Re: [PATCH V6] can: usb: f81604: add Fintek F81604 support
From: Vincent MAILHOL
Date: Sun May 07 2023 - 04:37:40 EST
Hi Peter,
Thanks for the v6. I added two nitpicks. It is up to you where you
want or not to fix those. Aside from that, it looks good.
Reviewed-by: Vincent Mailhol <mailhol.vincent@xxxxxxxxxx>
Le ven. 5 mai 2023 à 11:25, Ji-Ze Hong (Peter Hong)
<peter_hong@xxxxxxxxxxxxx> a écrit :
>
> This patch adds support for Fintek USB to 2CAN controller.
>
> Signed-off-by: Ji-Ze Hong (Peter Hong) <peter_hong@xxxxxxxxxxxxx>
> ---
> Changelog:
> v6:
> 1. Remove non-used define and change constant mask to GENMASK().
> 2. Move some variables declaration from function start to block start.
> 3. Move some variables initization into declaration.
> 4. Change variable "id" in f81604_start_xmit() only for CAN ID usage.
>
> v5:
> 1. Change all u8 *buff to struct f81604_int_data/f81604_can_frame.
> 2. Change all netdev->dev_id to netdev->dev_port.
> 3. Remove over design for f81604_process_rx_packet(). This device only
> report a frame at once, so the f81604_process_rx_packet() are reduced
> to process 1 frame.
>
> v4:
> 1. Remove f81604_prepare_urbs/f81604_remove_urbs() and alloc URB/buffer
> dynamically in f81604_register_urbs(), using "urbs_anchor" for manage
> all rx/int URBs.
> 2. Add F81604 to MAINTAINERS list.
> 3. Change handle_clear_reg_work/handle_clear_overrun_work to single
> clear_reg_work and using bitwise "clear_flags" to record it.
> 4. Move __f81604_set_termination in front of f81604_probe() to avoid
> rarely racing condition.
> 5. Add __aligned to struct f81604_int_data / f81604_sff / f81604_eff.
> 6. Add aligned operations in f81604_start_xmit/f81604_process_rx_packet().
> 7. Change lots of CANBUS functions first parameter from struct usb_device*
> to struct f81604_port_priv *priv. But remain f81604_write / f81604_read
> / f81604_update_bits() as struct usb_device* for
> __f81604_set_termination() in probe() stage.
> 8. Simplify f81604_read_int_callback() and separate into
> f81604_handle_tx / f81604_handle_can_bus_errors() functions.
>
> v3:
> 1. Change CAN clock to using MEGA units.
> 2. Remove USB set/get retry, only remain SJA1000 reset/operation retry.
> 3. Fix all numberic constant to define.
> 4. Add terminator control. (only 0 & 120 ohm)
> 5. Using struct data to represent INT/TX/RX endpoints data instead byte
> arrays.
> 6. Error message reports changed from %d to %pe for mnemotechnic values.
> 7. Some bit operations are changed to FIELD_PREP().
> 8. Separate TX functions from f81604_read_int_callback().
> 9. cf->can_id |= CAN_ERR_CNT in f81604_read_int_callback to report valid
> TX/RX error counts.
> 10. Move f81604_prepare_urbs/f81604_remove_urbs() from CAN open/close() to
> USB probe/disconnect().
> 11. coding style refactoring.
>
> v2:
> 1. coding style refactoring.
> 2. some const number are defined to describe itself.
> 3. fix wrong usage for can_get_echo_skb() in f81604_write_bulk_callback().
