Re: [PATCH 2/4] PCI: pciehp: bail out if pci_hp_add_bridge() fails

[Lukas Wunner]

On Sat, May 04, 2024 at 11:35:29AM +0200, Nam Cao wrote:
> On Sat, May 04, 2024 at 10:54:15AM +0200, Lukas Wunner wrote:
> > On Fri, May 03, 2024 at 09:23:20PM +0200, Nam Cao wrote:
> > > If there is no bus number available for the downstream bus of the
> > > hot-plugged bridge, pci_hp_add_bridge() will fail. The driver proceeds
> > > regardless, and the kernel crashes.
> > > 
> > > Abort if pci_hp_add_bridge() fails.
> > [...]
> > > --- a/drivers/pci/hotplug/pciehp_pci.c
> > > +++ b/drivers/pci/hotplug/pciehp_pci.c
> > > @@ -58,8 +58,13 @@ int pciehp_configure_device(struct controller *ctrl)
> > >  		goto out;
> > >  	}
> > >  
> > > -	for_each_pci_bridge(dev, parent)
> > > -		pci_hp_add_bridge(dev);
> > > +	for_each_pci_bridge(dev, parent) {
> > > +		if (pci_hp_add_bridge(dev)) {
> > > +			pci_stop_and_remove_bus_device(dev);
> > > +			ret = -EINVAL;
> > > +			goto out;
> > > +		}
> > > +	}
> > 
> > Is the pci_stop_and_remove_bus_device() really necessary here?
> > Why not just leave the bridge as is, without any child devices?
> 
> pci_stop_and_remove_bus_device() is not necessary to prevent kernel
> crashing. But without this, we cannot hot-plug any other devices to this
> slot afterward, despite the bridge has already been removed. Below is what
> happens without pci_stop_and_remove_bus_device().
> 
> First, we hotplug a bridge. That fails, so QEMU removes this bridge:
> (qemu) device_add pci-bridge,id=br2,bus=br1,chassis_nr=19,addr=1
> [    9.289609] shpchp 0000:01:00.0: Latch close on Slot(1-1)
> [    9.291145] shpchp 0000:01:00.0: Button pressed on Slot(1-1)
> [    9.292705] shpchp 0000:01:00.0: Card present on Slot(1-1)
> [    9.294369] shpchp 0000:01:00.0: PCI slot #1-1 - powering on due to button press
> [   15.529997] pci 0000:02:01.0: [1b36:0001] type 01 class 0x060400 conventional PCI bridge
> [   15.533907] pci 0000:02:01.0: BAR 0 [mem 0x00000000-0x000000ff 64bit]
> [   15.535802] pci 0000:02:01.0: PCI bridge to [bus 00]
> [   15.538519] pci 0000:02:01.0:   bridge window [io  0x0000-0x0fff]
> [   15.540261] pci 0000:02:01.0:   bridge window [mem 0x00000000-0x000fffff]
> [   15.543486] pci 0000:02:01.0:   bridge window [mem 0x00000000-0x000fffff 64bit pref]
> [   15.547151] pci 0000:02:01.0: No bus number available for hot-added bridge
> [   15.549067] shpchp 0000:01:00.0: Cannot add device at 0000:02:01
> [   15.553104] shpchp 0000:01:00.0: Latch open on Slot(1-1)
> [   15.555246] shpchp 0000:01:00.0: Card not present on Slot(1-1)

I'm not familiar with shpchp, I don't understand why it's thinking
that there's no card after it failed to find a bus number.

Could you reproduce with pciehp instead of shpchp please?

Thanks,

Lukas