version = "5.02";
+static char *serial_revdate = "2000-08-09";
/*
* Serial driver configuration section. Here are the various options:
@@ -142,6 +145,10 @@
#endif
#endif
+#ifdef MODULE
+#undef CONFIG_SERIAL_CONSOLE
+#endif
+
#define CONFIG_SERIAL_RSA
#define RS_STROBE_TIME (10*HZ)
@@ -260,8 +267,9 @@
static int IRQ_timeout[NR_IRQS];
#ifdef CONFIG_SERIAL_CONSOLE
static struct console sercons;
+static int lsr_break_flag = 0;
#endif
-#if defined(CONFIG_SERIAL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) && !defined(MODULE)
+#if defined(CONFIG_SERIAL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
static unsigned long break_pressed; /* break, really ... */
#endif
@@ -281,7 +289,7 @@
{ "16550", 1, 0 },
{ "16550A", 16, UART_CLEAR_FIFO | UART_USE_FIFO },
{ "cirrus", 1, 0 }, /* usurped by cyclades.c */
- { "ST16650", 1, UART_CLEAR_FIFO |UART_STARTECH },
+ { "ST16650", 1, UART_CLEAR_FIFO | UART_STARTECH },
{ "ST16650V2", 32, UART_CLEAR_FIFO | UART_USE_FIFO |
UART_STARTECH },
{ "TI16750", 64, UART_CLEAR_FIFO | UART_USE_FIFO},
@@ -295,14 +303,18 @@
{ 0, 0}
};
-#if defined(CONFIG_SERIAL_RSA) && defined(MODULE)
+#ifdef CONFIG_SERIAL_RSA
#define PORT_RSA_MAX 4
static int probe_rsa[PORT_RSA_MAX];
static int force_rsa[PORT_RSA_MAX];
+#ifdef MODULE
MODULE_PARM(probe_rsa, "1-" __MODULE_STRING(PORT_RSA_MAX) "i");
+MODULE_PARM_DESC(probe_rsa, "Probe I/O ports for RSA");
MODULE_PARM(force_rsa, "1-" __MODULE_STRING(PORT_RSA_MAX) "i");
+MODULE_PARM_DESC(force_rsa, "Force I/O ports for RSA");
+#endif
#endif /* CONFIG_SERIAL_RSA */
static struct serial_state rs_table[RS_TABLE_SIZE] = {
@@ -313,7 +325,7 @@
#if (defined(ENABLE_SERIAL_PCI) || defined(ENABLE_SERIAL_PNP))
#define NR_PCI_BOARDS 8
-/* We don't unregister PCI boards right now */
+
static struct pci_board_inst serial_pci_board[NR_PCI_BOARDS];
static int serial_pci_board_idx = 0;
@@ -573,6 +585,23 @@
if (*status & UART_LSR_BI) {
*status &= ~(UART_LSR_FE | UART_LSR_PE);
icount->brk++;
+ /*
+ * We do the SysRQ and SAK checking
+ * here because otherwise the break
+ * may get masked by ignore_status_mask
+ * or read_status_mask.