>
> MAINTAINERS | 6 +
> drivers/net/can/usb/Kconfig | 12 +
> drivers/net/can/usb/Makefile | 1 +
> drivers/net/can/usb/f81604.c | 1205 ++++++++++++++++++++++++++++++++++
> 4 files changed, 1224 insertions(+)
> create mode 100644 drivers/net/can/usb/f81604.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index f375bbf3bc80..fa573f637c2f 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -8058,6 +8058,12 @@ S: Maintained
> F: drivers/hwmon/f75375s.c
> F: include/linux/f75375s.h
>
> +FINTEK F81604 USB to 2xCANBUS DEVICE DRIVER
> +M: Ji-Ze Hong (Peter Hong) <peter_hong@xxxxxxxxxxxxx>
> +L: linux-can@xxxxxxxxxxxxxxx
> +S: Maintained
> +F: drivers/net/can/usb/f81604.c
> +
> FIREWIRE AUDIO DRIVERS and IEC 61883-1/6 PACKET STREAMING ENGINE
> M: Clemens Ladisch <clemens@xxxxxxxxxx>
> M: Takashi Sakamoto <o-takashi@xxxxxxxxxxxxx>
> diff --git a/drivers/net/can/usb/Kconfig b/drivers/net/can/usb/Kconfig
> index 445504ababce..58fcd2b34820 100644
> --- a/drivers/net/can/usb/Kconfig
> +++ b/drivers/net/can/usb/Kconfig
> @@ -38,6 +38,18 @@ config CAN_ETAS_ES58X
> To compile this driver as a module, choose M here: the module
> will be called etas_es58x.
>
> +config CAN_F81604
> + tristate "Fintek F81604 USB to 2CAN interface"
> + help
> + This driver supports the Fintek F81604 USB to 2CAN interface.
> + The device can support CAN2.0A/B protocol and also support
> + 2 output pins to control external terminator (optional).
> +
> + To compile this driver as a module, choose M here: the module will
> + be called f81604.
> +
> + (see also https://www.fintek.com.tw).
> +
> config CAN_GS_USB
> tristate "Geschwister Schneider UG and candleLight compatible interfaces"
> help
> diff --git a/drivers/net/can/usb/Makefile b/drivers/net/can/usb/Makefile
> index 1ea16be5743b..8b11088e9a59 100644
> --- a/drivers/net/can/usb/Makefile
> +++ b/drivers/net/can/usb/Makefile
> @@ -7,6 +7,7 @@ obj-$(CONFIG_CAN_8DEV_USB) += usb_8dev.o
> obj-$(CONFIG_CAN_EMS_USB) += ems_usb.o
> obj-$(CONFIG_CAN_ESD_USB) += esd_usb.o
> obj-$(CONFIG_CAN_ETAS_ES58X) += etas_es58x/
> +obj-$(CONFIG_CAN_F81604) += f81604.o
> obj-$(CONFIG_CAN_GS_USB) += gs_usb.o
> obj-$(CONFIG_CAN_KVASER_USB) += kvaser_usb/
> obj-$(CONFIG_CAN_MCBA_USB) += mcba_usb.o
> diff --git a/drivers/net/can/usb/f81604.c b/drivers/net/can/usb/f81604.c
> new file mode 100644
> index 000000000000..36839140ba5f
> --- /dev/null
> +++ b/drivers/net/can/usb/f81604.c
> @@ -0,0 +1,1205 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/* Fintek F81604 USB-to-2CAN controller driver.
> + *
> + * Copyright (C) 2023 Ji-Ze Hong (Peter Hong) <peter_hong@xxxxxxxxxxxxx>
> + */
> +#include <linux/bitfield.h>
> +#include <linux/netdevice.h>
> +#include <linux/units.h>
> +#include <linux/usb.h>
> +
> +#include <linux/can.h>
> +#include <linux/can/dev.h>
> +#include <linux/can/error.h>
> +#include <linux/can/platform/sja1000.h>
> +
> +#include <asm-generic/unaligned.h>
> +
> +/* vendor and product id */
> +#define F81604_VENDOR_ID 0x2c42
> +#define F81604_PRODUCT_ID 0x1709
> +#define F81604_CAN_CLOCK (12 * MEGA)
> +#define F81604_MAX_DEV 2
> +#define F81604_SET_DEVICE_RETRY 10
> +
> +#define F81604_USB_TIMEOUT 2000
> +#define F81604_SET_GET_REGISTER 0xA0
> +#define F81604_PORT_OFFSET 0x1000
> +#define F81604_MAX_RX_URBS 4
> +
> +#define F81604_CMD_DATA 0x00
> +
> +#define F81604_DLC_LEN_MASK GENMASK(3, 0)
> +#define F81604_DLC_EFF_BIT BIT(7)
> +#define F81604_DLC_RTR_BIT BIT(6)
> +
> +#define F81604_SFF_SHIFT 5
