Re: [PATCH 5/6] media: qcom: camss: csid: Add support for CSID 1080
From: Hangxiang Ma
Date: Tue Oct 14 2025 - 23:44:12 EST
On 9/26/2025 7:30 AM, Bryan O'Donoghue wrote:
On 25/09/2025 01:02, Jingyi Wang wrote:
From: Hangxiang Ma <hangxiang.ma@xxxxxxxxxxxxxxxx>
Add more detailed resource information for CSID devices along with the
driver for CSID 1080 that is responsible for CSID register
configuration, module reset and IRQ handling for BUF_DONE events.
In this CSID version, RUP and AUP update values are split into two
registers along with a SET register. Accordingly , enhance the CSID
interface to accommodate both the legacy combined reg_update and the
split RUP and AUP updates.
Co-developed-by: Atiya Kailany <atiya.kailany@xxxxxxxxxxxxxxxx>
Signed-off-by: Atiya Kailany <atiya.kailany@xxxxxxxxxxxxxxxx>
Signed-off-by: Hangxiang Ma <hangxiang.ma@xxxxxxxxxxxxxxxx>
Signed-off-by: Jingyi Wang <jingyi.wang@xxxxxxxxxxxxxxxx>
---
drivers/media/platform/qcom/camss/Makefile | 1 +
.../media/platform/qcom/camss/camss-csid-1080.c | 379 +++++++++++++++++++++
.../media/platform/qcom/camss/camss-csid-1080.h | 25 ++
drivers/media/platform/qcom/camss/camss-csid.h | 9 +-
drivers/media/platform/qcom/camss/camss.c | 80 +++++
drivers/media/platform/qcom/camss/camss.h | 1 +
6 files changed, 494 insertions(+), 1 deletion(-)
diff --git a/drivers/media/platform/qcom/camss/Makefile b/drivers/media/platform/qcom/camss/Makefile
index 23960d02877d..3a7ed4f5a004 100644
--- a/drivers/media/platform/qcom/camss/Makefile
+++ b/drivers/media/platform/qcom/camss/Makefile
@@ -8,6 +8,7 @@ qcom-camss-objs += \
camss-csid-4-7.o \
camss-csid-340.o \
camss-csid-680.o \
+ camss-csid-1080.o \
camss-csid-gen2.o \
camss-csid-gen3.o \
camss-csiphy-2ph-1-0.o \
diff --git a/drivers/media/platform/qcom/camss/camss-csid-1080.c b/drivers/media/platform/qcom/camss/camss-csid-1080.c
new file mode 100644
index 000000000000..ab5944d4ff34
--- /dev/null
+++ b/drivers/media/platform/qcom/camss/camss-csid-1080.c
@@ -0,0 +1,379 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * camss-csid-1080.c
+ *
+ * Qualcomm MSM Camera Subsystem - CSID (CSI Decoder) Module
+ *
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/of.h>
+#include <linux/types.h>
+#include <linux/v4l2-controls.h>
+#include "camss.h"
+#include "camss-csid.h"
+#include "camss-csid-1080.h"
+
+/* Reset and Command Registers */
+#define CSID_RST_CFG 0x108
+#define RST_MODE BIT(0)
+#define RST_LOCATION BIT(4)
+
+/* Reset and Command Registers */
+#define CSID_RST_CMD 0x10C
+#define SELECT_HW_RST BIT(0)
+#define SELECT_IRQ_RST BIT(2)
+#define CSID_IRQ_CMD 0x110
+#define IRQ_CMD_CLEAR BIT(0)
+
+/* Register Update Commands, RUP/AUP */
+#define CSID_RUP_CMD 0x114
+#define RUP_RDIN BIT(8)
+#define CSID_AUP_CMD 0x118
+#define AUP_RDIN BIT(8)
+#define CSID_RUP_AUP_CMD 0x11C
+#define RUP_SET BIT(0)
+#define MUP BIT(4)
+
