I have booted 2.3.16 with vga=normal and found the problem (2.3.13 and 2.3.15 also
don't boot normal, but I didn't see anything, as I used vga=794 and nothing print).
At boot:
Partition check:
sda: sda1 sda2 < sda5 >
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 >
Found PIIX4 ACPI device at e400
scsi: aborting command due to timeout : pid 36, scsi 0, channel 0, id 4, lun 0 0
x28 00 00 70 84 4c 00 00 02 00
SCSI host 0 abort (pid 36) timeout - reseting
SCSI bus is being reset for host 0 channel 0.
SCSI ... reseted...
SCSI ...
ad nauseam...
The drive four is ultra2wide..., from 2.2.12:
(scsi0) <Adaptec AIC-7890/1 Ultra2 SCSI host adapter> found at PCI 6/0
(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 374 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.19/3.2.4
<Adaptec AIC-7890/1 Ultra2 SCSI host adapter>
scsi : 1 host.
(scsi0:0:0:0) Synchronous at 20.0 Mbyte/sec, offset 15.
Vendor: QUANTUM Model: FIREBALL_TM3200S Rev: 300X
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:1:0) Synchronous at 20.0 Mbyte/sec, offset 8.
Vendor: PIONEER Model: DVD-ROM DVD-303 Rev: 1.09
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
(scsi0:0:2:0) Synchronous at 16.0 Mbyte/sec, offset 16.
Vendor: PIONEER Model: CD-ROM DR-U06S Rev: 1.05
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr1 at scsi0, channel 0, id 2, lun 0
(scsi0:0:3:0) Synchronous at 10.0 Mbyte/sec, offset 8.
Vendor: PLEXTOR Model: CD-R PX-R820T Rev: 1.05
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr2 at scsi0, channel 0, id 3, lun 0
(scsi0:0:4:0) Synchronous at 80.0 Mbyte/sec, offset 15.
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 4, lun 0
scsi : detected 3 SCSI cdroms 2 SCSI disks total.
sr0: scsi3-mmc drive: 0x/0x cd/rw xa/form2 cdda tray
Uniform CDROM driver Revision: 2.55
sr1: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
sr2: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray
SCSI device sda: hdwr sector= 512 bytes. Sectors= 6281856 [3067 MB] [3.1 GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17850000 [8715 MB] [8.7 GB]
PCI latency timer (CFLT) is unreasonably low at 0. Setting to 32 clocks.
eth0: Intel EtherExpress Pro 10/100 at 0xa800, 00:E0:18:90:14:C5, IRQ 14.
Board assembly 668081-002, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x24c9f043).
Receiver lock-up workaround activated.
Partition check:
sda: sda1 sda2 < sda5 >
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 >
VFS: Mounted root (ext2 filesystem) readonly.
And my system is RedHat 6.0.
Thanks,
Please, don't cc to me: I am on the list...
Greg ICQ:16624071
''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''
Gregoire Favre, Institut de Mathématique de l'Universite de Lausanne
+41216923573,+41763231357, http://www.unil.ch/ima/docs/Personnes/gfavre
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/