> +#define F81604_EFF_SHIFT 3
> +
> +#define F81604_BRP_MASK GENMASK(5, 0)
> +#define F81604_SJW_MASK GENMASK(7, 6)
> +
> +#define F81604_SEG1_MASK GENMASK(3, 0)
> +#define F81604_SEG2_MASK GENMASK(6, 4)
> +
> +#define F81604_CLEAR_ALC 0
> +#define F81604_CLEAR_ECC 1
> +#define F81604_CLEAR_OVERRUN 2
> +
> +/* device setting */
> +#define F81604_CTRL_MODE_REG 0x80
> +#define F81604_TX_ONESHOT (0x03 << 3)
> +#define F81604_TX_NORMAL (0x01 << 3)
> +#define F81604_RX_AUTO_RELEASE_BUF BIT(1)
> +#define F81604_INT_WHEN_CHANGE BIT(0)
> +
> +#define F81604_TERMINATOR_REG 0x105
> +#define F81604_CAN0_TERM BIT(2)
> +#define F81604_CAN1_TERM BIT(3)
> +
> +#define F81604_TERMINATION_DISABLED CAN_TERMINATION_DISABLED
> +#define F81604_TERMINATION_ENABLED 120
> +
> +/* SJA1000 registers - manual section 6.4 (Pelican Mode) */
> +#define F81604_SJA1000_MOD 0x00
> +#define F81604_SJA1000_CMR 0x01
> +#define F81604_SJA1000_IR 0x03
> +#define F81604_SJA1000_IER 0x04
> +#define F81604_SJA1000_ALC 0x0B
> +#define F81604_SJA1000_ECC 0x0C
> +#define F81604_SJA1000_RXERR 0x0E
> +#define F81604_SJA1000_TXERR 0x0F
> +#define F81604_SJA1000_ACCC0 0x10
> +#define F81604_SJA1000_ACCM0 0x14
> +#define F81604_MAX_FILTER_CNT 4
> +
> +/* Common registers - manual section 6.5 */
> +#define F81604_SJA1000_BTR0 0x06
> +#define F81604_SJA1000_BTR1 0x07
> +#define F81604_SJA1000_BTR1_SAMPLE_TRIPLE BIT(7)
> +#define F81604_SJA1000_OCR 0x08
> +#define F81604_SJA1000_CDR 0x1F
> +
> +/* mode register */
> +#define F81604_SJA1000_MOD_RM 0x01
> +#define F81604_SJA1000_MOD_LOM 0x02
> +#define F81604_SJA1000_MOD_STM 0x04
> +
> +/* commands */
> +#define F81604_SJA1000_CMD_CDO 0x08
> +
> +/* interrupt sources */
> +#define F81604_SJA1000_IRQ_BEI 0x80
> +#define F81604_SJA1000_IRQ_ALI 0x40
> +#define F81604_SJA1000_IRQ_EPI 0x20
> +#define F81604_SJA1000_IRQ_DOI 0x08
> +#define F81604_SJA1000_IRQ_EI 0x04
> +#define F81604_SJA1000_IRQ_TI 0x02
> +#define F81604_SJA1000_IRQ_RI 0x01
> +#define F81604_SJA1000_IRQ_ALL 0xFF
> +#define F81604_SJA1000_IRQ_OFF 0x00
> +
> +/* status register content */
> +#define F81604_SJA1000_SR_BS 0x80
> +#define F81604_SJA1000_SR_ES 0x40
> +#define F81604_SJA1000_SR_TCS 0x08
> +
> +/* ECC register */
> +#define F81604_SJA1000_ECC_SEG 0x1F
> +#define F81604_SJA1000_ECC_DIR 0x20
> +#define F81604_SJA1000_ECC_BIT 0x00
> +#define F81604_SJA1000_ECC_FORM 0x40
> +#define F81604_SJA1000_ECC_STUFF 0x80
> +#define F81604_SJA1000_ECC_MASK 0xc0
> +
> +/* ALC register */
> +#define F81604_SJA1000_ALC_MASK 0x1f
> +
> +/* table of devices that work with this driver */
> +static const struct usb_device_id f81604_table[] = {
> + { USB_DEVICE(F81604_VENDOR_ID, F81604_PRODUCT_ID) },
> + {} /* Terminating entry */
> +};
> +
> +MODULE_DEVICE_TABLE(usb, f81604_table);
> +
> +static const struct ethtool_ops f81604_ethtool_ops = {
> + .get_ts_info = ethtool_op_get_ts_info,
> +};
> +
> +static const u16 f81604_termination[] = { F81604_TERMINATION_DISABLED,
> + F81604_TERMINATION_ENABLED };
> +
> +struct f81604_priv {
> + struct net_device *netdev[F81604_MAX_DEV];
> +};
> +
> +struct f81604_port_priv {
> + struct can_priv can;
> + struct net_device *netdev;
> + struct sk_buff *echo_skb;
> +
> + unsigned long clear_flags;
> + struct work_struct clear_reg_work;
> +
> + struct usb_device *dev;
> + struct usb_interface *intf;
> +
> + struct usb_anchor urbs_anchor;
> +};
> +
> +/* Interrupt endpoint data format:
> + * Byte 0: Status register.