+/* Top level interrupt registers */
+#define CSID_TOP_IRQ_STATUS 0x180
+#define CSID_TOP_IRQ_MASK 0x184
+#define CSID_TOP_IRQ_CLEAR 0x188
+#define CSID_TOP_IRQ_SET 0x18C
+#define INFO_RST_DONE BIT(0)
+#define CSI2_RX_IRQ_STATUS BIT(2)
+#define BUF_DONE_IRQ_STATUS BIT(3)
+#define RDIn_IRQ_STATUS_OFFSET 16
+#define TOP_IRQ_STATUS_2 BIT(31)
+
+/* Buffer done interrupt registers */
+#define CSID_BUF_DONE_IRQ_STATUS 0x1A0
+#define BUF_DONE_IRQ_STATUS_RDI_OFFSET 16
+#define CSID_BUF_DONE_IRQ_MASK 0x1A4
+#define CSID_BUF_DONE_IRQ_CLEAR 0x1A8
+#define CSID_BUF_DONE_IRQ_SET 0x1AC
+
+/* CSI2 RX interrupt registers */
+#define CSID_CSI2_RX_IRQ_STATUS 0x1B0
+#define CSID_CSI2_RX_IRQ_MASK 0x1B4
+#define CSID_CSI2_RX_IRQ_CLEAR 0x1B8
+#define CSID_CSI2_RX_IRQ_SET 0x1BC
+
+/* CSI2 RX Configuration */
+#define CSID_CSI2_RX_CFG0 0x880
+#define CSI2_RX_CFG0_NUM_ACTIVE_LANES 0
+#define CSI2_RX_CFG0_DL0_INPUT_SEL 4
+#define CSI2_RX_CFG0_PHY_NUM_SEL 20
+#define CSID_CSI2_RX_CFG1 0x884
+#define CSI2_RX_CFG1_ECC_CORRECTION_EN BIT(0)
+#define CSI2_RX_CFG1_VC_MODE BIT(2)
+
+/* CSIPHY to hardware PHY selector mapping */
+#define CSID_CSIPHY_ID_BASE_OFFSET 1
Please align to the existing namespace and now that I look at it, try to aggregate some of these defines into one place.
Its a bit mindless repeating defines/code in silos within the same driver.
e.g.
grep -r -e CSID_CSIPHY_ID_BASE_OFFSET -e CSI2_RX_CFG0_PHY_SEL_BASE_IDX drivers/media/platform/qcom/camss/*
drivers/media/platform/qcom/camss/camss-csid-1080.c:#define CSID_CSIPHY_ID_BASE_OFFSET 1
drivers/media/platform/qcom/camss/camss-csid-1080.c: val |= (phy->csiphy_id + CSID_CSIPHY_ID_BASE_OFFSET)
drivers/media/platform/qcom/camss/camss-csid-680.c:#define CSI2_RX_CFG0_PHY_SEL_BASE_IDX 1
drivers/media/platform/qcom/camss/camss-csid-680.c: val |= (phy->csiphy_id + CSI2_RX_CFG0_PHY_SEL_BASE_IDX) << CSI2_RX_CFG0_PHY_NUM_SEL;
drivers/media/platform/qcom/camss/camss-csid-gen3.c:#define CSI2_RX_CFG0_PHY_SEL_BASE_IDX 1
drivers/media/platform/qcom/camss/camss-csid-gen3.c: val |= (phy->csiphy_id + CSI2_RX_CFG0_PHY_SEL_BASE_IDX) << CSI2_RX_CFG0_PHY_NUM_SEL;
Expectation for v2 here is to review defines ensure the names are consistent with what's upstream and where possible moving common defines into one header.
> +
Ack
Thanks. Will keep it.+#define MSM_CSID_MAX_SRC_STREAMS_1080 (csid_is_lite(csid) ? 4 : 5)
+
+/* RDI Configuration */
+#define CSID_RDI_CFG0(rdi) \
+ ((csid_is_lite(csid) ? 0x3080 : 0x5480) + 0x200 * (rdi))
+#define RDI_CFG0_RETIME_BS BIT(5)
+#define RDI_CFG0_TIMESTAMP_EN BIT(6)
+#define RDI_CFG0_TIMESTAMP_STB_SEL BIT(8)
+#define RDI_CFG0_DECODE_FORMAT 12
+#define RDI_CFG0_DT 16
+#define RDI_CFG0_VC 22
+#define RDI_CFG0_EN BIT(31)
+
+/* RDI Control and Configuration */
+#define CSID_RDI_CTRL(rdi) \
+ ((csid_is_lite(csid) ? 0x3088 : 0x5488) + 0x200 * (rdi))
+#define RDI_CTRL_START_CMD BIT(0)
+
+#define CSID_RDI_CFG1(rdi) \