+ */
+#if defined(CONFIG_SERIAL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+ if (info->line == sercons.index) {
+ if (!break_pressed) {
+ break_pressed = jiffies;
+ goto ignore_char;
+ }
+ break_pressed = 0;
+ }
+#endif
+ if (info->flags & ASYNC_SAK)
+ do_SAK(tty);
} else if (*status & UART_LSR_PE)
icount->parity++;
else if (*status & UART_LSR_FE)
@@ -591,23 +620,19 @@
goto ignore_char;
}
*status &= info->read_status_mask;
-
+
+#ifdef CONFIG_SERIAL_CONSOLE
+ if (info->line == sercons.index) {
+ /* Recover the break flag from console xmit */
+ *status |= lsr_break_flag;
+ lsr_break_flag = 0;
+ }
+#endif
if (*status & (UART_LSR_BI)) {
#ifdef SERIAL_DEBUG_INTR
printk("handling break....");
#endif
-#if defined(CONFIG_SERIAL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) && !defined(MODULE)
- if (info->line == sercons.index) {
- if (!break_pressed) {
- break_pressed = jiffies;
- goto ignore_char;
- }
- break_pressed = 0;
- }
-#endif
*tty->flip.flag_buf_ptr = TTY_BREAK;
- if (info->flags & ASYNC_SAK)
- do_SAK(tty);
} else if (*status & UART_LSR_PE)
*tty->flip.flag_buf_ptr = TTY_PARITY;
else if (*status & UART_LSR_FE)
@@ -626,7 +651,7 @@
goto ignore_char;
}
}
-#if defined(CONFIG_SERIAL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) && !defined(MODULE)
+#if defined(CONFIG_SERIAL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
if (break_pressed && info->line == sercons.index) {
if (ch != 0 &&
time_before(jiffies, break_pressed + HZ*5)) {
@@ -1076,7 +1101,7 @@
#endif
restore_flags(flags);
- mod_timer(&serial_timer, jiffies + IRQ_timeout[0] - 2);
+ mod_timer(&serial_timer, jiffies + IRQ_timeout[0]);
}
}
@@ -1111,7 +1136,7 @@
}
if (!irq)
timeout = timeout / 2;
- IRQ_timeout[irq] = timeout ? timeout : 1;
+ IRQ_timeout[irq] = (timeout > 3) ? timeout-2 : 1;
}
#ifdef CONFIG_SERIAL_RSA
@@ -2077,7 +2102,7 @@
new_serial.irq = irq_cannonicalize(new_serial.irq);
- if ((new_serial.irq >= NR_IRQS) ||
+ if ((new_serial.irq >= NR_IRQS) || (new_serial.irq < 0) ||
(new_serial.baud_base < 9600)|| (new_serial.type < PORT_UNKNOWN) ||
(new_serial.type > PORT_MAX) || (new_serial.type == PORT_CIRRUS) ||
(new_serial.type == PORT_STARTECH)) {
@@ -2310,7 +2335,7 @@
static int do_autoconfig(struct async_struct * info)
{
- int retval;
+ int irq, retval;
if (!capable(CAP_SYS_ADMIN))
return -EPERM;
@@ -2323,8 +2348,11 @@
autoconfig(info->state);
if ((info->state->flags & ASYNC_AUTO_IRQ) &&
(info->state->port != 0) &&
- (info->state->type != PORT_UNKNOWN))
- info->state->irq = detect_uart_irq(info->state);
+ (info->state->type != PORT_UNKNOWN)) {
+ irq = detect_uart_irq(info->state);
+ if (irq > 0)
+ info->state->irq = irq;
+ }
retval = startup(info);
if (retval)
@@ -3111,8 +3139,10 @@
}
tty->driver_data = info;
info->tty = tty;
- if (serial_paranoia_check(info, tty->device, "rs_open"))
+ if (serial_paranoia_check(info, tty->device, "rs_open")) {
+ MOD_DEC_USE_COUNT;
return -ENODEV;
+ }
#ifdef SERIAL_DEBUG_OPEN
printk("rs_open %s%d, count = %d\n", tty->driver.name, info->line,
@@ -3125,6 +3155,7 @@
if (!tmp_buf) {
page = get_zeroed_page(GFP_KERNEL);
if (!page) {
+ MOD_DEC_USE_COUNT;
return -ENOMEM;
}
if (tmp_buf)
@@ -3140,6 +3171,7 @@
(info->flags & ASYNC_CLOSING)) {
if (info->flags & ASYNC_CLOSING)
interruptible_sleep_on(&info->close_wait);
+ MOD_DEC_USE_COUNT;
#ifdef SERIAL_DO_RESTART
return ((info->flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS);
@@ -3153,6 +3185,7 @@
*/
retval = startup(info);
if (retval) {
+ MOD_DEC_USE_COUNT;
return retval;
}
@@ -3162,6 +3195,7 @@
printk("rs_open returning after block_til_ready with %d\n",
retval);
#endif
+ MOD_DEC_USE_COUNT;
return retval;
}
@@ -3486,6 +3520,7 @@
* (Exoray@isys.ca) claims that it's needed for 952
* dual UART's (which are not recommended for new designs).
