I have an ASUS-Board P2L97-S with an Adaptec AIC-7880 Ultra SCSI host
adapter and no problems so far.
There are some differences between my and your setup:
Paul Fulghum <paulkf@austin.rr.com> writes:
> Here are the logs from this incident:
>
> Jun 18 22:45:02 p6 kernel: Linux version 2.2.10 (root@p6.pipehead.org)
> (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 SMP
# gcc -v
Reading specs from /usr/lib/gcc-lib/i486-linux/2.7.2.3/specs
gcc version 2.7.2.3
> Jun 18 22:45:02 p6 kernel: Processor #0 Pentium(tm) Pro APIC version 17
> Jun 18 22:45:02 p6 kernel: Processor #1 Pentium(tm) Pro APIC version 17
Mine is a single processor board (Pentium II 266 MHz).
> Jun 18 22:45:02 p6 rc: Starting pcmcia succeeded
I don't use pcmcia.
> Jun 18 22:45:02 p6 kernel: pty: 256 Unix98 ptys configured
I don't use Unix98 ptys.
> Jun 18 22:45:02 p6 kernel: PIIX4: IDE controller on PCI bus 00 dev 39
I have no IDE disks.
> Jun 18 17:44:55 p6 fsck: /dev/sdb7: clean, 64598/1024000 files,
I have only _one_ SCSI disk, a Plextor SCSI CDROM, and a HP SCSI Tape.
> Jun 18 22:45:02 p6 kernel: (scsi0) <Adaptec AIC-7895 Ultra SCSI host
> adapter> found at PCI 14/0
> Jun 18 22:45:02 p6 kernel: (scsi0) Wide Channel A, SCSI ID=7, 32/255
> SCBs
> Jun 18 22:45:02 p6 kernel: (scsi0) Warning - detected auto-termination
> Jun 18 22:45:02 p6 kernel: (scsi0) Please verify driver detected
> settings are correct.
> Jun 18 22:45:02 p6 kernel: (scsi0) If not, then please properly set the
> device termination
> Jun 18 22:45:02 p6 kernel: (scsi0) in the Adaptec SCSI BIOS by hitting
> CTRL-A when prompted
> Jun 18 22:45:02 p6 kernel: (scsi0) during machine bootup.
> Jun 18 22:45:02 p6 kernel: (scsi0) Cables present (Int-50 NO, Int-68 NO,
> Ext-68 NO)
I don't see these messages. What does the last line mean? No cables present?
> Jun 18 22:45:02 p6 kernel: scsi : 2 hosts.
I have only _one_ adapter.
> Jun 18 22:45:02 p6 kernel: NTFS version 990411
I don't use NTFS.
> Jun 18 22:45:04 p6 nfs: Starting NFS services: succeeded
I neither use nor provide NFS services.
> Jun 18 22:45:02 p6 kernel: 3c59x.c:v0.99H 11/17/98 Donald Becker
> http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
> Jun 18 22:45:02 p6 kernel: eth0: 3Com 3c900 Boomerang 10baseT at
> 0xef00, 00:10:4b:d5:71:f9, IRQ 11
I don't have ethernet.
> Jun 18 22:45:09 p6 xfs: xfs startup succeeded
> Jun 18 22:45:10 p6 smb: smbd startup succeeded
> Jun 18 22:45:10 p6 smb: nmbd startup succeeded
I don't use xfs, smb.
Regards, Olaf.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/