> + * Byte 1: Interrupt register.
> + * Byte 2: Interrupt enable register.
> + * Byte 3: Arbitration lost capture(ALC) register.
> + * Byte 4: Error code capture(ECC) register.
> + * Byte 5: Error warning limit register.
> + * Byte 6: RX error counter register.
> + * Byte 7: TX error counter register.
> + * Byte 8: Reserved.
> + */
> +struct f81604_int_data {
> + u8 sr;
> + u8 isrc;
> + u8 ier;
> + u8 alc;
> + u8 ecc;
> + u8 ewlr;
> + u8 rxerr;
> + u8 txerr;
> + u8 val;
> +} __packed __aligned(4);
> +
> +struct f81604_sff {
> + __be16 id;
> + u8 data[CAN_MAX_DLEN];
> +} __packed __aligned(2);
> +
> +struct f81604_eff {
> + __be32 id;
> + u8 data[CAN_MAX_DLEN];
> +} __packed __aligned(2);
> +
> +struct f81604_can_frame {
> + u8 cmd;
> +
> + /* According for F81604 DLC define:
> + * bit 3~0: data length (0~8)
> + * bit6: is RTR flag.
> + * bit7: is EFF frame.
> + */
> + u8 dlc;
> +
> + union {
> + struct f81604_sff sff;
> + struct f81604_eff eff;
> + };
> +} __packed __aligned(2);
> +
> +static const u8 bulk_in_addr[F81604_MAX_DEV] = { 2, 4 };
> +static const u8 bulk_out_addr[F81604_MAX_DEV] = { 1, 3 };
> +static const u8 int_in_addr[F81604_MAX_DEV] = { 1, 3 };
> +
> +static int f81604_write(struct usb_device *dev, u16 reg, u8 data)
> +{
> + int ret;
> +
> + ret = usb_control_msg_send(dev, 0, F81604_SET_GET_REGISTER,
> + USB_TYPE_VENDOR | USB_DIR_OUT, 0, reg,
> + &data, sizeof(data), F81604_USB_TIMEOUT,
> + GFP_KERNEL);
> + if (ret)
> + dev_err(&dev->dev, "%s: reg: %x data: %x failed: %pe\n",
> + __func__, reg, data, ERR_PTR(ret));
> +
> + return ret;
> +}
> +
> +static int f81604_read(struct usb_device *dev, u16 reg, u8 *data)
> +{
> + int ret;
> +
> + ret = usb_control_msg_recv(dev, 0, F81604_SET_GET_REGISTER,
> + USB_TYPE_VENDOR | USB_DIR_IN, 0, reg, data,
> + sizeof(*data), F81604_USB_TIMEOUT,
> + GFP_KERNEL);
> +
> + if (ret < 0)
> + dev_err(&dev->dev, "%s: reg: %x failed: %pe\n", __func__, reg,
> + ERR_PTR(ret));
> +
> + return ret;
> +}
> +
> +static int f81604_update_bits(struct usb_device *dev, u16 reg, u8 mask,
> + u8 data)
> +{
> + int ret;
> + u8 tmp;
> +
> + ret = f81604_read(dev, reg, &tmp);
> + if (ret)
> + return ret;
> +
> + tmp &= ~mask;
> + tmp |= (mask & data);
> +
> + return f81604_write(dev, reg, tmp);
> +}
> +
> +static int f81604_sja1000_write(struct f81604_port_priv *priv, u16 reg,
> + u8 data)
> +{
> + int port = priv->netdev->dev_port;
> + int real_reg;
> +
> + real_reg = reg + F81604_PORT_OFFSET * port + F81604_PORT_OFFSET;
> + return f81604_write(priv->dev, real_reg, data);
> +}
> +
> +static int f81604_sja1000_read(struct f81604_port_priv *priv, u16 reg,
> + u8 *data)
> +{
> + int port = priv->netdev->dev_port;
> + int real_reg;
> +
> + real_reg = reg + F81604_PORT_OFFSET * port + F81604_PORT_OFFSET;
> + return f81604_read(priv->dev, real_reg, data);