+ ((csid_is_lite(csid) ? 0x3094 : 0x5494) + 0x200 * (rdi))
+#define RDI_CFG1_DROP_H_EN BIT(5)
+#define RDI_CFG1_DROP_V_EN BIT(6)
+#define RDI_CFG1_CROP_H_EN BIT(7)
+#define RDI_CFG1_CROP_V_EN BIT(8)
+#define RDI_CFG1_PACKING_FORMAT_MIPI BIT(15)
+
+/* RDI Pixel Store Configuration */
+#define CSID_RDI_PIX_STORE_CFG0(rdi) (0x5498 + 0x200 * (rdi))
+#define RDI_PIX_STORE_CFG0_EN BIT(0)
+#define RDI_PIX_STORE_CFG0_MIN_HBI 1
+
+/* RDI IRQ Status in wrapper */
+#define CSID_RDIN_IRQ_STATUS(rdi) (0x224 + (0x10 * (rdi)))
+#define CSID_RDIN_IRQ_MASK(rdi) (0x228 + (0x10 * (rdi)))
+#define CSID_RDIN_IRQ_CLEAR(rdi) (0x22C + (0x10 * (rdi)))
+#define INFO_RUP_DONE BIT(23)
+
+static void __csid_aup_rup_trigger(struct csid_device *csid)
+{
+ /* trigger SET in combined register */
+ writel(RUP_SET, csid->base + CSID_RUP_AUP_CMD);
+}
+
+static void __csid_aup_update(struct csid_device *csid, int port_id)
+{
+ csid->aup_update |= AUP_RDIN << port_id;
+ writel(csid->aup_update, csid->base + CSID_AUP_CMD);
+
+ __csid_aup_rup_trigger(csid);
+}
+
+static void __csid_reg_update(struct csid_device *csid, int port_id)
+{
+ csid->rup_update |= RUP_RDIN << port_id;
+ writel(csid->rup_update, csid->base + CSID_RUP_CMD);
+
+ __csid_aup_rup_trigger(csid);
+}
+
+static void __csid_configure_rx(struct csid_device *csid,
+ struct csid_phy_config *phy)
+{
+ int val;
+
+ val = (phy->lane_cnt - 1) << CSI2_RX_CFG0_NUM_ACTIVE_LANES;
+ val |= phy->lane_assign << CSI2_RX_CFG0_DL0_INPUT_SEL;
+ val |= (phy->csiphy_id + CSID_CSIPHY_ID_BASE_OFFSET)
+ << CSI2_RX_CFG0_PHY_NUM_SEL;
+ writel(val, csid->base + CSID_CSI2_RX_CFG0);
+
+ val = CSI2_RX_CFG1_ECC_CORRECTION_EN;
+ writel(val, csid->base + CSID_CSI2_RX_CFG1);
+}
+
+static void __csid_configure_rx_vc(struct csid_device *csid,
+ struct csid_phy_config *phy, int vc)
+{
+ int val;
+
+ if (vc > 3) {
+ val = readl(csid->base + CSID_CSI2_RX_CFG1);
+ val |= CSI2_RX_CFG1_VC_MODE;
+ writel(val, csid->base + CSID_CSI2_RX_CFG1);
+ }
+}
+
+static void __csid_ctrl_rdi(struct csid_device *csid, int enable, u8 rdi)
+{
+ int val = 0;
+
+ if (enable)
+ val = RDI_CTRL_START_CMD;
+
+ writel(val, csid->base + CSID_RDI_CTRL(rdi));
+}
+
+static void __csid_configure_rdi_pix_store(struct csid_device *csid, u8 rdi)
+{
+ u32 val;
+
+ /* Configure pixel store to allow absorption of hblanking or idle time.
+ * This helps with horizontal crop and prevents line buffer conflicts.
+ * Reset state is 0x8 which has MIN_HBI=4, we keep the default MIN_HBI
+ * and just enable the pixel store functionality.
+ */
+ val = (4 << RDI_PIX_STORE_CFG0_MIN_HBI) | RDI_PIX_STORE_CFG0_EN;
+ writel(val, csid->base + CSID_RDI_PIX_STORE_CFG0(rdi));
+}
+
+static void __csid_configure_rdi_stream(struct csid_device *csid, u8 enable, u8 vc)
+{
+ u32 val;
+ u8 lane_cnt = csid->phy.lane_cnt;
+
+ /* Source pads matching RDI channels on hardware.
+ * E.g. Pad 1 -> RDI0, Pad 2 -> RDI1, etc.
