Re: [PATCH v5 5/5] arm64: dts: qcom: qcm2290: Add venus video node

[Jorge Ramirez]

On 27/06/25 17:40:19, Vikash Garodia wrote:
> 
> On 6/26/2025 7:29 PM, Jorge Ramirez-Ortiz wrote:
> > Add DT entries for the qcm2290 venus encoder/decoder.
> > 
> > Co-developed-by: Loic Poulain <loic.poulain@xxxxxxxxxxxxxxxx>
> > Signed-off-by: Loic Poulain <loic.poulain@xxxxxxxxxxxxxxxx>
> > Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez@xxxxxxxxxxxxxxxx>
> > ---
> >  arch/arm64/boot/dts/qcom/qcm2290.dtsi | 57 +++++++++++++++++++++++++++
> >  1 file changed, 57 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/qcm2290.dtsi b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
> > index f49ac1c1f8a3..5326c91a0ff0 100644
> > --- a/arch/arm64/boot/dts/qcom/qcm2290.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/qcm2290.dtsi
> > @@ -1628,6 +1628,63 @@ adreno_smmu: iommu@59a0000 {
> >  			#iommu-cells = <2>;
> >  		};
> >  
> > +		venus: video-codec@5a00000 {
> > +			compatible = "qcom,qcm2290-venus";
> > +			reg = <0 0x5a00000 0 0xf0000>;
> > +			interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
> > +
> > +			power-domains = <&gcc GCC_VENUS_GDSC>,
> > +					<&gcc GCC_VCODEC0_GDSC>,
> > +					<&rpmpd QCM2290_VDDCX>;
> > +			power-domain-names = "venus",
> > +					     "vcodec0",
> > +					     "cx";
> > +			operating-points-v2 = <&venus_opp_table>;
> > +
> > +			clocks = <&gcc GCC_VIDEO_VENUS_CTL_CLK>,
> > +				 <&gcc GCC_VIDEO_AHB_CLK>,
> > +				 <&gcc GCC_VENUS_CTL_AXI_CLK>,
> > +				 <&gcc GCC_VIDEO_THROTTLE_CORE_CLK>,
> > +				 <&gcc GCC_VIDEO_VCODEC0_SYS_CLK>,
> > +				 <&gcc GCC_VCODEC0_AXI_CLK>;
> > +			clock-names = "core",
> > +				      "iface",
> > +				      "bus",
> > +				      "throttle",
> > +				      "vcodec0_core",
> > +				      "vcodec0_bus";
> > +
> > +			memory-region = <&pil_video_mem>;
> > +			iommus = <&apps_smmu 0x860 0x0>,
> > +				 <&apps_smmu 0x880 0x0>,
> > +				 <&apps_smmu 0x861 0x04>,
> > +				 <&apps_smmu 0x863 0x0>,
> > +				 <&apps_smmu 0x804 0xe0>;
> keep only the non secure ones.

ok

> > +
> > +			interconnects = <&mmnrt_virt MASTER_VIDEO_P0 RPM_ALWAYS_TAG
> > +					 &bimc SLAVE_EBI1 RPM_ALWAYS_TAG>,
> > +					<&bimc MASTER_APPSS_PROC RPM_ACTIVE_TAG
> > +					 &config_noc SLAVE_VENUS_CFG RPM_ACTIVE_TAG>;
> > +			interconnect-names = "video-mem",
> > +					     "cpu-cfg";
> > +
> > +			status = "okay";
> > +
> > +			venus_opp_table: opp-table {
> > +				compatible = "operating-points-v2";
> > +
> > +				opp-133000000 {
> > +					opp-hz = /bits/ 64 <133000000>;
> > +					required-opps = <&rpmpd_opp_low_svs>;
> > +				};
> Fix the corner freq value

can you add some reference please?

I took this data from an internal document - not sure why the downstream
driver supports different values or where those were taken from (AFAIK
they are not supported)


> 
> Regards,
> Vikash
> > +
> > +				opp-240000000 {
> > +					opp-hz = /bits/ 64 <240000000>;
> > +					required-opps = <&rpmpd_opp_svs>;
> > +				};
> > +			};
> > +		};
> > +
> >  		mdss: display-subsystem@5e00000 {
> >  			compatible = "qcom,qcm2290-mdss";
> >  			reg = <0x0 0x05e00000 0x0 0x1000>;