[PATCH v1 08/13] serial: 8250_exar: Decrease indentation level

From: Andy Shevchenko
Date: Thu May 02 2024 - 10:48:41 EST


Decrease indentation level in some places.
No functional change intended.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
---
drivers/tty/serial/8250/8250_exar.c | 100 ++++++++++++++--------------
1 file changed, 50 insertions(+), 50 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index 4e683ca76de0..1f04d4562878 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -607,28 +607,30 @@ pci_fastcom335_setup(struct exar8250 *priv, struct pci_dev *pcidev,
writeb(32, p + UART_EXAR_TXTRG);
writeb(32, p + UART_EXAR_RXTRG);

+ /* Skip the initial (per device) setup */
+ if (idx)
+ return 0;
+
/*
* Setup Multipurpose Input/Output pins.
*/
- if (idx == 0) {
- switch (pcidev->device) {
- case PCI_DEVICE_ID_COMMTECH_4222PCI335:
- case PCI_DEVICE_ID_COMMTECH_4224PCI335:
- writeb(0x78, p + UART_EXAR_MPIOLVL_7_0);
- writeb(0x00, p + UART_EXAR_MPIOINV_7_0);
- writeb(0x00, p + UART_EXAR_MPIOSEL_7_0);
- break;
- case PCI_DEVICE_ID_COMMTECH_2324PCI335:
- case PCI_DEVICE_ID_COMMTECH_2328PCI335:
- writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
- writeb(0xc0, p + UART_EXAR_MPIOINV_7_0);
- writeb(0xc0, p + UART_EXAR_MPIOSEL_7_0);
- break;
- }
- writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
- writeb(0x00, p + UART_EXAR_MPIO3T_7_0);
- writeb(0x00, p + UART_EXAR_MPIOOD_7_0);
+ switch (pcidev->device) {
+ case PCI_DEVICE_ID_COMMTECH_4222PCI335:
+ case PCI_DEVICE_ID_COMMTECH_4224PCI335:
+ writeb(0x78, p + UART_EXAR_MPIOLVL_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOINV_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOSEL_7_0);
+ break;
+ case PCI_DEVICE_ID_COMMTECH_2324PCI335:
+ case PCI_DEVICE_ID_COMMTECH_2328PCI335:
+ writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
+ writeb(0xc0, p + UART_EXAR_MPIOINV_7_0);
+ writeb(0xc0, p + UART_EXAR_MPIOSEL_7_0);
+ break;
}
+ writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
+ writeb(0x00, p + UART_EXAR_MPIO3T_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOOD_7_0);

return 0;
}
@@ -853,21 +855,19 @@ static enum cti_port_type cti_get_port_type_xr17v35x(struct exar8250 *priv,
port_flags = exar_ee_read(priv, offset);

port_type = FIELD_GET(CTI_EE_MASK_PORT_FLAGS_TYPE, port_flags);
- if (!CTI_PORT_TYPE_VALID(port_type)) {
- /*
- * If the port type is missing the card assume it is a
- * RS232/RS422/RS485 card to be safe.
- *
- * There is one known board (BEG013) that only has
- * 3 of 4 port types written to the EEPROM so this
- * acts as a work around.
- */
- dev_warn(&pcidev->dev,
- "failed to get port %d type from EEPROM\n", port_num);
- port_type = CTI_PORT_TYPE_RS232_422_485_HW;
- }
+ if (CTI_PORT_TYPE_VALID(port_type))
+ return port_type;

- return port_type;
+ /*
+ * If the port type is missing the card assume it is a
+ * RS232/RS422/RS485 card to be safe.
+ *
+ * There is one known board (BEG013) that only has 3 of 4 port types
+ * written to the EEPROM so this acts as a work around.
+ */
+ dev_warn(&pcidev->dev, "failed to get port %d type from EEPROM\n", port_num);
+
+ return CTI_PORT_TYPE_RS232_422_485_HW;
}

static int cti_rs485_config_mpio_tristate(struct uart_port *port,
@@ -1190,11 +1190,10 @@ static void setup_gpio(struct pci_dev *pcidev, u8 __iomem *p)
* devices will export them as GPIOs, so we pre-configure them safely
* as inputs.
*/
-
u8 dir = 0x00;

if ((pcidev->vendor == PCI_VENDOR_ID_EXAR) &&
- (pcidev->subsystem_vendor != PCI_VENDOR_ID_SEALEVEL)) {
+ (pcidev->subsystem_vendor != PCI_VENDOR_ID_SEALEVEL)) {
// Configure GPIO as inputs for Commtech adapters
dir = 0xff;
} else {
@@ -1284,27 +1283,28 @@ static int sealevel_rs485_config(struct uart_port *port, struct ktermios *termio
if (ret)
return ret;

- if (rs485->flags & SER_RS485_ENABLED) {
- old_lcr = readb(p + UART_LCR);
+ if (!(rs485->flags & SER_RS485_ENABLED))
+ return 0;

- /* Set EFR[4]=1 to enable enhanced feature registers */
- efr = readb(p + UART_XR_EFR);
- efr |= UART_EFR_ECB;
- writeb(efr, p + UART_XR_EFR);
+ old_lcr = readb(p + UART_LCR);

- /* Set MCR to use DTR as Auto-RS485 Enable signal */
- writeb(UART_MCR_OUT1, p + UART_MCR);
+ /* Set EFR[4]=1 to enable enhanced feature registers */
+ efr = readb(p + UART_XR_EFR);
+ efr |= UART_EFR_ECB;
+ writeb(efr, p + UART_XR_EFR);

- /* Set LCR[7]=1 to enable access to DLD register */
- writeb(old_lcr | UART_LCR_DLAB, p + UART_LCR);
+ /* Set MCR to use DTR as Auto-RS485 Enable signal */
+ writeb(UART_MCR_OUT1, p + UART_MCR);

- /* Set DLD[7]=1 for inverted RS485 Enable logic */
- dld = readb(p + UART_EXAR_DLD);
- dld |= UART_EXAR_DLD_485_POLARITY;
- writeb(dld, p + UART_EXAR_DLD);
+ /* Set LCR[7]=1 to enable access to DLD register */
+ writeb(old_lcr | UART_LCR_DLAB, p + UART_LCR);

- writeb(old_lcr, p + UART_LCR);
- }
+ /* Set DLD[7]=1 for inverted RS485 Enable logic */
+ dld = readb(p + UART_EXAR_DLD);
+ dld |= UART_EXAR_DLD_485_POLARITY;
+ writeb(dld, p + UART_EXAR_DLD);
+
+ writeb(old_lcr, p + UART_LCR);

return 0;
}
--
2.43.0.rc1.1336.g36b5255a03ac