P.S. is there any thing that can be done about the ide/DMA/ide hard drive
problem?
System...
Suse 6.0
kernel 2.2.1
all ide drives..2 4gbs HD
1 atapi with ide-scsi CDROM
1 CDRW atapi with ide-scsi
1 zip atapi with ide-scsi
200 Mhz k6..lalala the rest is in the boot.msg file
Inspecting /boot/System.map
Loaded 6763 symbols from /boot/System.map.
Symbols match kernel version 2.2.1.
No module symbols loaded.
klogd 1.3-3, log source = /proc/kmsg started.
<4>Linux version 2.2.1 (root@BS28-222-095) (gcc version egcs-2.91.60 19981201 (egcs-1.1.1 release)) #7 Sat Feb 13 22:33:44 EST 1999
<4>Detected 225004308 Hz processor.
<4>Console: colour VGA+ 80x25
<4>Calibrating delay loop... 448.92 BogoMIPS
<4>Memory: 79468k/81920k available (968k kernel code, 408k reserved, 1020k data, 56k init)
<4>CPU: AMD AMD-K6tm w/ multimedia extensions stepping 02
<6>Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
<6>Checking 'hlt' instruction... OK.
<4>POSIX conformance testing by UNIFIX
<4>PCI: PCI BIOS revision 2.10 entry at 0xfb480
<4>PCI: Using configuration type 1
<4>PCI: Probing PCI hardware
<4>PCI: 00:38 [1106/0586]: Work around ISA DMA hangs (00)
<6>Activating ISA DMA hang workarounds.
<6>Linux NET4.0 for Linux 2.2
<6>Based upon Swansea University Computer Society NET3.039
<6>NET4: Unix domain sockets 1.0 for Linux NET4.0.
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP
<4>Starting kswapd v 1.5
<6>parport0: PC-style at 0x378 [SPP,PS2]
<6>Detected PS/2 Mouse Port.
<6>Serial driver version 4.27 with no serial options enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>ttyS01 at 0x02f8 (irq = 3) is a 16550A
<7>Sound initialization started
<4><Crystal audio controller (CS4236)> at 0x534 irq 5 dma 1,0
<4><MPU-401 (UART) MIDI> at 0x330 irq 9
<7>Sound initialization complete
<4>VP_IDE: IDE controller on PCI bus 00 dev 39
<4>VP_IDE: not 100% native mode: will probe irqs later
<4> ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
<4> ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
<4>AEC6210: IDE controller on PCI bus 00 dev 40
<4>AEC6210: not 100% native mode: will probe irqs later
<6>AEC6210: ROM enabled at 0xe7000000
<4> ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio
<4> ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio
<4>hda: WDC AC34300L, ATA DISK drive
<4>hdc: QUANTUM BIGFOOT_CY4320A, ATA DISK drive
<4>hdd: Memorex CRW-1622, ATAPI CDROM drive
<4>hde: UCDJ V2.B, ATAPI CDROM drive
<4>hdf: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>ide1 at 0x170-0x177,0x376 on irq 15
<4>ide2 at 0xd800-0xd807,0xdc02 on irq 11
<6>hda: WDC AC34300L, 4104MB w/256kB Cache, CHS=523/255/63, UDMA
<6>hdc: QUANTUM BIGFOOT_CY4320A, 4134MB w/67kB Cache, CHS=8960/15/63
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<4>scsi0 : SCSI host adapter emulation for IDE ATAPI devices
<4>scsi : 1 host.
<4> Vendor: IOMEGA Model: ZIP 100 Rev: 13.A
<4> Type: Direct-Access ANSI SCSI revision: 00
<4>Detected scsi removable disk sda at scsi0, channel 0, id 0, lun 0
<4> Vendor: Memorex Model: CRW-1622 Rev: D2.3
<4> Type: CD-ROM ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
<4> Vendor: UCDJ Model: Rev: V2.B
<4> Type: CD-ROM ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr1 at scsi0, channel 0, id 2, lun 0
<4>scsi : detected 2 SCSI cdroms 1 SCSI disk total.
<4>sr0: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
<6>Uniform CDROM driver Revision: 2.52
<4>sr1: scsi3-mmc drive: 1x/8x tray
<4>SCSI device sda: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB]
<4>sda: Write Protect is off
<4>Partition check:
<4> sda: sda1
<4> hda: hda1 hda2 hda3
<4> hdc: hdc1
<4> hdf:<3>ide-scsi: hdf: unsupported command in request queue (0)
<4>end_request: I/O error, dev 21:40 (hdf), sector 0
<4> unable to read partition table
<5>NTFS version 990102
<4>VFS: Mounted root (ext2 filesystem) readonly.
<4>Freeing unused kernel memory: 56k freed
<6>Adding Swap: 88352k swap-space (priority -1)
Kernel logging (proc) stopped.
Kernel log daemon terminating.
--
Nicholas Henke
University of Pennsylvania
Class of 2002
215-417-6418
Linux User # 97849
----------------------
"To be sure of hitting the target, shoot first, and call whatever you hit the target"
----------------------
"I'm confused, but it's working, and I'm sure I'll understand it eventually."
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/