*/
+ info->ACR = 0;
serial_out(info, UART_LCR, 0xBF);
serial_out(info, UART_EFR, 0x10);
serial_out(info, UART_LCR, 0x00);
@@ -3804,10 +3839,11 @@
if (idx >= max_port)
return 1;
}
-
+
offset = board->first_uart_offset;
/* Timedia/SUNIX uses a mixture of BARs and offsets */
+ /* Ugh, this is ugly as all hell --- TYT */
if(dev->vendor == PCI_VENDOR_ID_TIMEDIA ) /* 0x1409 */
switch(idx) {
case 0: base_idx=0;
@@ -4090,6 +4126,62 @@
return(0);
}
+/*
+ * Timedia has an explosion of boards, and to avoid the PCI table from
+ * growing *huge*, we use this function to collapse some 70 entries
+ * in the PCI table into one, for sanity's and compactness's sake.
+ */
+static unsigned short timedia_single_port[] = {
+ 0x4025, 0x4027, 0x4028, 0x5025, 0x5027, 0 };
+static unsigned short timedia_dual_port[] = {
+ 0x0002, 0x4036, 0x4037, 0x4038, 0x4078, 0x4079, 0x4085,
+ 0x4088, 0x4089, 0x5037, 0x5078, 0x5079, 0x5085, 0x6079,
+ 0x7079, 0x8079, 0x8137, 0x8138, 0x8237, 0x8238, 0x9079,
+ 0x9137, 0x9138, 0x9237, 0x9238, 0xA079, 0xB079, 0xC079,
+ 0xD079, 0 };
+static unsigned short timedia_quad_port[] = {
+ 0x4055, 0x4056, 0x4095, 0x4096, 0x5056, 0x8156, 0x8157,
+ 0x8256, 0x8257, 0x9056, 0x9156, 0x9157, 0x9158, 0x9159,
+ 0x9256, 0x9257, 0xA056, 0xA157, 0xA158, 0xA159, 0xB056,
+ 0xB157, 0 };
+static unsigned short timedia_eight_port[] = {
+ 0x4065, 0x4066, 0x5065, 0x5066, 0x8166, 0x9066, 0x9166,
+ 0x9167, 0x9168, 0xA066, 0xA167, 0xA168, 0 };
+static struct timedia_struct {
+ int num;
+ unsigned short *ids;
+} timedia_data[] = {
+ { 1, timedia_single_port },
+ { 2, timedia_dual_port },
+ { 4, timedia_quad_port },
+ { 8, timedia_eight_port },
+ { 0, 0 }
+};
+
+static int
+#ifndef MODULE
+__init
+#endif
+pci_timedia_fn(struct pci_dev *dev, struct pci_board *board, int enable)
+{
+ int i, j;
+ unsigned short *ids;
+
+ if (!enable)
+ return 0;
+
+ for (i=0; timedia_data[i].num; i++) {
+ ids = timedia_data[i].ids;
+ for (j=0; ids[j]; j++) {
+ if (pci_get_subvendor(dev) == ids[j]) {
+ board->num_ports = timedia_data[i].num;
+ return 0;
+ }
+ }
+ }
+ return 0;
+}
+
/*
* This is the configuration table for all of the PCI serial boards
@@ -4116,58 +4208,50 @@
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_232,
SPCI_FL_BASE1, 2, 1382400 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960V2,
+ { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_232,
SPCI_FL_BASE1, 8, 1382400 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960V2,
+ { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_232,
SPCI_FL_BASE1, 4, 1382400 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960V2,
+ { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_232,
SPCI_FL_BASE1, 2, 1382400 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
+ { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485,
SPCI_FL_BASE1, 8, 921600 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
+ { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485_4_4,
SPCI_FL_BASE1, 8, 921600 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
+ { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485,
