Re: [PATCH 3/3] arm64: dts: rockchip: Add RTL8367RB-VB switch to Radxa E24C

[Chukun Pan]

Hi,

> Initial testing with iperf3 showed ~930-940 Mbits/sec in one direction
> and only around ~1-2 Mbits/sec in the other direction.

> Any mix of MAC (rx/tx delay) and switch (rx/tx internal delay) did not
> seem to resolve this speed issue, however dropping snps,tso seems to fix
> that issue.

Have you tried setting phy-mode to rgmii? (just for testing)
Usually this problem is caused by incorrect rx/tx delay.

> +	ethernet-switch@1d {
> +		compatible = "realtek,rtl8365mb";
> +		reg = <0x1d>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&rtl8367rb_eint>;

Shouldn't this pinctrl be written in interrupts?

> +			ethernet-port@6 {
> +				reg = <6>;
> +				ethernet = <&gmac1>;
> +				label = "cpu";

No need for label = "cpu":
https://github.com/torvalds/linux/commit/567f38317054e66647fd59cfa4e261219a2a21db

> This series relaxes the realtek dsa drivers requirement of having a mdio
> child OF node to probe and instead have it register a user_mii_bus to
> make it function when a mdio child OF node is missing.

This is weird, the switch is connected to the gmac via mdio.
Can you try the following and see if it works? I tried it on
a rk3568 + rtl8367s board and it worked:

```
&mdio1 {
	switch@29 {
		compatible = "realtek,rtl8365mb";
		reg = <29>;
		reset-gpios = ...

		switch_intc: interrupt-controller {
			interrupt-parent = ...
			interrupts = ...
			interrupt-controller;
			#address-cells = <0>;
			#interrupt-cells = <1>;
		};

		mdio {
			#address-cells = <1>;
			#size-cells = <0>;

			phy0: ethernet-phy@0 {
				reg = <0>;
				interrupt-parent = <&switch_intc>;
				interrupts = <0>;
			};

			phy1: ethernet-phy@1 {
				reg = <1>;
				interrupt-parent = <&switch_intc>;
				interrupts = <1>;
			};

			phy2: ethernet-phy@2 {
				reg = <2>;
				interrupt-parent = <&switch_intc>;
				interrupts = <2>;
			};

			phy3: ethernet-phy@3 {
				reg = <3>;
				interrupt-parent = <&switch_intc>;
				interrupts = <3>;
			};
		};

		ports {
			#address-cells = <1>;
			#size-cells = <0>;

			port@0 {
				reg = <0>;
				label = "wan";
				phy-handle = <&phy0>;
			};

			port@1 {
				reg = <1>;
				label = "lan1";
				phy-handle = <&phy1>;
			};

			port@2 {
				reg = <2>;
				label = "lan2";
				phy-handle = <&phy2>;
			};

			port@3 {
				reg = <3>;
				label = "lan3";
				phy-handle = <&phy3>;
			};

			port@x {
				reg = <x>;
				ethernet = <&gmac1>;
				phy-mode = "rgmii";

				fixed-link {
					speed = <1000>;
					full-duplex;
				};
			};
		};
	};
};
```

Thanks,
Chukun

--
2.25.1