Hi
I am having problems with an UM8886bf ide chipset. It is very slow. I have
included the output from dmesg below. Is there anything I can do to make
it faster? hdparm -d 1 doesn't work.
Regards
--
Rob Murray
--e5bfZ/T2xnjpUIbw
Content-Type: message/rfc822
Received: from localhost [127.0.0.1] (robbie)
by linux.scot-mur.demon.co.uk with esmtp (Exim 2.11 #1 (Debian))
id 10sn7E-0003hs-00; Sat, 12 Jun 1999 13:42:28 +0100
Received: from mailserver.scot-mur.demon.co.uk
by localhost with POP3 (fetchmail-5.0.1)
for robbie@localhost (single-drop); Sat, 12 Jun 1999 13:42:28 +0100 (BST)
Received: from root by mailserver.scot-mur.demon.co.uk with local (Exim 2.11 #1 (Debian))
id 10snsc-00003K-00; Sat, 12 Jun 1999 14:31:26 +0100
To: robbie@scot-mur.demon.co.uk
Message-Id: <E10snsc-00003K-00@mailserver.scot-mur.demon.co.uk>
From: root <root@scot-mur.demon.co.uk>
Date: Sat, 12 Jun 1999 14:31:26 +0100
X-UIDL: 3712335ed80e61c2493a8e41430aed9c
Linux version 2.2.9 (root@linux) (gcc version egcs-2.91.66 Debian GNU/Linux (egcs-1.1.2 release)) #1 Sat Jun 12 07:31:08 BST 1999
Console: colour VGA+ 80x25
Calibrating delay loop... 49.97 BogoMIPS
Memory: 63436k/65536k available (732k kernel code, 408k reserved, 920k data, 40k init)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
CPU: 486
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xf6f41
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: 00:91 [1060/673a]: Working around UM8886BF bugs
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
Starting kswapd v 1.5
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.09
UM8886A: IDE controller on PCI bus 00 dev 90
UM8886A: not 100% native mode: will probe irqs later
UM8886BF: IDE controller on PCI bus 00 dev 91
UM8886BF: not 100% native mode: will probe irqs later
UM8886BF: port 0x01f0 already claimed by ide0
UM8886BF: port 0x0170 already claimed by ide1
UM8886BF: neither IDE port enabled (BIOS)
hda: ST31722A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ST31722A, 1625MB w/128kB Cache, CHS=3303/16/63
Floppy drive(s): fd0 is 1.44M
FDC 0 is an 8272A
IP-Config: No network devices available.
Partition check:
hda: hda1 hda2 hda3 hda4
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 40k freed
Adding Swap: 33260k swap-space (priority -1)
smc-ultra.c: Presently autoprobing (not recommended) for a single card.
smc-ultra.c:v2.02 2/3/98 Donald Becker (becker@cesdis.gsfc.nasa.gov)
eth0: SMC Ultra at 0x300, 00 00 C0 48 CC A1, IRQ 10 memory 0xcc000-0xcffff.
CSLIP: code copyright 1989 Regents of the University of California
PPP: version 2.3.7 (demand dialling)
PPP line discipline registered.
registered device ppp0
--e5bfZ/T2xnjpUIbw--
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/