Re: 2.2.0 pre5-ac1 tulip.c

Katlun Yong (katlun@home.com)
Sat, 09 Jan 1999 06:07:09 -0500

--------------B36C3D84D09FC9B931CC0E3D
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit

Finally, it works!!

dhcpcd-1.3.7

and in conf.modules:

alias net-pf-17 af_packet

Katlun Yong wrote:

>
>
>
> I have a linksys etherfast 10/100.
>
> using dhcp with a cable modem for @home
>
> Works under 2.0.36 but not 2.2.0-pre4-ac1
>
> Any clues?
>
> For 2.0.36
> klogd report as:
>
> tulip.c:v0.89H 5/23/98 becker@cesdis.gsfc.nasa.gov
> eth0: Lite-On 82c168 PNIC at 0xec00, 00 a0 cc 22 28 0a, IRQ 5.
> eth0: MII transceiver found at MDIO address 1, config 3100 status
> 7829.
> eth0: Advertising 01e1 on PHY 1, previously advertising 01e1.
>
> eth0: Changing PNIC configuration to half-duplex, CSR6 816e0000
>
> using tulip-diag.c :
>
> tulip-diag.c:v1.06 9/18/98 Donald Becker (becker@cesdis.gsfc.nasa.gov)
>
> Digital DC21040 Tulip Tulip chip registers at 0xec00:
> 00008000 01ff0000 01000608 00459028 00459228 02660010 816e2002
> 0001ebef
> 00000000 00000000 00459228 0045b60c 00000025 00000000 00000000
> 10000001
> The Rx process state is 'Waiting for packets'.
> The Tx process state is 'Idle'.
> Transmit started, Receive started, half-duplex.
> The transmit unit is set to store-and-forward.
> Port selection is MII 100baseTx scrambler, half-duplex.
>
> 2.2.0-pre5-ac1
>
> tulip.c:v0.89H 5/23/98 becker@cesdis.gsfc.nasa.gov
> eth0: Lite-On 82c168 PNIC at 0xec00, 00 a0 cc 22 28 0a, IRQ 5.
> eth0: MII transceiver found at MDIO address 1, config 3100 status
> 7829.
> eth0: Advertising 01e1 on PHY 1, previously advertising 01e1.
>
> etho: Using DHCP failed.
>
> tulip-diag.c:v1.06 9/18/98 Donald Becker (becker@cesdis.gsfc.nasa.gov)
>
> Digital DC21040 Tulip Tulip chip registers at 0xec00:
> 00000000 01ff0000 0008ffff 00000000 00000000 02000112 01440040
> 00000000
> 00000000 00000000 00000000 00000000 00000025 00000000 00000000
> 10000000
> The Rx process state is 'Stopped'.
> The Tx process state is 'Stopped'.
> Transmit stopped, Receive stopped, half-duplex.
> The transmit threshold is 72.
> Port selection is MII 100baseTx scrambler, half-duplex.
>
>
>

--------------B36C3D84D09FC9B931CC0E3D
Content-Type: text/html; charset=us-ascii
Content-Transfer-Encoding: 7bit

<!doctype html public "-//w3c//dtd html 4.0 transitional//en">
Finally, it works!!

dhcpcd-1.3.7

and in conf.modules:

alias net-pf-17 af_packet
 
 
 
 
 
 
 
 
 
 

Katlun Yong wrote:

 
  
I have a linksys  etherfast 10/100.

using dhcp with a cable modem for @home

Works under 2.0.36  but not 2.2.0-pre4-ac1
Any clues?
For 2.0.36
klogd report as:

tulip.c:v0.89H 5/23/98 becker@cesdis.gsfc.nasa.gov
eth0: Lite-On 82c168 PNIC at 0xec00, 00 a0 cc 22 28 0a, IRQ 5.
eth0:  MII transceiver found at MDIO address 1, config 3100 status 7829.
eth0:  Advertising 01e1 on PHY 1, previously advertising 01e1.

eth0: Changing PNIC configuration to half-duplex, CSR6 816e0000

using tulip-diag.c :

tulip-diag.c:v1.06 9/18/98 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Digital DC21040 Tulip Tulip chip registers at 0xec00:
  00008000 01ff0000 01000608 00459028 00459228 02660010 816e2002 0001ebef
  00000000 00000000 00459228 0045b60c 00000025 00000000 00000000 10000001
 The Rx process state is 'Waiting for packets'.
 The Tx process state is 'Idle'.
Transmit started, Receive started, half-duplex.
 The transmit unit is set to store-and-forward.
 Port selection is MII 100baseTx scrambler, half-duplex.

2.2.0-pre5-ac1

tulip.c:v0.89H 5/23/98 becker@cesdis.gsfc.nasa.gov
eth0: Lite-On 82c168 PNIC at 0xec00, 00 a0 cc 22 28 0a, IRQ 5.
eth0:  MII transceiver found at MDIO address 1, config 3100 status 7829.
eth0:  Advertising 01e1 on PHY 1, previously advertising 01e1.

etho: Using DHCP failed.

tulip-diag.c:v1.06 9/18/98 Donald Becker (becker@cesdis.gsfc.nasa.gov)
Digital DC21040 Tulip Tulip chip registers at 0xec00:
  00000000 01ff0000 0008ffff 00000000 00000000 02000112 01440040 00000000
  00000000 00000000 00000000 00000000 00000025 00000000 00000000 10000000
 The Rx process state is 'Stopped'.
 The Tx process state is 'Stopped'.
Transmit stopped, Receive stopped, half-duplex.
 The transmit threshold is 72.
 Port selection is MII 100baseTx scrambler, half-duplex.
 
 
 

--------------B36C3D84D09FC9B931CC0E3D--

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/