Re: [PATCH v2] clk: sunxi-ng: a733: Keep SCP firmware bus clocks enabled
From: Andre Przywara
Date: Wed Nov 18 2026 - 09:51:59 EST
Hi,
On 11/18/26 14:41, Chen-Yu Tsai wrote:
On Wed, Nov 18, 2026 at 1:18 AM Andre Przywara <andre.przywara@xxxxxxx> wrote:
Hi,
the patch itself looks fine, but the comments and the commit message are
not entirely correct, I think.
On 11/12/26 22:38, Enzo Adriano wrote:
The A733 PRCM's bus-r-riscv and bus-r-msgbox gates have no Linux
consumers, so unused-clock cleanup gates them. With vendor SCP firmware
running on the E902 as shipped on Cubie A7S, warm reboot then stalls.
Please note that we don't support "vendor firmware" with mainline Linux.
That was mostly incompatible in the past, and while it might work these
days, this is not something we control and want to endorse.
So we would be quite reluctant (to put it mildly) about merging patches
that are solely needed for BSP firmware bits.
Keep both critical until remoteproc/mailbox drivers can claim them.
I don't think this "until" is an argument. Even if we'd have Linux
driver support, they would be optional to use (not compiled, not
loaded), and would only be needed to *communicate* with the firmware.
But those clocks are actually there to drive the RISC-V core clock, and
also the "RISC-V side" of the peripherals, due to a lack of separate
clock controls in the SoC in the Allwinner design. So the kernel should
not care about or touch those clocks at all - which is what
CLK_IS_CRITICAL does.
No. CLK_IS_CRITICAL also tells the kernel to turn it on, and you then
can never turn it off. You get a big warning if you try to defeat the
refcounting, but nothing else happens.
Good point, so is CLK_IGNORE_UNUSED a better flag? As far as I can see, it only prevents turning it off if unclaimed, it doesn't turn it on if it was off initially, and it doesn't disallow turning it off.
So what if the *real* remoteproc driver needs to turn the clock off to
pause the RISC-V core? It can't
I guess this depends on the use case, which isn't very well defined. If this E902 is really a remoteproc device entirely controlled by Linux, then sure: Linux should have full control over its clock.
But if it's running some kind of firmware component, then the kernel shouldn't mess with it, IMHO. But I think there is still the arisc on the A733, so this would more likely run the management processor (SCP) code?
Cheers,
Andre
So, not a fan of this. If the loaded firmware somehow needs some resources
then perhaps the software that loaded it needs to somehow tell the kernel
they are needed, like the bootloader patching the DT passed to the kernel.
If the firmware needs a piece of DRAM, you don't say in the kernel that
this piece of DRAM is off-limits. You let the bootloader tell the kernel.
Static DRAM carve outs with reserved-memory nodes in the DT source is also
ugly, as you could end up with mismatches if the firmware somehow changed.
IMO CLK_IS_CRITICAL should be used for things that the kernel knows it needs
but there's nothing to claim it.
ChenYu
This follows A523 bus-r-cpucfg in commit 1dba74abf3e2 ("clk: sunxi-ng:
Mark A523 bus-r-cpucfg clock as critical") and the temporary SCPI firmware
clock protection for Meson AXG fclk_div3 in drivers/clk/meson/axg.c.
On Cubie A7S with vendor boot0/BL31/SCP/U-Boot and without
clk_ignore_unused, warm reboot returns with both clocks critical and
stalls without them. Vinicius found either flag alone insufficient on
Cubie A7Z. Power-off, suspend, single flags on A7S, other
boards/firmware and upstream TF-A were not tested.
Link: https://lore.kernel.org/r/20261005183038.417798-1-vinicius.eduardo.pedrosa@xxxxxxxxx
Signed-off-by: Enzo Adriano <enzo.adriano.code@xxxxxxxxx>
---
Changes in v2:
- Drop r-timer0, bus-r-timer and bus-msgbox0: A7S warm reboot works with
these at 0/0. Keep only the two E902/mailbox bus gates after Junhui's
review, pending remoteproc/mailbox ownership.
