Re: [PATCH v7 0/8] arm64: dts: monaco-arduino-monza: Add support for LGA WiFi/BT module

From: Loic Poulain

Date: Mon Nov 16 2026 - 12:14:52 EST


Hi Luiz, Bartosz,

On Mon, Oct 5, 2026 at 2:21 PM Loic Poulain
<loic.poulain@xxxxxxxxxxxxxxxx> wrote:
>
> This series describes support for the onboard WiFi/Bluetooth module
> present on the Arduino VENTUNO Q (monaco) platform.
>
> The board provides LGA pads for a wireless module. On the VENTUNO Q
> these pads are populated with an NFA725B module featuring the
> QCA2066 WiFi/BT combo chip. While implemented as an LGA footprint,
> the design is functionally compatible with the M.2 Key E.
>
> The NFA725B exposes WiFi over PCIe and Bluetooth over a UART.
> Both interfaces are gated through the W_DISABLE1# and W_DISABLE2#
> signals, as defined by the M.2 specification and handled here via
> the pcie-m2 power sequencer.
>
> This series models the hardware using the existing pwrseq framework
> and connector bindings, allowing coordinated PCIe and UART bring-up.
>
> Signed-off-by: Loic Poulain <loic.poulain@xxxxxxxxxxxxxxxx>

Is there anything blocking this series from being picked up for
Bluetooth? I've already rebased it, so I'd appreciate any feedback if
anything still needs to be addressed.

Thanks,
Loic


> ---
> Changes in v7:
> - Rebased on linux-next (pwrseq changes dropped)
> - Link to v6: https://lore.kernel.org/r/20260904-monza-wireless-v6-0-d8c5042b3efd@xxxxxxxxxxxxxxxx
>
> Changes in v6:
> - Rebase onto v7.3-rc1: drop the now-upstream "power: sequencing: pcie-m2:
> Add QCA2066 (QCNFA765) BT serdev ID" patch and adapt to the
> pwrseq_power_on()/pwrseq_power_off() -> pwrseq_enable()/pwrseq_disable()
> rename that landed in this merge window.
> - hci_qca: fully drop struct qca_power and move its fields directly into
> struct qca_serdev, removing the bt_power indirection (Dmitry).
> - Pick up Reviewed-by/Acked-by tags from Mani, Bartosz and Dmitry on the
> pwrseq_is_controllable() API, the pcie-m2/qcom-wcn controllability
> reporting, the bt_en_available rework and the M.2 connector support
> patches.
> - Drop the pwrseq-m2-bt prerequisite series link, it is now merged upstream
> and included in the v7.3-rc1 base.
> - Link to v5: https://lore.kernel.org/r/20260720-monza-wireless-v5-0-69ec6743543c@xxxxxxxxxxxxxxxx
>
> Changes in v5:
> - hci_qca: comment why the M.2 'uart' pwrseq lifetime is bound to the serdev
> consumer device instead of using devm_pwrseq_get() on the controller (Bartosz).
> - hci_qca: note that dropping the always-on pwrseq handle is not a leak since
> the descriptor is still released by devres (Bartosz).
> - Link to v4: https://lore.kernel.org/r/20260716-monza-wireless-v4-0-9b02e6f549d7@xxxxxxxxxxxxxxxx
>
> Changes in v4:
> - pwrseq: rename pwrseq_power_is_controllable() to pwrseq_is_controllable() (Bartosz).
> - pwrseq: move the is_controllable() callback from the unit to the target (Bartosz).
> - pwrseq: add might_sleep() and guard pwrseq_is_controllable() against
> concurrent provider removal with rw_lock, matching pwrseq_power_on/off() (Bartosz).
> - pwrseq: clarify the pwrseq_is_controllable() doc (Bartosz)
> - hci_qca: lifetime follows the Bluetooth device rather than the UART controller (ChenYu).
> - dt-bindings: also add the "qcom,pcie-m2-1620-lga-connector" compatible (Mani).
> - arm64: dts: monaco-arduino-monza: rename the 'pcie_bridge_ep' endpoint to 'pcie_ep' (Mani).
> - pwrseq: reword commmit message (Mani)
> - Link to v3: https://lore.kernel.org/r/20260710-monza-wireless-v3-0-46253587af64@xxxxxxxxxxxxxxxx
>
> Changes in v3:
> - Embed bt_power in struct qca_serdev instead of allocating it (Dmitry).
> - Add generic pwrseq_is_controllable() API + per-target .is_controllable()
> callback; use it in hci_qca instead of peeking at the W_DISABLE2# property.
> - Implement .is_controllable() in the pcie-m2 and qcom-wcn providers.
> - Treat non-controllable BT power as always-on.
> - Integrate the pending Bluetooth pwrseq patches from Mani.
> - Link to v2: https://lore.kernel.org/r/20260702-monza-wireless-v2-0-7b56e2a6a6d4@xxxxxxxxxxxxxxxx
>
> Changes in v2:
> - hci_qca: extract M.2 pwrseq into qca_serdev_get_m2_pwrseq() helper, called
> outside the SoC switch; drop duplicated of_graph logic and redundant
> bt_power NULL checks (Dmitry/Mani)
> - dts/bindings: use qcom,pcie-m2-1418-lga-connector (fallback
> pcie-m2-e-connector) instead of the generic M.2 E-key compatible (Mani)
> - Link to v1: https://lore.kernel.org/r/20260520-monza-wireless-v1-0-9f6942310653@xxxxxxxxxxxxxxxx
>
> ---
> Loic Poulain (6):
> Bluetooth: hci_qca: Set 'bt_en_available' based on pwrseq power controllability
> Bluetooth: hci_qca: Embed bt_power in struct qca_serdev
> Bluetooth: hci_qca: Support QCA2066 on M.2 connector via pwrseq
> Bluetooth: hci_qca: Flatten struct qca_power into struct qca_serdev
> dt-bindings: connector: pcie-m2-e: Add vendor LGA connector compatible
> arm64: dts: qcom: monaco-arduino-monza: Add QCA2066 M.2 WiFi/BT support
>
> Manivannan Sadhasivam (2):
> Bluetooth: hci_qca: Add M.2 Bluetooth device support using pwrseq
> Bluetooth: hci_qca: Rename 'power_ctrl_enabled' to 'bt_en_available'
>
> .../bindings/connector/pcie-m2-e-connector.yaml | 8 +-
> arch/arm64/boot/dts/qcom/monaco-arduino-monza.dts | 64 ++++++++-
> drivers/bluetooth/hci_qca.c | 160 ++++++++++++---------
> 3 files changed, 157 insertions(+), 75 deletions(-)
> ---
> base-commit: f0406245cb9855e6318335a8a223551354291a46
> change-id: 20260520-monza-wireless-e6ce7f013f38
>
> Best regards,
> --
> Loic Poulain <loic.poulain@xxxxxxxxxxxxxxxx>
>