+ */
+ struct v4l2_mbus_framefmt *input_format = &csid->fmt[MSM_CSID_PAD_FIRST_SRC + vc];
+ const struct csid_format_info *format = csid_get_fmt_entry(csid->res->formats->formats,
+ csid->res->formats->nformats,
+ input_format->code);
+
+ if (!lane_cnt)
+ lane_cnt = 4;
+
+ val = RDI_CFG0_TIMESTAMP_EN;
+ val |= RDI_CFG0_TIMESTAMP_STB_SEL;
+ val |= RDI_CFG0_RETIME_BS;
+
+ /* note: for non-RDI path, this should be format->decode_format */
+ val |= DECODE_FORMAT_PAYLOAD_ONLY << RDI_CFG0_DECODE_FORMAT;
+ val |= vc << RDI_CFG0_VC;
+ val |= format->data_type << RDI_CFG0_DT;
+ writel(val, csid->base + CSID_RDI_CFG0(vc));
+
+ val = RDI_CFG1_PACKING_FORMAT_MIPI;
+ writel(val, csid->base + CSID_RDI_CFG1(vc));
+
+ /* Configure pixel store using dedicated register in 1080 */
+ if (!csid_is_lite(csid))
+ __csid_configure_rdi_pix_store(csid, vc);
+
+ val = 0;
+ writel(val, csid->base + CSID_RDI_CTRL(vc));
+
+ val = readl(csid->base + CSID_RDI_CFG0(vc));
+
+ if (enable)
+ val |= RDI_CFG0_EN;
+
+ writel(val, csid->base + CSID_RDI_CFG0(vc));
+}
+
+static void csid_configure_stream_1080(struct csid_device *csid, u8 enable)
+{
+ u8 i;
+ u8 vc;
+
+ __csid_configure_rx(csid, &csid->phy);
+
+ for (vc = 0; vc < MSM_CSID_MAX_SRC_STREAMS_1080; vc++) {
+ if (csid->phy.en_vc & BIT(vc)) {
+ __csid_configure_rdi_stream(csid, enable, vc);
+ __csid_configure_rx_vc(csid, &csid->phy, vc);
+
+ for (i = 0; i < CAMSS_INIT_BUF_COUNT; i++)
+ __csid_aup_update(csid, vc);
+
+ __csid_reg_update(csid, vc);
+
+ __csid_ctrl_rdi(csid, enable, vc);
+ }
+ }
+}
+
+static int csid_configure_testgen_pattern_1080(struct csid_device *csid,
+ s32 val)
+{
+ return 0;
+}
+
+static void csid_subdev_reg_update_1080(struct csid_device *csid, int port_id,
+ bool clear)
+{
+ /* No explicit clear required */
+ if (!clear)
+ __csid_aup_update(csid, port_id);
+}
+
+/**
+ * csid_isr - CSID module interrupt service routine
+ * @irq: Interrupt line
+ * @dev: CSID device
+ *
+ * Return IRQ_HANDLED on success
+ */
+static irqreturn_t csid_isr_1080(int irq, void *dev)
+{
+ struct csid_device *csid = dev;
+ u32 val, buf_done_val;
+ u8 reset_done;
+ int i;
+
+ val = readl(csid->base + CSID_TOP_IRQ_STATUS);
+ writel(val, csid->base + CSID_TOP_IRQ_CLEAR);
+
+ reset_done = val & INFO_RST_DONE;
+
+ buf_done_val = readl(csid->base + CSID_BUF_DONE_IRQ_STATUS);
+ writel(buf_done_val, csid->base + CSID_BUF_DONE_IRQ_CLEAR);
+
+ for (i = 0; i < MSM_CSID_MAX_SRC_STREAMS_1080; i++)
+ if (csid->phy.en_vc & BIT(i)) {
+ val = readl(csid->base + CSID_RDIN_IRQ_STATUS(i));
+ writel(val, csid->base + CSID_RDIN_IRQ_CLEAR(i));
+
+ if (buf_done_val & BIT(BUF_DONE_IRQ_STATUS_RDI_OFFSET + i)) {
+ /*
+ * buf done and RUP IRQ have been moved to CSID from VFE.
+ * Once CSID received buf done, need notify VFE of this
+ * event and trigger VFE to handle buf done process.