SPCI_FL_BASE1, 4, 921600 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
+ { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485_2_2,
SPCI_FL_BASE1, 4, 921600 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960,
+ { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_485,
SPCI_FL_BASE1, 2, 921600 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960V2,
+ { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485_2_6,
SPCI_FL_BASE1, 8, 921600 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960V2,
+ { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485_4_4,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH081101V1,
SPCI_FL_BASE1, 8, 921600 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960V2,
+ { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V351,
PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_BH041101V1,
SPCI_FL_BASE1, 4, 921600 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960V2,
- PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485_2_2,
- SPCI_FL_BASE1, 4, 921600 },
- { PCI_VENDOR_ID_V3, PCI_DEVICE_ID_V3_V960V2,
- PCI_SUBVENDOR_ID_CONNECT_TECH,
- PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_485,
- SPCI_FL_BASE1, 2, 921600 },
{ PCI_VENDOR_ID_SEALEVEL, PCI_DEVICE_ID_SEALEVEL_U530,
PCI_ANY_ID, PCI_ANY_ID,
SPCI_FL_BASE2 | SPCI_FL_BASE_TABLE, 1, 115200 },
@@ -4196,6 +4280,9 @@
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_SPCOM800,
PCI_ANY_ID, PCI_ANY_ID,
SPCI_FL_BASE2, 8, 921600 },
+ { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_1077,
+ PCI_ANY_ID, PCI_ANY_ID,
+ SPCI_FL_BASE2, 4, 921600 },
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
PCI_SUBVENDOR_ID_KEYSPAN,
PCI_SUBDEVICE_ID_KEYSPAN_SX2,
@@ -4265,75 +4352,10 @@
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI95N,
PCI_ANY_ID, PCI_ANY_ID,
SPCI_FL_BASE0 | SPCI_FL_REGION_SZ_CAP, 32, 115200 },
- /* PCI_VENDOR_ID_TIMEDIA/Sunix, PCI_DEVICE_ID_TIMEDIA_1889, */
- { 0x1409, 0x7168, 0x1409, 0x0002, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4036A*/
- { 0x1409, 0x7168, 0x1409, 0x4025, SPCI_FL_BASE_TABLE, 1, 921600 }, /*4025A*/
- { 0x1409, 0x7168, 0x1409, 0x4027, SPCI_FL_BASE_TABLE, 1, 921600 }, /*4027A*/
- { 0x1409, 0x7168, 0x1409, 0x4028, SPCI_FL_BASE_TABLE, 1, 921600 }, /*4028D*/
- { 0x1409, 0x7168, 0x1409, 0x4036, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4036D*/
- { 0x1409, 0x7168, 0x1409, 0x4037, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4037A*/
- { 0x1409, 0x7168, 0x1409, 0x4038, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4038D*/
- { 0x1409, 0x7168, 0x1409, 0x4055, SPCI_FL_BASE_TABLE, 4, 921600 }, /*4055A*/
- { 0x1409, 0x7168, 0x1409, 0x4056, SPCI_FL_BASE_TABLE, 4, 921600 }, /*4056A*/
- { 0x1409, 0x7168, 0x1409, 0x4065, SPCI_FL_BASE_TABLE, 8, 921600 }, /*4065A*/
- { 0x1409, 0x7168, 0x1409, 0x4066, SPCI_FL_BASE_TABLE, 8, 921600 }, /*4066A*/
- { 0x1409, 0x7168, 0x1409, 0x4078, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4078A*/
- { 0x1409, 0x7168, 0x1409, 0x4079, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4079H*/
