I recently upgraded to 2.0.34 from 2.0.33 (IPI warnings but never crashed)
I have a digiboard with 40 dialin modem.
The following is a dmesg output to understanding my machine configuration:
*******************************BEGIN OF DMESG*****************************
PCI BIOS revision 2.10 entry at 0xfb3c0
Probing PCI hardware.
Calibrating delay loop.. ok - 80.08 BogoMIPS
Memory: 63124k/65536k available (756k kernel code, 384k reserved, 1272k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: ICMP, UDP, TCP
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Intel Pentium with F0 0F bug - workaround enabled.
alias mapping IDT readonly ... ... done
Linux version 2.0.34 (root@mazinga) (gcc version 2.7.2.3) #1 Thu Jul 2 11:17:48 CEST 1998
Booting processor 1 stack 00002000: Calibrating delay loop.. ok - 80.08 BogoMIPS
Total of 2 processors activated (160.15 BogoMIPS).
Starting kswapd v 1.4.2.2
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
DIGI epca driver version 1.3.0 loaded.
PS/2 auxiliary pointing device detected -- driver installed.
ide: i82371 PIIX (Triton) on PCI bus 0 function 57
ide0: BM-DMA at 0xf000-0xf007
ide1: BM-DMA at 0xf008-0xf00f
hdd: CD-ROM TW 120D, ATAPI CDROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
(scsi0) <Adaptec AIC-7880 Ultra SCSI host adapter> found at PCI 12/0
(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi0) BIOS enabled, IO Port 0x6200, IRQ 9
(scsi0) IO Memory at 0xe4101000, MMAP Memory at 0x4809000
(scsi0) Resetting channel
(scsi0) Downloading sequencer code... 413 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.0.14/3.2.4
<Adaptec AIC-7880 Ultra SCSI host adapter>
scsi : 1 host.
(scsi0:0:-1:-1) Scanning channel for devices.
(scsi0:0:8:0) Using wide (16 bit) transfers.
(scsi0:0:8:0) Synchronous at 10.0MHz, offset 8.
Vendor: SEAGATE Model: ST410800W Rev: 0006
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 8, lun 0
(scsi0:0:9:0) Using wide (16 bit) transfers.
(scsi0:0:9:0) Synchronous at 10.0MHz, offset 8.
Vendor: SEAGATE Model: ST410800W Rev: 0006
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 9, lun 0
scsi : detected 2 SCSI disks total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17755614 [8669 MB] [8.7 GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 17755614 [8669 MB] [8.7 GB]
PPP: version 2.2.0 (dynamic channel allocation)
TCP compression code copyright 1989 Regents of the University of California
PPP Dynamic channel allocation code copyright 1995 Caldera, Inc.
PPP line discipline registered.
eepro100.c:v0.99B 4/7/98 Donald Becker linux-eepro100@cesdis.gsfc.nasa.gov
eth0: Intel EtherExpress Pro 10/100 at 0x6100, 00:A0:C9:42:96:01, IRQ 11.
Board assembly 667280-003, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x49caa8d6).
Receiver lock-up workaround activated.
eepro100.c:v0.99B 4/7/98 Donald Becker linux-eepro100@cesdis.gsfc.nasa.gov
Partition check:
sda: sda1 sda2
sdb: sdb1
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 130748k swap-space (priority -1)
Digi PC/Xx Driver V1.3.0: PC/Xem I/O = 0x104 Mem = 0xd0000 Ports = 48
registered device ppp0
registered device ppp1
registered device ppp2
registered device ppp3
registered device ppp4
registered device ppp5
registered device ppp6
registered device ppp7
registered device ppp8
registered device ppp9
registered device ppp10
registered device ppp11
registered device ppp12
registered device ppp13
registered device ppp14
*******************************END OF DMESG******************************
How can i fix the problem ???
Thanks... <ranaldo@unina.it>
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.rutgers.edu
Please read the FAQ at http://www.altern.org/andrebalsa/doc/lkml-faq.html