+ */
+ camss_buf_done(csid->camss, csid->id, i);
+ }
+ }
+
+ val = IRQ_CMD_CLEAR;
+ writel(val, csid->base + CSID_IRQ_CMD);
+
+ if (reset_done)
+ complete(&csid->reset_complete);
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * csid_reset - Trigger reset on CSID module and wait to complete
+ * @csid: CSID device
+ *
+ * Return 0 on success or a negative error code otherwise
+ */
+static int csid_reset_1080(struct csid_device *csid)
+{
+ unsigned long time;
+ u32 val;
+ int i;
+
+ reinit_completion(&csid->reset_complete);
+
+ val = INFO_RST_DONE | BUF_DONE_IRQ_STATUS;
+ writel(val, csid->base + CSID_TOP_IRQ_CLEAR);
+ writel(val, csid->base + CSID_TOP_IRQ_MASK);
+
+ val = 0;
+ for (i = 0; i < MSM_CSID_MAX_SRC_STREAMS_1080; i++) {
+ if (csid->phy.en_vc & BIT(i)) {
+ /* only need to clear Buffer Done IRQ Status here,
+ * RUP Done IRQ Status will be cleared once isr
+ * strobe generated by CSID_RST_CMD
+ */
I like this self-documenting code BTW, thanks for the commentary effort.
This is not required for Apollo architecture and that there is no CSID_SWAPPER_TOP register space.+ val |= BIT(BUF_DONE_IRQ_STATUS_RDI_OFFSET + i);
+ }
+ }
+ writel(val, csid->base + CSID_BUF_DONE_IRQ_CLEAR);
+ writel(val, csid->base + CSID_BUF_DONE_IRQ_MASK);
+
+ /* Clear all IRQ status with CLEAR bits set */
+ val = IRQ_CMD_CLEAR;
+ writel(val, csid->base + CSID_IRQ_CMD);
+
+ val = RST_LOCATION | RST_MODE;
+ writel(val, csid->base + CSID_RST_CFG);
+
+ val = SELECT_HW_RST | SELECT_IRQ_RST;
+ writel(val, csid->base + CSID_RST_CMD);
+
+ time = wait_for_completion_timeout(&csid->reset_complete,
+ msecs_to_jiffies(CSID_RESET_TIMEOUT_MS));
+
+ if (!time) {
+ dev_err(csid->camss->dev, "CSID reset timeout\n");
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static void csid_subdev_init_1080(struct csid_device *csid)
+{
+ csid->testgen.nmodes = CSID_PAYLOAD_MODE_DISABLED;
+}
+
+const struct csid_hw_ops csid_ops_1080 = {
+ .configure_stream = csid_configure_stream_1080,
+ .configure_testgen_pattern = csid_configure_testgen_pattern_1080,
+ .hw_version = csid_hw_version,
+ .isr = csid_isr_1080,
+ .reset = csid_reset_1080,
+ .src_pad_code = csid_src_pad_code,
+ .subdev_init = csid_subdev_init_1080,
+ .reg_update = csid_subdev_reg_update_1080,
+};
Awaiting access to the register list for this part however, where is
__csid_configure_wrapper(struct csid_device *csid){}
Is this mux not required on your hardware ?
Ackdiff --git a/drivers/media/platform/qcom/camss/camss-csid-1080.h b/drivers/media/platform/qcom/camss/camss-csid-1080.h
new file mode 100644
index 000000000000..f526f3168e33
--- /dev/null
+++ b/drivers/media/platform/qcom/camss/camss-csid-1080.h
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * camss-csid-1080.h
+ *
+ * Qualcomm MSM Camera Subsystem - CSID (CSI Decoder) Module Generation 3
+ *
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+#ifndef __QC_MSM_CAMSS_CSID_1080_H__
+#define __QC_MSM_CAMSS_CSID_1080_H__
+
+#define DECODE_FORMAT_UNCOMPRESSED_8_BIT 0x1
+#define DECODE_FORMAT_UNCOMPRESSED_10_BIT 0x2
+#define DECODE_FORMAT_UNCOMPRESSED_12_BIT 0x3
+#define DECODE_FORMAT_UNCOMPRESSED_14_BIT 0x4
+#define DECODE_FORMAT_UNCOMPRESSED_16_BIT 0x5
+#define DECODE_FORMAT_UNCOMPRESSED_20_BIT 0x6
+#define DECODE_FORMAT_UNCOMPRESSED_24_BIT 0x7
+#define DECODE_FORMAT_PAYLOAD_ONLY 0xf
+
+#define PLAIN_FORMAT_PLAIN8 0x0 /* supports DPCM, UNCOMPRESSED_6/8_BIT */
+#define PLAIN_FORMAT_PLAIN16 0x1 /* supports DPCM, UNCOMPRESSED_10/16_BIT */
+#define PLAIN_FORMAT_PLAIN32 0x2 /* supports UNCOMPRESSED_20_BIT */
+
+#endif /* __QC_MSM_CAMSS_CSID_1080_H__ */
This header is a 1:1 drivers/media/platform/qcom/camss/camss-csid-gen3.h of its completely redundant.
Please go through your submission and rationalise the copy/pasting.