- { 0x1409, 0x7168, 0x1409, 0x4085, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4085H*/
- { 0x1409, 0x7168, 0x1409, 0x4088, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4088A*/
- { 0x1409, 0x7168, 0x1409, 0x4089, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4089A*/
- { 0x1409, 0x7168, 0x1409, 0x4095, SPCI_FL_BASE_TABLE, 4, 921600 }, /*4095A*/
- { 0x1409, 0x7168, 0x1409, 0x4096, SPCI_FL_BASE_TABLE, 4, 921600 }, /*4096A*/
- { 0x1409, 0x7168, 0x1409, 0x5025, SPCI_FL_BASE_TABLE, 1, 921600 }, /*4025D*/
- { 0x1409, 0x7168, 0x1409, 0x5027, SPCI_FL_BASE_TABLE, 1, 921600 }, /*4027D*/
- { 0x1409, 0x7168, 0x1409, 0x5037, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4037D*/
- { 0x1409, 0x7168, 0x1409, 0x5056, SPCI_FL_BASE_TABLE, 4, 921600 }, /*4056R*/
- { 0x1409, 0x7168, 0x1409, 0x5065, SPCI_FL_BASE_TABLE, 8, 921600 }, /*4065R*/
- { 0x1409, 0x7168, 0x1409, 0x5066, SPCI_FL_BASE_TABLE, 8, 921600 }, /*4066R*/
- { 0x1409, 0x7168, 0x1409, 0x5078, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4078U*/
- { 0x1409, 0x7168, 0x1409, 0x5079, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4079A*/
- { 0x1409, 0x7168, 0x1409, 0x5085, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4085U*/
- { 0x1409, 0x7168, 0x1409, 0x6079, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4079R*/
- { 0x1409, 0x7168, 0x1409, 0x7079, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4079S*/
- { 0x1409, 0x7168, 0x1409, 0x8079, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4079D*/
- { 0x1409, 0x7168, 0x1409, 0x8137, SPCI_FL_BASE_TABLE, 2, 921600 }, /*8137*/
- { 0x1409, 0x7168, 0x1409, 0x8138, SPCI_FL_BASE_TABLE, 2, 921600 }, /*8138*/
- { 0x1409, 0x7168, 0x1409, 0x8156, SPCI_FL_BASE_TABLE, 4, 921600 }, /*8156*/
- { 0x1409, 0x7168, 0x1409, 0x8157, SPCI_FL_BASE_TABLE, 4, 921600 }, /*8157*/
- { 0x1409, 0x7168, 0x1409, 0x8166, SPCI_FL_BASE_TABLE, 8, 921600 }, /*8166*/
- { 0x1409, 0x7168, 0x1409, 0x8237, SPCI_FL_BASE_TABLE, 2, 921600 }, /*8237*/
- { 0x1409, 0x7168, 0x1409, 0x8238, SPCI_FL_BASE_TABLE, 2, 921600 }, /*8238*/
- { 0x1409, 0x7168, 0x1409, 0x8256, SPCI_FL_BASE_TABLE, 4, 921600 }, /*8256*/
- { 0x1409, 0x7168, 0x1409, 0x8257, SPCI_FL_BASE_TABLE, 4, 921600 }, /*8257*/
- { 0x1409, 0x7168, 0x1409, 0x9056, SPCI_FL_BASE_TABLE, 4, 921600 }, /*9056A*/
- { 0x1409, 0x7168, 0x1409, 0x9066, SPCI_FL_BASE_TABLE, 8, 921600 }, /*9066A*/
- { 0x1409, 0x7168, 0x1409, 0x9079, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4079E*/
- { 0x1409, 0x7168, 0x1409, 0x9137, SPCI_FL_BASE_TABLE, 2, 921600 }, /*8137S*/
- { 0x1409, 0x7168, 0x1409, 0x9138, SPCI_FL_BASE_TABLE, 2, 921600 }, /*8138S*/
- { 0x1409, 0x7168, 0x1409, 0x9156, SPCI_FL_BASE_TABLE, 4, 921600 }, /*8156S*/
- { 0x1409, 0x7168, 0x1409, 0x9157, SPCI_FL_BASE_TABLE, 4, 921600 }, /*8157S*/
- { 0x1409, 0x7168, 0x1409, 0x9158, SPCI_FL_BASE_TABLE, 4, 921600 }, /*9158*/
- { 0x1409, 0x7168, 0x1409, 0x9159, SPCI_FL_BASE_TABLE, 4, 921600 }, /*9159*/
- { 0x1409, 0x7168, 0x1409, 0x9166, SPCI_FL_BASE_TABLE, 8, 921600 }, /*8166S*/