> +}
> +
> +static int f81604_set_reset_mode(struct f81604_port_priv *priv)
> +{
> + int ret, i;
> + u8 tmp;
> +
> + /* disable interrupts */
> + ret = f81604_sja1000_write(priv, F81604_SJA1000_IER,
> + F81604_SJA1000_IRQ_OFF);
> + if (ret)
> + return ret;
> +
> + for (i = 0; i < F81604_SET_DEVICE_RETRY; i++) {
> + ret = f81604_sja1000_read(priv, F81604_SJA1000_MOD, &tmp);
> + if (ret)
> + return ret;
> +
> + /* check reset bit */
> + if (tmp & F81604_SJA1000_MOD_RM) {
> + priv->can.state = CAN_STATE_STOPPED;
> + return 0;
> + }
> +
> + /* reset chip */
> + ret = f81604_sja1000_write(priv, F81604_SJA1000_MOD,
> + F81604_SJA1000_MOD_RM);
> + if (ret)
> + return ret;
> + }
> +
> + return -EPERM;
> +}
> +
> +static int f81604_set_normal_mode(struct f81604_port_priv *priv)
> +{
> + u8 tmp, ier = 0;
> + u8 mod_reg = 0;
> + int ret, i;
> +
> + for (i = 0; i < F81604_SET_DEVICE_RETRY; i++) {
> + ret = f81604_sja1000_read(priv, F81604_SJA1000_MOD, &tmp);
> + if (ret)
> + return ret;
> +
> + /* check reset bit */
> + if ((tmp & F81604_SJA1000_MOD_RM) == 0) {
> + priv->can.state = CAN_STATE_ERROR_ACTIVE;
> + /* enable interrupts, RI handled by bulk-in */
> + ier = F81604_SJA1000_IRQ_ALL & ~F81604_SJA1000_IRQ_RI;
> + if (!(priv->can.ctrlmode &
> + CAN_CTRLMODE_BERR_REPORTING))
> + ier &= ~F81604_SJA1000_IRQ_BEI;
> +
> + return f81604_sja1000_write(priv, F81604_SJA1000_IER,
> + ier);
> + }
> +
> + /* set chip to normal mode */
> + if (priv->can.ctrlmode & CAN_CTRLMODE_LISTENONLY)
> + mod_reg |= F81604_SJA1000_MOD_LOM;
> + if (priv->can.ctrlmode & CAN_CTRLMODE_PRESUME_ACK)
> + mod_reg |= F81604_SJA1000_MOD_STM;
> +
> + ret = f81604_sja1000_write(priv, F81604_SJA1000_MOD, mod_reg);
> + if (ret)
> + return ret;
> + }
> +
> + return -EPERM;
> +}
> +
> +static int f81604_chipset_init(struct f81604_port_priv *priv)
> +{
> + int i, ret;
> +
> + /* set clock divider and output control register */
> + ret = f81604_sja1000_write(priv, F81604_SJA1000_CDR,
> + CDR_CBP | CDR_PELICAN);
> + if (ret)
> + return ret;
> +
> + /* set acceptance filter (accept all) */
> + for (i = 0; i < F81604_MAX_FILTER_CNT; ++i) {
> + ret = f81604_sja1000_write(priv, F81604_SJA1000_ACCC0 + i, 0);
> + if (ret)
> + return ret;
> + }
> +
> + for (i = 0; i < F81604_MAX_FILTER_CNT; ++i) {
> + ret = f81604_sja1000_write(priv, F81604_SJA1000_ACCM0 + i,
> + 0xFF);
> + if (ret)
> + return ret;
> + }
> +
> + return f81604_sja1000_write(priv, F81604_SJA1000_OCR,
> + OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL |
> + OCR_MODE_NORMAL);
> +}
> +
> +static void f81604_process_rx_packet(struct net_device *netdev,
> + struct f81604_can_frame *frame)
> +{
> + struct net_device_stats *stats = &netdev->stats;
> + struct can_frame *cf;
> + struct sk_buff *skb;
> +
> + if (frame->cmd != F81604_CMD_DATA)
> + return;
> +
