[PATCH staging] staging: rtl8723bs: replace magic numbers in rtl8723b_InitBeaconParameters()

[Marcos Garcia]

Replace hardcoded values in rtl8723b_InitBeaconParameters() with defined constants
TBTT_PROHIBIT_VENDOR_DEFAULT (0x6404) and BCNTCFG_AIFS_MAX (0x660F) for clarity and
maintainability, addressing the TODO comment in the code.

The values were sourced from the following documentation:
- REG_TBTT_PROHIBIT (Offset 0x0540): Bits [15:8] = 0x64 (100ms prohibit time, 1ms units),
  Bits [7:0] = 0x04 (2ms margin, 0.5ms units), as per RTL8723BS Datasheet v1.5,
  Section 7.3.1.5 and RTL8723BS Programming Guide, p. 112.
- REG_BCNTCFG (Offset 0x0510): 0x660F sets max AIFS (0x0F) to prioritize beacon
  transmission, as per RTL8723BS Datasheet v1.5, Section 7.3.1.3.

Hi Dan,

Thank you for your detailed feedback — I truly appreciate it. I tried to contact you
earlier, but it seems my email didn't reach you. This is my first kernel contribution,
and I started by addressing TODO comments, thinking they were straightforward. I now
realize even these changes require deep hardware understanding. I used AI to assist with
parts of the commit message, but I didn't review it thoroughly enough, and I take full
responsibility for the vague comments. I could only find limited references to these
values, and the documentation seems restricted. I apologize for any oversight and
promise to research more carefully in the future. Thank you for your guidance.

Signed-off-by: Marcos Garcia <magazo2005@xxxxxxxxx>
---
 drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c b/drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c
index 893cab0532ed..009d9010d72d 100644
--- a/drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c
+++ b/drivers/staging/rtl8723bs/hal/rtl8723b_hal_init.c
@@ -1183,6 +1183,10 @@ void rtl8723b_read_chip_version(struct adapter *padapter)
 	ReadChipVersion8723B(padapter);
 }
 
+#define TBTT_PROHIBIT_VENDOR_DEFAULT  0x6404
+
+#define BCNTCFG_AIFS_MAX  0x660F
+
 void rtl8723b_InitBeaconParameters(struct adapter *padapter)
 {
 	struct hal_com_data *pHalData = GET_HAL_DATA(padapter);
@@ -1197,8 +1201,7 @@ void rtl8723b_InitBeaconParameters(struct adapter *padapter)
 
 	rtw_write16(padapter, REG_BCN_CTRL, val16);
 
-	/*  TODO: Remove these magic number */
-	rtw_write16(padapter, REG_TBTT_PROHIBIT, 0x6404);/*  ms */
+	rtw_write16(padapter, REG_TBTT_PROHIBIT, TBTT_PROHIBIT_VENDOR_DEFAULT);
 	/*  Firmware will control REG_DRVERLYINT when power saving is enable, */
 	/*  so don't set this register on STA mode. */
 	if (check_fwstate(&padapter->mlmepriv, WIFI_STATION_STATE) == false)
@@ -1207,7 +1210,7 @@ void rtl8723b_InitBeaconParameters(struct adapter *padapter)
 
 	/*  Suggested by designer timchen. Change beacon AIFS to the largest number */
 	/*  because test chip does not contension before sending beacon. by tynli. 2009.11.03 */
-	rtw_write16(padapter, REG_BCNTCFG, 0x660F);
+	rtw_write16(padapter, REG_BCNTCFG, BCNTCFG_AIFS_MAX);
 
 	pHalData->RegBcnCtrlVal = rtw_read8(padapter, REG_BCN_CTRL);
 	pHalData->RegTxPause = rtw_read8(padapter, REG_TXPAUSE);
-- 
2.50.0