request_module[parport_lowlevel]: Root fs not mounted
lp: driver loaded but no devices found
I am not subscribed to the linux-kernel mailing list, please CC me any
replies. This is my first post here so I apologize for any mistakes I
might've made as a newbie.
I have not applied the pre5-ac1 patch because I do not know how my
OSS/Opensound installation will react to that.
here is the whole boot-up screen (dmesg):
Linux version 2.2.0-pre5 (root@pinhead) (gcc version egcs-2.91.60
19981201 (egcs-1.1.1 release)) #2 Thu Jan 7 19:37:51 EST 1999
Detected 400920069 Hz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 399.77 BogoMIPS
Memory: 128144k/131072k available (708k kernel code, 408k reserved,
1764k data, 48k init)
CPU: Intel Pentium II (Deschutes) stepping 02
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.26 (19981001) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xfdb91
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Enabling I/O for device 00:3a
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
Starting kswapd v 1.5
vesafb: framebuffer at 0xe6000000, mapped to 0xc8800000, size 8192k
vesafb: mode is 1024x768x8, linelength=1024, pages=8
vesafb: protected mode interface info at c000:7780
vesafb: pmi: set display start = c00c77cf, set palette = c00c77fa
vesafb: pmi: ports = 3c0 3c4 3c5 3c7 3c8 3c9 3d4 3d5 3d6 3d7 3d8 3d9 3da
vesafb: scrolling: ypan using protected mode interface,
yres_virtual=8192
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Serial driver version 4.27 with no serial options enabled
ttyS03 at 0x02e8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
request_module[parport_lowlevel]: Root fs not mounted
lp: driver loaded but no devices found
Real Time Clock Driver v1.09
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: ST38641A, ATA DISK drive
hdb: WDC AC34300L, ATA DISK drive
hdc: TOSHIBA CD-ROM XM-6302B, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: ST38641A, 8207MB w/128kB Cache, CHS=1046/255/63, UDMA
hdb: WDC AC34300L, 4104MB w/256kB Cache, CHS=523/255/63, UDMA
hdc: ATAPI 32X CDROM drive, 256kB Cache
Uniform CDROM driver Revision: 2.51
Partition check:
hda:hda: set_multmode: status=0x51 { DriveReady SeekComplete Error }
hda: set_multmode: error=0x04 { DriveStatusError }
hda1 hda2 < hda5 hda6 hda7 hda8 >
hdb: hdb1 hdb2 hdb3 hdb4
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 48k freed
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/