> + skb = alloc_can_skb(netdev, &cf);
> + if (!skb) {
> + stats->rx_dropped++;
> + return;
> + }
> +
> + cf->len = can_cc_dlc2len(frame->dlc & F81604_DLC_LEN_MASK);
> +
> + if (frame->dlc & F81604_DLC_EFF_BIT) {
> + cf->can_id = get_unaligned_be32(&frame->eff.id) >>
> + F81604_EFF_SHIFT;
> + cf->can_id |= CAN_EFF_FLAG;
> +
> + if (!(frame->dlc & F81604_DLC_RTR_BIT))
> + memcpy(cf->data, frame->eff.data, cf->len);
> + } else {
> + cf->can_id = get_unaligned_be16(&frame->sff.id) >>
> + F81604_SFF_SHIFT;
> +
> + if (!(frame->dlc & F81604_DLC_RTR_BIT))
> + memcpy(cf->data, frame->sff.data, cf->len);
> + }
> +
> + if (frame->dlc & F81604_DLC_RTR_BIT)
> + cf->can_id |= CAN_RTR_FLAG;
> + else
> + stats->rx_bytes += cf->len;
> +
> + stats->rx_packets++;
> + netif_rx(skb);
> +}
> +
> +static void f81604_read_bulk_callback(struct urb *urb)
> +{
> + struct f81604_can_frame *frame = urb->transfer_buffer;
> + struct net_device *netdev = urb->context;
> + int ret;
> +
> + if (!netif_device_present(netdev))
> + return;
> +
> + if (urb->status)
> + netdev_info(netdev, "%s: URB aborted %pe\n", __func__,
> + ERR_PTR(urb->status));
> +
> + switch (urb->status) {
> + case 0: /* success */
> + break;
> +
> + case -ENOENT:
> + case -EPIPE:
> + case -EPROTO:
> + case -ESHUTDOWN:
> + return;
> +
> + default:
> + goto resubmit_urb;
> + }
> +
> + if (urb->actual_length != sizeof(*frame)) {
> + netdev_warn(netdev, "URB length %u not equal to %lu\n",
> + urb->actual_length, sizeof(*frame));
> + goto resubmit_urb;
> + }
> +
> + f81604_process_rx_packet(netdev, frame);
> +
> +resubmit_urb:
> + ret = usb_submit_urb(urb, GFP_ATOMIC);
> + if (ret == -ENODEV)
> + netif_device_detach(netdev);
> + else if (ret)
> + netdev_err(netdev,
> + "%s: failed to resubmit read bulk urb: %pe\n",
> + __func__, ERR_PTR(ret));
> +}
> +
> +static void f81604_handle_tx(struct f81604_port_priv *priv,
> + struct f81604_int_data *data)
> +{
> + struct net_device *netdev = priv->netdev;
> + struct net_device_stats *stats = &netdev->stats;
> +
> + /* transmission buffer released */
> + if (priv->can.ctrlmode & CAN_CTRLMODE_ONE_SHOT &&
> + !(data->sr & F81604_SJA1000_SR_TCS)) {
> + stats->tx_errors++;
> + can_free_echo_skb(netdev, 0, NULL);
> + } else {
> + /* transmission complete */
> + stats->tx_bytes += can_get_echo_skb(netdev, 0, NULL);
> + stats->tx_packets++;
> + }
> +
> + netif_wake_queue(netdev);
> +}
> +
> +static void f81604_handle_can_bus_errors(struct f81604_port_priv *priv,
> + struct f81604_int_data *data)
> +{
> + enum can_state can_state = priv->can.state;
> + struct net_device *netdev = priv->netdev;
> + struct net_device_stats *stats = &netdev->stats;
> + struct can_frame *cf;
> + struct sk_buff *skb;
> +
> + /* Note: ALC/ECC will not auto clear by read here, must be cleared by
> + * read register (via clear_reg_work).