- { 0x1409, 0x7168, 0x1409, 0x9167, SPCI_FL_BASE_TABLE, 8, 921600 }, /*9167*/
- { 0x1409, 0x7168, 0x1409, 0x9168, SPCI_FL_BASE_TABLE, 8, 921600 }, /*9168*/
- { 0x1409, 0x7168, 0x1409, 0x9237, SPCI_FL_BASE_TABLE, 2, 921600 }, /*8237S*/
- { 0x1409, 0x7168, 0x1409, 0x9238, SPCI_FL_BASE_TABLE, 2, 921600 }, /*8238S*/
- { 0x1409, 0x7168, 0x1409, 0x9256, SPCI_FL_BASE_TABLE, 4, 921600 }, /*8256S*/
- { 0x1409, 0x7168, 0x1409, 0x9257, SPCI_FL_BASE_TABLE, 4, 921600 }, /*8257S*/
- { 0x1409, 0x7168, 0x1409, 0xA056, SPCI_FL_BASE_TABLE, 4, 921600 }, /*9056B*/
- { 0x1409, 0x7168, 0x1409, 0xA066, SPCI_FL_BASE_TABLE, 8, 921600 }, /*9066B*/
- { 0x1409, 0x7168, 0x1409, 0xA079, SPCI_FL_BASE_TABLE, 2, 921600 }, /*4079F*/
- { 0x1409, 0x7168, 0x1409, 0xA157, SPCI_FL_BASE_TABLE, 4, 921600 }, /*9157*/
- { 0x1409, 0x7168, 0x1409, 0xA158, SPCI_FL_BASE_TABLE, 4, 921600 }, /*9158S*/
- { 0x1409, 0x7168, 0x1409, 0xA159, SPCI_FL_BASE_TABLE, 4, 921600 }, /*9159S*/
- { 0x1409, 0x7168, 0x1409, 0xA167, SPCI_FL_BASE_TABLE, 8, 921600 }, /*9167S*/
- { 0x1409, 0x7168, 0x1409, 0xA168, SPCI_FL_BASE_TABLE, 8, 921600 }, /*9168S*/
- { 0x1409, 0x7168, 0x1409, 0xB056, SPCI_FL_BASE_TABLE, 4, 921600 }, /*9056C*/
- { 0x1409, 0x7168, 0x1409, 0xB079, SPCI_FL_BASE_TABLE, 2, 921600 }, /*9079A*/
- { 0x1409, 0x7168, 0x1409, 0xB157, SPCI_FL_BASE_TABLE, 4, 921600 }, /*9157S*/
- { 0x1409, 0x7168, 0x1409, 0xC079, SPCI_FL_BASE_TABLE, 2, 921600 }, /*9079B*/
- { 0x1409, 0x7168, 0x1409, 0xD079, SPCI_FL_BASE_TABLE, 2, 921600 }, /*9079C*/
+ { PCI_VENDOR_ID_TIMEDIA, PCI_DEVICE_ID_TIMEDIA_1889,
+ PCI_VENDOR_ID_TIMEDIA, PCI_ANY_ID,
+ SPCI_FL_BASE_TABLE, 1, 921600,
+ 0, 0, pci_timedia_fn },
{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DSERIAL,
PCI_ANY_ID, PCI_ANY_ID,
SPCI_FL_BASE0 | SPCI_FL_BASE_TABLE, 2, 115200 },
@@ -4540,7 +4562,7 @@
{ PCI_VENDOR_ID_ROCKWELL, 0x1004,
0x1048, 0x1500,
SPCI_FL_BASE1, 1, 115200 },
-#ifdef CONFIG_DDB5074
+#if CONFIG_DDB5074
/*
* NEC Vrc-5074 (Nile 4) builtin UART.
* Conditionally compiled in since this is a motherboard device.
@@ -4580,7 +4602,7 @@
for (i=0; i < 6; i++) {
if (IS_PCI_REGION_IOPORT(dev, i)) {
- num_port = 0;
+ num_port++;
if (first_port == -1)
first_port = i;
} else {
@@ -5077,16 +5099,6 @@
int i;
struct serial_state * state;
- if (serial_timer.function) {
- printk("RS_TIMER already set, another serial driver "
- "already loaded?\n");
-#ifdef MODULE
- printk("Can't load serial driver module over built-in "
- "serial driver\n");
-#endif
- return -EBUSY;
- }
-
init_bh(SERIAL_BH, do_serial_bh);
init_timer(&serial_timer);
serial_timer.function = rs_timer;
@@ -5419,6 +5431,8 @@
module_init(rs_init);
module_exit(rs_fini);
+MODULE_DESCRIPTION("Standard/generic (dumb) serial driver");
+MODULE_AUTHOR("Theodore Ts'o <tytso@mit.edu>");
/*
@@ -5437,10 +5451,17 @@
*/
static inline void wait_for_xmitr(struct async_struct *info)
{
- unsigned int tmout = 1000000;
+ unsigned int status, tmout = 1000000;
+
+ do {
+ status = serial_in(info, UART_LSR);
- while (--tmout &&
- ((serial_in(info, UART_LSR) & BOTH_EMPTY) != BOTH_EMPTY));
+ if (status & UART_LSR_BI)
