Re: [PATCH v2 2/2] media: gc2145: implement basic dvp bus support

From: Andrey Skvortsov
Date: Sat May 04 2024 - 12:31:02 EST


Hi Alain,

thanks for the review.

On 24-04-26 18:38, Alain Volmat wrote:
> Hi Andrey,
>
> > --- a/drivers/media/i2c/gc2145.c
> > +++ b/drivers/media/i2c/gc2145.c
> > @@ -39,6 +39,10 @@
> > #define GC2145_REG_ANALOG_MODE1 CCI_REG8(0x17)
> > #define GC2145_REG_OUTPUT_FMT CCI_REG8(0x84)
> > #define GC2145_REG_SYNC_MODE CCI_REG8(0x86)
> > +#define GC2145_SYNC_MODE_VSYNC_POL BIT(0)
> > +#define GC2145_SYNC_MODE_HSYNC_POL BIT(1)
> > +#define GC2145_SYNC_MODE_OPCLK_POL BIT(2)
> > +#define GC2145_SYNC_MODE_OPCLK_GATE BIT(3)
>
> OPCLK_GATE added but never used.
All near bits were described. I decided to put description for this bit
as well, so all bits 0-5 are described in source code.

>
> > #define GC2145_SYNC_MODE_COL_SWITCH BIT(4)
> > #define GC2145_SYNC_MODE_ROW_SWITCH BIT(5)
> > #define GC2145_REG_BYPASS_MODE CCI_REG8(0x89)
> > @@ -53,6 +57,12 @@
> > #define GC2145_REG_GLOBAL_GAIN CCI_REG8(0xb0)
> > #define GC2145_REG_CHIP_ID CCI_REG16(0xf0)
> > #define GC2145_REG_PAD_IO CCI_REG8(0xf2)
> > +#define GC2145_REG_PLL_MODE1 CCI_REG8(0xf7)
> > +#define GC2145_REG_PLL_MODE2 CCI_REG8(0xf8)
> > +#define GC2145_REG_CM_MODE CCI_REG8(0xf9)
> > +#define GC2145_REG_CLK_DIV_MODE CCI_REG8(0xfa)
> > +#define GC2145_REG_ANALOG_PWC CCI_REG8(0xfc)
>
> All 5 define added but never used, those settings are part of the cci_sequences
> table. Maybe either keep the define and update the tables or drop the
> new define ?

> > +#define GC2145_REG_PAD_IO CCI_REG8(0xf2)
>
> Was already defined in the existing code, see above.
Thanks, I'll drop all unneeded defines in v3.


> > @@ -773,6 +784,38 @@ static int gc2145_set_pad_format(struct v4l2_subdev *sd,
> > return 0;
> > }
> >
> > +static int gc2145_config_dvp_mode(struct gc2145 *gc2145,
> > + const struct gc2145_format *gc2145_format)
>
> alignment ?
Thanks.

> > +{
> > + int ret = 0;
> > + u64 sync_mode;
> > + int flags;
> > +
> > + flags = gc2145->ep.bus.parallel.flags;
>
> int flags = gc2145->ep.bus.parallel.flags;
> ?
Fix in v3.

> > @@ -1244,36 +1292,57 @@ static int gc2145_check_hwcfg(struct device *dev)
> > return -EINVAL;
> > }
> >
> > - ret = v4l2_fwnode_endpoint_alloc_parse(endpoint, &ep_cfg);
> > +
>
> no new line here.
ok.

> > + gc2145->ep.bus_type = V4L2_MBUS_CSI2_DPHY;
> > + ret = v4l2_fwnode_endpoint_alloc_parse(endpoint, &gc2145->ep);
> > + if (ret) {
> > + gc2145->ep.bus_type = V4L2_MBUS_PARALLEL;
> > + ret = v4l2_fwnode_endpoint_alloc_parse(endpoint, &gc2145->ep);
> > + }
> > fwnode_handle_put(endpoint);
> > - if (ret)
> > + if (ret) {
> > + dev_err(dev, "could not parse endpoint\n");
> > return ret;
> > -
> > - /* Check the number of MIPI CSI2 data lanes */
> > - if (ep_cfg.bus.mipi_csi2.num_data_lanes != 2) {
> > - dev_err(dev, "only 2 data lanes are currently supported\n");
> > - ret = -EINVAL;
> > - goto out;
> > }
> >
> > - /* Check the link frequency set in device tree */
> > - if (!ep_cfg.nr_of_link_frequencies) {
> > - dev_err(dev, "link-frequency property not found in DT\n");
> > + switch (gc2145->ep.bus_type) {
> > + case V4L2_MBUS_CSI2_DPHY:
> > + /* Check the link frequency set in device tree */
> > + if (!gc2145->ep.nr_of_link_frequencies) {
> > + dev_err(dev, "link-frequencies property not found in DT\n");
> > + ret = -EINVAL;
> > + goto out;
> > + }
>
> any reason for change of the if order ? before num_data_lanes was
> checked first, then nr_of_link_frequencies, then 3 link_frequencies.

No reason. I'll change order like it was before in v3.

> > +
> > + /* Check the number of MIPI CSI2 data lanes */
> > + if (gc2145->ep.bus.mipi_csi2.num_data_lanes != 2) {
> > + dev_err(dev, "only 2 data lanes are currently supported\n");
> > + ret = -EINVAL;
> > + goto out;
> > + }
> > +
> > + if (gc2145->ep.nr_of_link_frequencies != 3 ||
> > + gc2145->ep.link_frequencies[0] != GC2145_640_480_LINKFREQ ||
> > + gc2145->ep.link_frequencies[1] != GC2145_1280_720_LINKFREQ ||
> > + gc2145->ep.link_frequencies[2] != GC2145_1600_1200_LINKFREQ) {
>
> alignment
Thanks.

>
> > + dev_err(dev, "Invalid link-frequencies provided\n");
> > + ret = -EINVAL;
> > + goto out;
> > + }
> > + break;
> > +
>
> no newline here
ok

--
Best regards,
Andrey Skvortsov