> + */
> +
> + skb = alloc_can_err_skb(netdev, &cf);
> + if (skb) {
> + cf->can_id |= CAN_ERR_CNT;
> + cf->data[6] = data->txerr;
> + cf->data[7] = data->rxerr;
> + }
> +
> + if (data->isrc & F81604_SJA1000_IRQ_DOI) {
> + /* data overrun interrupt */
> + netdev_dbg(netdev, "data overrun interrupt\n");
> +
> + if (skb) {
> + cf->can_id |= CAN_ERR_CRTL;
> + cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
> + }
> +
> + stats->rx_over_errors++;
> + stats->rx_errors++;
> +
> + set_bit(F81604_CLEAR_OVERRUN, &priv->clear_flags);
> + }
> +
> + if (data->isrc & F81604_SJA1000_IRQ_EI) {
> + /* error warning interrupt */
> + netdev_dbg(netdev, "error warning interrupt\n");
> +
> + if (data->sr & F81604_SJA1000_SR_BS)
> + can_state = CAN_STATE_BUS_OFF;
> + else if (data->sr & F81604_SJA1000_SR_ES)
> + can_state = CAN_STATE_ERROR_WARNING;
> + else
> + can_state = CAN_STATE_ERROR_ACTIVE;
> + }
> +
> + if (data->isrc & F81604_SJA1000_IRQ_BEI) {
> + /* bus error interrupt */
> + netdev_dbg(netdev, "bus error interrupt\n");
> +
> + priv->can.can_stats.bus_error++;
> + stats->rx_errors++;
> +
> + if (skb) {
> + cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
> +
> + /* set error type */
> + switch (data->ecc & F81604_SJA1000_ECC_MASK) {
> + case F81604_SJA1000_ECC_BIT:
> + cf->data[2] |= CAN_ERR_PROT_BIT;
> + break;
> + case F81604_SJA1000_ECC_FORM:
> + cf->data[2] |= CAN_ERR_PROT_FORM;
> + break;
> + case F81604_SJA1000_ECC_STUFF:
> + cf->data[2] |= CAN_ERR_PROT_STUFF;
> + break;
> + default:
> + break;
> + }
> +
> + /* set error location */
> + cf->data[3] = data->ecc & F81604_SJA1000_ECC_SEG;
> +
> + /* Error occurred during transmission? */
> + if ((data->ecc & F81604_SJA1000_ECC_DIR) == 0)
> + cf->data[2] |= CAN_ERR_PROT_TX;
> + }
> +
> + set_bit(F81604_CLEAR_ECC, &priv->clear_flags);
> + }
> +
> + if (data->isrc & F81604_SJA1000_IRQ_EPI) {
> + if (can_state == CAN_STATE_ERROR_PASSIVE)
> + can_state = CAN_STATE_ERROR_WARNING;
> + else
> + can_state = CAN_STATE_ERROR_PASSIVE;
> +
> + /* error passive interrupt */
> + netdev_dbg(netdev, "error passive interrupt: %d\n", can_state);
> + }
> +
> + if (data->isrc & F81604_SJA1000_IRQ_ALI) {
> + /* arbitration lost interrupt */
> + netdev_dbg(netdev, "arbitration lost interrupt\n");
> +
> + priv->can.can_stats.arbitration_lost++;
> +
> + if (skb) {
> + cf->can_id |= CAN_ERR_LOSTARB;
> + cf->data[0] = data->alc & F81604_SJA1000_ALC_MASK;
> + }
> +
> + set_bit(F81604_CLEAR_ALC, &priv->clear_flags);
> + }
> +
> + if (can_state != priv->can.state) {
> + enum can_state tx_state, rx_state;
> +
> + tx_state = data->txerr >= data->rxerr ? can_state : 0;
> + rx_state = data->txerr <= data->rxerr ? can_state : 0;
> +
> + can_change_state(netdev, cf, tx_state, rx_state);
> +
> + if (can_state == CAN_STATE_BUS_OFF)
> + can_bus_off(netdev);
> + }
> +
> + if (priv->clear_flags)
> + schedule_work(&priv->clear_reg_work);
> +
> + if (skb)