+ lsr_break_flag = UART_LSR_BI;
+
+ if (--tmout == 0)
+ break;
+ } while((status & BOTH_EMPTY) != BOTH_EMPTY);
}
===================================================================
RCS file: include/linux/RCS/serial.h,v
retrieving revision 1.1
diff -u -r1.1 include/linux/serial.h
--- include/linux/serial.h 2000/08/10 03:30:32 1.1
+++ include/linux/serial.h 2000/08/10 03:33:27
@@ -123,6 +123,8 @@
#define ASYNC_BUGGY_UART 0x4000 /* This is a buggy UART, skip some safety
* checks. Note: can be dangerous! */
+#define ASYNC_AUTOPROBE 0x8000 /* Port was autoprobed by PCI or PNP code */
+
#define ASYNC_FLAGS 0x7FFF /* Possible legal async flags */
#define ASYNC_USR_MASK 0x3430 /* Legal flags that non-privileged
* users can set or reset */
@@ -137,7 +139,6 @@
#define ASYNC_CHECK_CD 0x02000000 /* i.e., CLOCAL */
#define ASYNC_SHARE_IRQ 0x01000000 /* for multifunction cards
--- no longer used */
-#define ASYNC_AUTOPROBE 0x00800000 /* Port was autoprobed */
#define ASYNC_INTERNAL_FLAGS 0xFF000000 /* Internal flags */
===================================================================
RCS file: include/linux/RCS/pci_ids.h,v
retrieving revision 1.1
diff -u -r1.1 include/linux/pci_ids.h
--- include/linux/pci_ids.h 2000/08/10 03:30:32 1.1
+++ include/linux/pci_ids.h 2000/08/10 03:30:35
@@ -549,6 +549,7 @@
#define PCI_VENDOR_ID_PLX 0x10b5
#define PCI_VENDOR_ID_PLX_ROMULUS 0x106a
#define PCI_DEVICE_ID_PLX_SPCOM800 0x1076
+#define PCI_DEVICE_ID_PLX_1077 0x1077
#define PCI_DEVICE_ID_PLX_SPCOM200 0x1103
#define PCI_DEVICE_ID_PLX_9050 0x9050
#define PCI_DEVICE_ID_PLX_9060 0x9060
@@ -856,8 +857,8 @@
#define PCI_VENDOR_ID_V3 0x11b0
#define PCI_DEVICE_ID_V3_V960 0x0001
#define PCI_DEVICE_ID_V3_V350 0x0001
-#define PCI_DEVICE_ID_V3_V960V2 0x0002
-#define PCI_DEVICE_ID_V3_V350V2 0x0002
+#define PCI_DEVICE_ID_V3_V961 0x0002
+#define PCI_DEVICE_ID_V3_V351 0x0002
#define PCI_VENDOR_ID_NP 0x11bc
#define PCI_DEVICE_ID_NP_PCI_FDDI 0x0001
@@ -978,6 +979,9 @@
#define PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485 0x0006
#define PCI_SUBDEVICE_ID_CONNECT_TECH_BH4_485_2_2 0x0007
#define PCI_SUBDEVICE_ID_CONNECT_TECH_BH2_485 0x0008
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_BH8_485_2_6 0x0009
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_BH081101V1 0x000A
+#define PCI_SUBDEVICE_ID_CONNECT_TECH_BH041101V1 0x000B
#define PCI_VENDOR_ID_PICTUREL 0x12c5
#define PCI_DEVICE_ID_PICTUREL_PCIVST 0x0081
===================================================================
RCS file: RCS/MAINTAINERS,v
retrieving revision 1.1
diff -u -r1.1 MAINTAINERS
--- MAINTAINERS 2000/08/10 03:30:32 1.1
+++ MAINTAINERS 2000/08/10 03:30:35
@@ -87,6 +87,13 @@
L: linux-hams@vger.rutgers.edu
S: Maintained
+8250/16?50 (AND CLONE UARTS) SERIAL DRIVER
+P: Theodore Ts'o
+M: tytso@mit.edu
+L: linux-serial@vger.rutgers.edu
+W: http://serial.sourceforge.net
+S: Maintained
+
8390 NETWORK DRIVERS [WD80x3/SMC-ELITE, SMC-ULTRA, NE2000, 3C503, etc.]
P: Paul Gortmaker
M: p_gortmaker@yahoo.com
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Tue Aug 15 2000 - 21:00:20 EST