I can read Cds fine, and can use all the 3 device in normal ways,
if I
1./ do not try to write a CD
2./ do not give the command
#scsiinfo -s /dev/sdb (that is the ZIP drive)
Unfortunately I did not bother with kernel symbols.
*********************
l: Starting kswapd v 1.5
l: Serial driver version 4.27 with no serial options enabled
l: ttyS00 at 0x03f8 (irq = 4) is a 16550A
l: ttyS01 at 0x02f8 (irq = 3) is a 16550A
l: EATA/DMA 2.0x: Copyright (C) 1994-1998 Dario Ballabio.
l: EATA config options -> tc:y, lc:y, mq:16, eh:y, rs:y, et:n.
l: EATA0: 2.0C, PCI 0x6510, IRQ 10, BMST, SG 122, MB 64.
l: EATA0: wide SCSI support enabled, max_id 16, max_lun 8.
l: EATA0: SCSI channel 0 enabled, host target ID 7.
l: scsi0 : EATA/DMA 2.0x rev. 4.33.00
l: scsi : 1 host.
l: Vendor: IBM Model: DCAS-34330W Rev: S65A
l: Type: Direct-Access ANSI SCSI revision: 02
l: Detected scsi disk sda at scsi0, channel 0, id 4, lun 0
l: Vendor: IOMEGA Model: ZIP 100 Rev: E.08
l: Type: Direct-Access ANSI SCSI revision: 02
l: Detected scsi removable disk sdb at scsi0, channel 0, id 5, lun 0
l: Vendor: MATSHITA Model: CD-R CW-7502 Rev: 4.10
l: Type: CD-ROM ANSI SCSI revision: 02
l: EATA0: scsi0, channel 0, id 4, lun 0, cmds/lun 16, sorted, tagged.
l: EATA0: scsi0, channel 0, id 5, lun 0, cmds/lun 16, sorted.
l: EATA0: scsi0, channel 0, id 6, lun 0, cmds/lun 16, sorted.
l: scsi : detected 2 SCSI disks total.
l: SCSI device sda: hdwr sector= 512 bytes. Sectors= 8466688 [4134 MB] [4.1 GB]
l: SCSI device sdb: hdwr sector= 512 bytes. Sectors= 196608 [96 MB] [0.1 GB]
l: sdb: Write Protect is off
l: ne2k-pci.c:v0.99L 2/7/98 D. Becker/P. Gortmaker
http://cesdis.gsfc.nasa.gov/ll: ne2k-pci.c: PCI NE2000 clone 'RealTek
RTL-8029' at I/O 0x6600, IRQ 15.
l: eth0: PCI NE2000 found at 0x6600, IRQ 15, 00:00:B4:56:38:00.
l: Partition check:
l: sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 >
l: sdb: sdb1
l: VFS: Mounted root (ext2 filesystem) readonly.
l: Freeing unused kernel memory: 32k freed
l: Adding Swap: 83076k swap-space (priority -1)
l: Detected scsi CD-ROM sr0 at scsi0, channel 0, id 6, lun 0
l: sr0: scsi3-mmc drive: 8x/8x writer xa/form2 cdda tray
l: Uniform CDROM driver Revision: 2.51
l: sr0: disc change detected.
l: VFS: Disk change detected on device sr(11,0)
l: Uniform CD-ROM driver unloaded
=========== CD writing (cdrecord-1.6.1 compiled with glibc-2.0.6)
l: EATA0: reset, enter, target 0.6:0, pid 64646.
l: EATA0: reset, pid 64646 inactive.
l: EATA0: reset, board reset done, enabling interrupts.
l: EATA0: reset, interrupts disabled, loops 99913.
l: EATA0: reset, exit.
l: Unable to handle kernel paging request at virtual address c38199c8
l: current->tss.cr3 = 00101000, %cr3 = 00101000
l: *pde = 0009c063
l: *pte = 00000000
l: Oops: 0000
l: CPU: 0
l:
***********************************
after this the system remains in working condition.
I only loose the CD device, and (scsi_eh_0) usually becomes zombie.
Under 2.0.36 CD writing seems to work, with scsiinfo I have the
same problem.
Holluby Istvan Budapest
(holluby@mail.matav.hu)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/