[PATCH v7 9/9] arm64: dts: rockchip: add the dcphy mipi csi-2 receiver nodes to rk3588
From: Jason Yang
Date: Wed Nov 18 2026 - 00:56:28 EST
The MIPI0 and MIPI1 receiver units are connected to MIPI DCPHY0 and
MIPI DCPHY1, whose receiver side is now supported. Add the two nodes and
wire them to the VICAP ports.
The csi nodes select the PHY receiver with the new PHY_DIRECTION_RX from
the dt-bindings header. The phy nodes need no phy-type: the DSI host and
the CSI-2 host both run the block in D-PHY mode, the default.
PHY_DIRECTION_RX is an ABI change: an older kernel takes any cell value
as the mode of the block. The csi nodes are disabled, so an older kernel
is not affected until a board enables csi0 or csi1.
Before v7.0, there is no CSI-2 host driver, so enabling csi0 or csi1
changes nothing. Since v7.0, a CSI-2 host driver probes the enabled csi
nodes. An older PHY driver then gives the CSI-2 host the PHY transmitter
that drives the display. The camera gets no frames, and the display can
stop working as well.
Signed-off-by: Jason Yang <jason98166@xxxxxxxxx>
Reviewed-by: Michael Riesch <michael.riesch@xxxxxxxxxxxxx>
Tested-by: Quentin Schulz <quentin.schulz@xxxxxxxxx> # RK3588 Tiger CSI1 2-lane IMX219, CSI0 2-lane OV5675+DSI
---
arch/arm64/boot/dts/rockchip/rk3588-base.dtsi | 68 +++++++++++++++++++++++++++
1 file changed, 68 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-base.dtsi b/arch/arm64/boot/dts/rockchip/rk3588-base.dtsi
index aa69fd3793fd..c7174c2f15c3 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-base.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588-base.dtsi
@@ -1516,10 +1516,18 @@ vicap_dvp: port@0 {
vicap_mipi0: port@1 {
reg = <0x1>;
+
+ vicap_mipi0_input: endpoint {
+ remote-endpoint = <&csi0_output>;
+ };
};
vicap_mipi1: port@2 {
reg = <0x2>;
+
+ vicap_mipi1_input: endpoint {
+ remote-endpoint = <&csi1_output>;
+ };
};
vicap_mipi2: port@3 {
@@ -1568,6 +1576,66 @@ vicap_mmu: iommu@fdce0800 {
status = "disabled";
};
+ csi0: csi@fdd10000 {
+ compatible = "rockchip,rk3588-mipi-csi2", "rockchip,rk3568-mipi-csi2";
+ reg = <0x0 0xfdd10000 0x0 0x10000>;
+ interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "err1", "err2";
+ clocks = <&cru PCLK_CSI_HOST_0>;
+ phys = <&mipidcphy0 PHY_DIRECTION_RX>;
+ power-domains = <&power RK3588_PD_VI>;
+ resets = <&cru SRST_P_CSI_HOST_0>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi0_in: port@0 {
+ reg = <0>;
+ };
+
+ csi0_out: port@1 {
+ reg = <1>;
+
+ csi0_output: endpoint {
+ remote-endpoint = <&vicap_mipi0_input>;
+ };
+ };
+ };
+ };
+
+ csi1: csi@fdd20000 {
+ compatible = "rockchip,rk3588-mipi-csi2", "rockchip,rk3568-mipi-csi2";
+ reg = <0x0 0xfdd20000 0x0 0x10000>;
+ interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "err1", "err2";
+ clocks = <&cru PCLK_CSI_HOST_1>;
+ phys = <&mipidcphy1 PHY_DIRECTION_RX>;
+ power-domains = <&power RK3588_PD_VI>;
+ resets = <&cru SRST_P_CSI_HOST_1>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ csi1_in: port@0 {
+ reg = <0>;
+ };
+
+ csi1_out: port@1 {
+ reg = <1>;
+
+ csi1_output: endpoint {
+ remote-endpoint = <&vicap_mipi1_input>;
+ };
+ };
+ };
+ };
+
csi2: csi@fdd30000 {
compatible = "rockchip,rk3588-mipi-csi2", "rockchip,rk3568-mipi-csi2";
reg = <0x0 0xfdd30000 0x0 0x10000>;
--
2.43.0