--Steve
Command line: bootdevice=sda2 bootfile=vmlinux-2.0.32.gz ether=0,0,eth1
Alpha PCI BIOS32 revision 0.03
Probing PCI hardware.
SMC FDC37C93X Ultra I/O Controller found @ 0x370
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
Calibrating delay loop.. ok - 497.03 BogoMIPS
Memory: 61872k available
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP
Linux version 2.0.32 (root@icarus.icarus.com) (gcc version 2.7.2.3) #2 Fri Jan 16 23:16:24 PST 1998
Starting kswapd v 1.4.2.2
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
PS/2 auxiliary pointing device detected -- driver installed.
Ramdisk driver initialized : 16 ramdisks of 4096K size
hda: WDC AC22100H, 2014MB w/128kB Cache, CHS=4092/16/63
hdb: FX120T, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 2.88M
FDC 0 is a post-1991 82077
aic7xxx: <Adaptec AHA-294X Ultra SCSI host adapter> at PCI 6
aic7xxx: Warning - detected auto-termination. Please verify driver
detected settings and use manual termination if necessary.
aic7xxx: BIOS enabled, IO Port 0x8800, IO Mem 0xc000000, IRQ 16, Revision B
aic7xxx: Wide Channel, SCSI ID 7, 16/16 SCBs, QFull 16, QMask 0x1f
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 4.1/3.2
scsi : 1 host.
scsi0: Scanning channel A for devices.
Vendor: Quantum Model: XP32150W Rev: L912
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi0: Sending SDTR!!
Vendor: SEAGATE Model: ST15230N Rev: 0058
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
scsi0: Target 2, channel A, refusing WIDE negotiation; using 8 bit transfers.
Vendor: MATSHITA Model: PD-1 LF-1001 Rev: A105
Type: Optical Device ANSI SCSI revision: 02
Detected scsi removable disk sdc at scsi0, channel 0, id 2, lun 0
Vendor: MATSHITA Model: PD-1 LF-1001 Rev: A105
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 1
scsi : detected 1 SCSI cdrom 3 SCSI disks total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 4406960 [2151 MB] [2.2 GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8386733 [4095 MB] [4.1 GB]
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 1298496 [634 MB] [0.6 GB]
sdc: Write Protect is off
eth0: 3c509 at 0x300 tag 1, 10baseT port, address 00 60 97 1a e3 ab, IRQ 11.
3c509.c:1.12 6/4/97 becker@cesdis.gsfc.nasa.gov
eth1: DE450-CA at 0x9000 (PCI bus 0, device 5), h/w address 00:00:f8:02:04:34,
and requires IRQ18 (provided by PCI BIOS).
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sdb: sdb1 sdb2 sdb3 sdb4
sdc: sdc1
hda: hda1 hda2 < hda5 hda6 >
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 80312k swap-space (priority -1)
Adding Swap: 134792k swap-space (priority -2)
eth0: Setting Rx mode to 1 addresses.