hda: CPQ001373 Drive Array Controller, ATA
hdb: CPQ001373 Drive Array Controller, ATA
with endless printouts of:
Interrupt lock in context c010ac49
Interrupt lock in context c010ac49
Interrupt lock in context c010ac49
...
Where c010ac49 is:
c010ac30 T math_error
c010acf8 T do_coprocessor_error
--- It works in 2.0.30, and I provide dmesg output for 2.0.30 below:klogd 1.3-3, log source = /proc/kmsg started. Cannot find map file. Loaded 45 symbols from 3 modules. Console: 16 point font, 400 scans Console: colour VGA+ 80x25, 1 virtual console (max 63) Calibrating delay loop.. ok - 6.60 BogoMIPS Memory: 14792k/16256k available (580k kernel code, 384k reserved, 500k data) Swansea University Computer Society NET3.035 for Linux 2.0 NET3: Unix domain sockets 0.13 for Linux NET3.035. Swansea University Computer Society TCP/IP for NET3.034 IP Protocols: ICMP, UDP, TCP Checking 386/387 coupling... Ok, fpu using old IRQ13 error reporting Checking 'hlt' instruction... Ok. Linux version 2.0.30 (root@flash.uucp.dtek.chalmers.se) (gcc version 2.7.2.1) #3 Fri Apr 11 01
hda: CPQ001373 Drive Array Controller, 810MB w/128kB Cache, CHS=823/32/63 hdb: CPQ001373 Drive Array Controller, 405MB w/128kB Cache, CHS=823/16/63 ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Floppy drive(s): fd0 is 1.44M Started kswapd v 1.4.2.2 FDC 0 is a pre-1991 82077 md driver 0.35 MAX_MD_DEV=4, MAX_REAL=8 aic7xxx: Chip reset not cleared; clearing manually. aic7xxx: Extended translation disabled. aic7xxx: AHA-2740 Rev C and previous. aic7xxx: Memory check yields 4 SCBs, paging not enabled. aic7xxx: Using edge triggered interrupts. aic7xxx: Enabled channel B of AHA-2740-Twin. AHA-2740-TWIN AT EISA SLOT 5: irq 15 bus release time 12 bclks data fifo threshold 100 SCSI CHANNEL A: scsi id 7 scsi selection timeout 64 ms scsi bus reset at power-on enabled scsi bus parity enabled scsi bus termination (low byte) disabled aic7xxx: Downloading sequencer code...done. scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 4.0/3.2/4.0 scsi : 1 host. scsi0: Scanning channel A for devices. scsi0: Target 1, channel A, now synchronous at 10.0MHz, offset 15. Vendor: CONNER Model: CFP1060S 1.05GB Rev: 203C Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sda at scsi0, channel 0, id 1, lun 0 scsi0: Target 2, channel A, now synchronous at 10.0MHz, offset 15. Vendor: SEAGATE Model: ST11900N Rev: 9700 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdb at scsi0, channel 0, id 2, lun 0 scsi0: Scanning channel B for devices. scsi0: Target 2, channel B, now synchronous at 5.0MHz, offset 15. Vendor: ARCHIVE Model: Python 25947-XXX Rev: 2.49 Type: Sequential-Access ANSI SCSI revision: 02 scsi : detected 2 SCSI disks total. SCSI device sda: hdwr sector= 512 bytes. Sectors= 2074880 [1013 MB] [1.0 GB] SCSI device sdb: hdwr sector= 512 bytes. Sectors= 3310215 [1616 MB] [1.6 GB] Ethernet Bridge 002 for NET3.035 (Linux 2.0) eth0: 3c509 at 0x6000 tag 0, AUI port, address 00 20 af 73 e1 a1, IRQ 5. 3c509.c:1.07 6/15/95 becker@cesdis.gsfc.nasa.gov Partition check: sda: sda1 < sda5 sda6 sda7 > sda2 sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8 hda: hda1 < hda5 hda6 > hda2 hda3 hdb: hdb1 < hdb5 > VFS: Mounted root (ext2 filesystem) readonly. Adding Swap: 41964k swap-space (priority -1) EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended Detected scsi tape st0 at scsi0, channel 1, id 2, lun 0
--Fredrik Lundholm exce7@ce.chalmers.se