Re: [PATCH V3 net 1/7] net: hns3: using user configure after hardware reset

From: Przemek Kitszel
Date: Tue May 07 2024 - 11:20:37 EST


On 5/7/24 15:42, Jijie Shao wrote:
From: Peiyang Wang <wangpeiyang1@xxxxxxxxxx>

When a reset occurring, it's supposed to recover user's configuration.
Currently, the port info(speed, duplex and autoneg) is stored in hclge_mac
and will be scheduled updated. Consider the case that reset was happened
consecutively. During the first reset, the port info is configured with
a temporary value cause the PHY is reset and looking for best link config.
Second reset start and use pervious configuration which is not the user's.

nit: for future submissions please run your commit messages through
spellchecker

The specific process is as follows:

+------+ +----+ +----+
| USER | | PF | | HW |
+---+--+ +-+--+ +-+--+
| ethtool --reset | |
+------------------->| reset command |
| ethtool --reset +-------------------->|
+------------------->| +---+
| +---+ | |
| | |reset currently | | HW RESET
| | |and wait to do | |
| |<--+ | |
| | send pervious cfg |<--+
| | (1000M FULL AN_ON) |
| +-------------------->|
| | read cfg(time task) |
| | (10M HALF AN_OFF) +---+
| |<--------------------+ | cfg take effect
| | reset command |<--+
| +-------------------->|
| | +---+
| | send pervious cfg | | HW RESET
| | (10M HALF AN_OFF) |<--+
| +-------------------->|
| | read cfg(time task) |
| | (10M HALF AN_OFF) +---+
| |<--------------------+ | cfg take effect
| | | |
| | read cfg(time task) |<--+
| | (10M HALF AN_OFF) |
| |<--------------------+
| | |
v v v

To avoid aboved situation, this patch introduced req_speed, req_duplex,
req_autoneg to store user's configuration and it only be used after
hardware reset and to recover user's configuration

Fixes: f5f2b3e4dcc0 ("net: hns3: add support for imp-controlled PHYs")
Signed-off-by: Peiyang Wang <wangpeiyang1@xxxxxxxxxx>
Signed-off-by: Jijie Shao <shaojijie@xxxxxxxxxx>
---
.../ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 15 +++++++++------
.../ethernet/hisilicon/hns3/hns3pf/hclge_main.h | 3 +++
2 files changed, 12 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
index ff6a2ed23ddb..8043f1795dc7 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
@@ -1537,6 +1537,9 @@ static int hclge_configure(struct hclge_dev *hdev)
cfg.default_speed, ret);
return ret;
}
+ hdev->hw.mac.req_speed = hdev->hw.mac.speed;
+ hdev->hw.mac.req_autoneg = AUTONEG_ENABLE;
+ hdev->hw.mac.req_duplex = DUPLEX_FULL;
hclge_parse_link_mode(hdev, cfg.speed_ability);
@@ -3342,9 +3345,9 @@ hclge_set_phy_link_ksettings(struct hnae3_handle *handle,
return ret;
}
- hdev->hw.mac.autoneg = cmd->base.autoneg;
- hdev->hw.mac.speed = cmd->base.speed;
- hdev->hw.mac.duplex = cmd->base.duplex;
+ hdev->hw.mac.req_autoneg = cmd->base.autoneg;
+ hdev->hw.mac.req_speed = cmd->base.speed;
+ hdev->hw.mac.req_duplex = cmd->base.duplex;
linkmode_copy(hdev->hw.mac.advertising, cmd->link_modes.advertising);
return 0;
@@ -3377,9 +3380,9 @@ static int hclge_tp_port_init(struct hclge_dev *hdev)
if (!hnae3_dev_phy_imp_supported(hdev))
return 0;
- cmd.base.autoneg = hdev->hw.mac.autoneg;
- cmd.base.speed = hdev->hw.mac.speed;
- cmd.base.duplex = hdev->hw.mac.duplex;
+ cmd.base.autoneg = hdev->hw.mac.req_autoneg;
+ cmd.base.speed = hdev->hw.mac.req_speed;
+ cmd.base.duplex = hdev->hw.mac.req_duplex;
linkmode_copy(cmd.link_modes.advertising, hdev->hw.mac.advertising);
return hclge_set_phy_link_ksettings(&hdev->vport->nic, &cmd);
diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h
index e821dd2f1528..e3c69be8256f 100644
--- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h
+++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h
@@ -279,11 +279,14 @@ struct hclge_mac {
u8 media_type; /* port media type, e.g. fibre/copper/backplane */
u8 mac_addr[ETH_ALEN];
u8 autoneg;
+ u8 req_autoneg;
u8 duplex;
+ u8 req_duplex;
u8 support_autoneg;
u8 speed_type; /* 0: sfp speed, 1: active speed */
u8 lane_num;
u32 speed;
+ u32 req_speed;
u32 max_speed;
u32 speed_ability; /* speed ability supported by current media */
u32 module_type; /* sub media type, e.g. kr/cr/sr/lr */

Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@xxxxxxxxx>