Re: [PATCH v3 1/5 RESEND] thermal: qcom-spmi-temp-alarm: enable stage 2 shutdown when required

[Daniel Lezcano]

On Thu, Mar 20, 2025 at 01:24:04PM -0700, Anjelique Melendez wrote:
> From: David Collins <david.collins@xxxxxxxxxxxxxxxx>
> 
> Certain TEMP_ALARM GEN2 PMIC peripherals need over-temperature
> stage 2 automatic PMIC partial shutdown to be enabled in order to
> avoid repeated faults in the event of reaching over-temperature
> stage 3.  Modify the stage 2 shutdown control logic to ensure that
> stage 2 shutdown is enabled on all affected PMICs.  Read the
> digital major and minor revision registers to identify these
> PMICs.
> 
> Signed-off-by: David Collins <david.collins@xxxxxxxxxxxxxxxx>
> Signed-off-by: Anjelique Melendez <anjelique.melendez@xxxxxxxxxxxxxxxx>
> ---
>  drivers/thermal/qcom/qcom-spmi-temp-alarm.c | 32 +++++++++++++++++++--
>  1 file changed, 30 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
> index c2d59cbfaea9..b2077ff9fe73 100644
> --- a/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
> +++ b/drivers/thermal/qcom/qcom-spmi-temp-alarm.c
> @@ -1,6 +1,7 @@
>  // SPDX-License-Identifier: GPL-2.0-only
>  /*
>   * Copyright (c) 2011-2015, 2017, 2020, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
>   */
>  
>  #include <linux/bitops.h>
> @@ -16,6 +17,7 @@
>  
>  #include "../thermal_hwmon.h"
>  
> +#define QPNP_TM_REG_DIG_MINOR		0x00
>  #define QPNP_TM_REG_DIG_MAJOR		0x01
>  #define QPNP_TM_REG_TYPE		0x04
>  #define QPNP_TM_REG_SUBTYPE		0x05
> @@ -71,6 +73,7 @@ struct qpnp_tm_chip {
>  	struct device			*dev;
>  	struct thermal_zone_device	*tz_dev;
>  	unsigned int			subtype;
> +	unsigned int			dig_revision;
>  	long				temp;
>  	unsigned int			thresh;
>  	unsigned int			stage;
> @@ -78,6 +81,7 @@ struct qpnp_tm_chip {
>  	/* protects .thresh, .stage and chip registers */
>  	struct mutex			lock;
>  	bool				initialized;
> +	bool				require_s2_shutdown;
>  
>  	struct iio_channel		*adc;
>  	const long			(*temp_map)[THRESH_COUNT][STAGE_COUNT];
> @@ -255,7 +259,7 @@ static int qpnp_tm_update_critical_trip_temp(struct qpnp_tm_chip *chip,
>  
>  skip:
>  	reg |= chip->thresh;
> -	if (disable_s2_shutdown)
> +	if (disable_s2_shutdown && !chip->require_s2_shutdown)
>  		reg |= SHUTDOWN_CTRL1_OVERRIDE_S2;
>  
>  	return qpnp_tm_write(chip, QPNP_TM_REG_SHUTDOWN_CTRL1, reg);
> @@ -350,7 +354,7 @@ static int qpnp_tm_probe(struct platform_device *pdev)
>  {
>  	struct qpnp_tm_chip *chip;
>  	struct device_node *node;
> -	u8 type, subtype, dig_major;
> +	u8 type, subtype, dig_major, dig_minor;
>  	u32 res;
>  	int ret, irq;
>  
> @@ -403,6 +407,30 @@ static int qpnp_tm_probe(struct platform_device *pdev)
>  		return dev_err_probe(&pdev->dev, ret,
>  				     "could not read dig_major\n");
>  
> +	ret = qpnp_tm_read(chip, QPNP_TM_REG_DIG_MINOR, &dig_minor);
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "could not read dig_minor\n");
> +		return ret;
> +	}
> +
> +	chip->dig_revision = (dig_major << 8) | dig_minor;

I would move this inside the block below.

> +	if (chip->subtype == QPNP_TM_SUBTYPE_GEN2) {
> +		/*
> +		 * Check if stage 2 automatic partial shutdown must remain
> +		 * enabled to avoid potential repeated faults upon reaching
> +		 * over-temperature stage 3.
> +		 */
> +		switch (chip->dig_revision) {
> +		case 0x0001:
> +		case 0x0002:
> +		case 0x0100:
> +		case 0x0101:
> +			chip->require_s2_shutdown = true;
> +			break;
> +		}
> +	}

And move this block after the test below

> +
>  	if (type != QPNP_TM_TYPE || (subtype != QPNP_TM_SUBTYPE_GEN1
>  				     && subtype != QPNP_TM_SUBTYPE_GEN2)) {
>  		dev_err(&pdev->dev, "invalid type 0x%02x or subtype 0x%02x\n",
> -- 
> 2.34.1
> 

-- 

 <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog