Re: [PATCH v9 08/10] arm64: dts: qcom: sc8280xp: Add multiport controller node for SC8280

[Konrad Dybcio]

On 21.06.2023 06:36, Krishna Kurapati wrote:
> Add USB and DWC3 node for tertiary port of SC8280 along with multiport
> IRQ's and phy's. This will be used as a base for SA8295P and SA8295-Ride
> platforms.
> 
> Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 77 ++++++++++++++++++++++++++
>  1 file changed, 77 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> index 8fa9fbfe5d00..0dfa350ea3b3 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> @@ -3013,6 +3013,83 @@ system-cache-controller@9200000 {
>  			interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
>  		};
>  
> +		usb_2: usb@a4f8800 {
> +			compatible = "qcom,sc8280xp-dwc3-mp", "qcom,dwc3";
> +			reg = <0 0x0a4f8800 0 0x400>;

> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
These three properties, please stick just before status

> +
> +			clocks = <&gcc GCC_CFG_NOC_USB3_MP_AXI_CLK>,
> +				 <&gcc GCC_USB30_MP_MASTER_CLK>,
> +				 <&gcc GCC_AGGRE_USB3_MP_AXI_CLK>,
> +				 <&gcc GCC_USB30_MP_SLEEP_CLK>,
> +				 <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
> +				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
> +				 <&gcc GCC_AGGRE_USB_NOC_NORTH_AXI_CLK>,
> +				 <&gcc GCC_AGGRE_USB_NOC_SOUTH_AXI_CLK>,
> +				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
> +			clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
> +				      "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";
Please make it one per line

> +
> +			assigned-clocks = <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
> +					  <&gcc GCC_USB30_MP_MASTER_CLK>;
> +			assigned-clock-rates = <19200000>, <200000000>;
And here

> +
> +			interrupts-extended = <&pdc 127 IRQ_TYPE_EDGE_RISING>,
> +					      <&pdc 126 IRQ_TYPE_EDGE_RISING>,
> +					      <&pdc 129 IRQ_TYPE_EDGE_RISING>,
> +					      <&pdc 128 IRQ_TYPE_EDGE_RISING>,
> +					      <&pdc 131 IRQ_TYPE_EDGE_RISING>,
> +					      <&pdc 130 IRQ_TYPE_EDGE_RISING>,
> +					      <&pdc 133 IRQ_TYPE_EDGE_RISING>,
> +					      <&pdc 132 IRQ_TYPE_EDGE_RISING>,
> +					      <&pdc 16 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>,
Not a comment to the patch, but very nice that Qcom ensured every
endpoint is wakeup-capable, this used not to be the case before :D

> +					      <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&intc GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&intc GIC_SPI 857 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&intc GIC_SPI 856 IRQ_TYPE_LEVEL_HIGH>;
> +
Remove this newline

> +			interrupt-names = "dp1_hs_phy_irq", "dm1_hs_phy_irq",
> +					  "dp2_hs_phy_irq", "dm2_hs_phy_irq",
> +					  "dp3_hs_phy_irq", "dm3_hs_phy_irq",
> +					  "dp4_hs_phy_irq", "dm4_hs_phy_irq",
> +					  "ss1_phy_irq", "ss2_phy_irq",
> +					  "pwr_event_1",
> +					  "pwr_event_2",
> +					  "pwr_event_3",
> +					  "pwr_event_4";
Please make it one per line

> +
> +			power-domains = <&gcc USB30_MP_GDSC>;
> +			required-opps = <&rpmhpd_opp_nom>;
> +
> +			resets = <&gcc GCC_USB30_MP_BCR>;
> +
> +			interconnects = <&aggre1_noc MASTER_USB3_MP 0 &mc_virt SLAVE_EBI1 0>,
> +					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_MP 0>;
> +			interconnect-names = "usb-ddr", "apps-usb";
> +
> +			wakeup-source;
> +
> +			status = "disabled";
> +
> +			usb_2_dwc3: usb@a400000 {
> +				compatible = "snps,dwc3";
> +				reg = <0 0x0a400000 0 0xcd00>;
> +				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> +				iommus = <&apps_smmu 0x800 0x0>;
> +				phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>,
> +				       <&usb_2_hsphy1>, <&usb_2_qmpphy1>,
> +				       <&usb_2_hsphy2>,
> +				       <&usb_2_hsphy3>;
And here
> +				phy-names = "usb2-port0", "usb3-port0",
> +					    "usb2-port1", "usb3-port1",
> +					    "usb2-port2",
> +					    "usb2-port3";
And here

Thanks for working on this!

Konrad
> +			};
> +		};
> +
>  		usb_0: usb@a6f8800 {
>  			compatible = "qcom,sc8280xp-dwc3", "qcom,dwc3";
>  			reg = <0 0x0a6f8800 0 0x400>;