- Rebase on CCU v7; its PRCM clock definitions are unchanged from v6.
v1:
https://lore.kernel.org/r/20261031020640-263f7b05-a7s-clock@xxxxxxxxx
Base: v7.4-rc1. Depends on CCU v7 (all eight patches):
https://lore.kernel.org/r/20261112-a733-clk-v7-0-db7c5451ffa2@xxxxxxxxxxxxx
November 12 board test: two RAM boots and warm reboot -f returns on
Cubie A7S with vendor boot0/BL31/SCP/U-Boot, without clk_ignore_unused.
Both retained clocks were 1/1; all three dropped clocks were 0/0.
The no-flag stall was observed with CCU v6 on Nov 10; PRCM code is
byte-identical in v7, where the no-flag control was not repeated.
Runtime used DT v3 and its dependencies (all four UART v2 patches),
with the PMIC identifier and pinctrl IRQ-map context adapted to the base:
https://lore.kernel.org/r/cover.1794227241.git.enzo.adriano.code@xxxxxxxxx
I don't think there is any need for those longish test descriptions,
especially if they pass.
drivers/clk/sunxi-ng/ccu-sun60i-a733-r.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/drivers/clk/sunxi-ng/ccu-sun60i-a733-r.c b/drivers/clk/sunxi-ng/ccu-sun60i-a733-r.c
index b8f6e8c6e507..f2965daba0d3 100644
--- a/drivers/clk/sunxi-ng/ccu-sun60i-a733-r.c
+++ b/drivers/clk/sunxi-ng/ccu-sun60i-a733-r.c
@@ -108,7 +108,9 @@ static SUNXI_CCU_DUALDIV_MUX_GATE(r_spi_clk, "r-spi", r_spi_parents, 0x150,
0);
static SUNXI_CCU_GATE_HW(bus_r_spi_clk, "bus-r-spi", &r_ahb_clk.common.hw, 0x15c, BIT(0), 0);
-static SUNXI_CCU_GATE_HW(bus_r_msgbox_clk, "bus-r-msgbox", &r_ahb_clk.common.hw, 0x17c, BIT(0), 0);
+/* Vendor SCP firmware on E902 needs this until a remoteproc/mailbox driver claims it. */
Please change this comment. Something like the msgbox clock is shared
between the E902 core and the Arm APs.
+static SUNXI_CCU_GATE_HW(bus_r_msgbox_clk, "bus-r-msgbox", &r_ahb_clk.common.hw,
+ 0x17c, BIT(0), CLK_IS_CRITICAL);
static SUNXI_CCU_GATE_HW(bus_r_uart0_clk, "bus-r-uart0", &r_apb1_clk.common.hw, 0x18c, BIT(0), 0);
static SUNXI_CCU_GATE_HW(bus_r_uart1_clk, "bus-r-uart1", &r_apb1_clk.common.hw, 0x18c, BIT(1), 0);
@@ -146,8 +148,9 @@ static SUNXI_CCU_MUX_DATA_WITH_GATE(r_riscv_clk, "r-riscv", r_riscv_parents, 0x2
24, 2, /* mux */
BIT(31), /* gate */
0);
+/* Vendor SCP firmware on E902 needs this until a remoteproc/mailbox driver claims it. */
and this. Just note that the E902 might be running on its own, in a pure
firmware role, or even completely separate from the main kernel.
Oh, and also please put somewhere that this is based on the linux-sunxi
for-next tree, aside from just having the base-commit ID below.
Cheers,
Andre
static SUNXI_CCU_GATE_HW(bus_r_riscv_clk, "bus-r-riscv", &r_apb0_clk.common.hw,
- 0x21c, BIT(0), 0);
+ 0x21c, BIT(0), CLK_IS_CRITICAL);
static SUNXI_CCU_GATE_HW(bus_r_riscv_cfg_clk, "bus-r-riscv-cfg", &r_apb0_clk.common.hw,
0x21c, BIT(1), 0);
base-commit: 6628e7d4c6b25c8d18f1345e3a20d21829aae7e4