> + netif_rx(skb);
> +}
> +
> +static void f81604_read_int_callback(struct urb *urb)
> +{
> + struct f81604_int_data *data = urb->transfer_buffer;
> + struct net_device *netdev = urb->context;
> + struct f81604_port_priv *priv;
> + int ret;
> +
> + priv = netdev_priv(netdev);
> +
> + if (!netif_device_present(netdev))
> + return;
> +
> + if (urb->status)
> + netdev_info(netdev, "%s: Int URB aborted: %pe\n", __func__,
> + ERR_PTR(urb->status));
> +
> + switch (urb->status) {
> + case 0: /* success */
> + break;
> +
> + case -ENOENT:
> + case -EPIPE:
> + case -EPROTO:
> + case -ESHUTDOWN:
> + return;
> +
> + default:
> + goto resubmit_urb;
> + }
> +
> + /* handle Errors */
> + if (data->isrc & (F81604_SJA1000_IRQ_DOI | F81604_SJA1000_IRQ_EI |
> + F81604_SJA1000_IRQ_BEI | F81604_SJA1000_IRQ_EPI |
> + F81604_SJA1000_IRQ_ALI))
> + f81604_handle_can_bus_errors(priv, data);
> +
> + /* handle TX */
> + if (priv->can.state != CAN_STATE_BUS_OFF &&
> + (data->isrc & F81604_SJA1000_IRQ_TI))
> + f81604_handle_tx(priv, data);
> +
> +resubmit_urb:
> + ret = usb_submit_urb(urb, GFP_ATOMIC);
> + if (ret == -ENODEV)
> + netif_device_detach(netdev);
> + else if (ret)
> + netdev_err(netdev, "%s: failed to resubmit int urb: %pe\n",
> + __func__, ERR_PTR(ret));
> +}
> +
> +static void f81604_unregister_urbs(struct f81604_port_priv *priv)
> +{
> + usb_kill_anchored_urbs(&priv->urbs_anchor);
> +}
> +
> +static int f81604_register_urbs(struct f81604_port_priv *priv)
> +{
> + struct net_device *netdev = priv->netdev;
> + struct f81604_int_data *int_data;
> + int id = netdev->dev_port;
> + struct urb *int_urb;
> + int rx_urb_cnt;
> + int ret;
Nitpick: your style is inconsistent. Sometimes you have a new line
before the goto or return, sometimes not.
> + for (rx_urb_cnt = 0; rx_urb_cnt < F81604_MAX_RX_URBS; ++rx_urb_cnt) {
> + struct f81604_can_frame *frame;
> + struct urb *rx_urb;
> +
> + rx_urb = usb_alloc_urb(0, GFP_KERNEL);
> + if (!rx_urb) {
> + ret = -ENOMEM;
> + break;
> + }
> +
> + frame = kmalloc(sizeof(*frame), GFP_KERNEL);
> + if (!frame) {
> + usb_free_urb(rx_urb);
> + ret = -ENOMEM;
> + break;
...no new line, ...
> + }
> +
> + usb_fill_bulk_urb(rx_urb, priv->dev,
> + usb_rcvbulkpipe(priv->dev, bulk_in_addr[id]),
> + frame, sizeof(*frame),
> + f81604_read_bulk_callback, netdev);
> +
> + rx_urb->transfer_flags |= URB_FREE_BUFFER;
> + usb_anchor_urb(rx_urb, &priv->urbs_anchor);
> +
> + ret = usb_submit_urb(rx_urb, GFP_KERNEL);
> + if (ret) {
> + usb_unanchor_urb(rx_urb);
> + usb_free_urb(rx_urb);
> +
> + break;
...new line, ...
> + }
> +
> + /* Drop reference, USB core will take care of freeing it */
> + usb_free_urb(rx_urb);
> + }
> +
> + if (rx_urb_cnt == 0) {
> + netdev_warn(netdev, "%s: submit rx urb failed: %pe\n",
> + __func__, ERR_PTR(ret));
> +
> + goto error;
...new line, ...
> + }
> +
> + int_urb = usb_alloc_urb(0, GFP_KERNEL);
> + if (!int_urb) {
> + ret = -ENOMEM;
> + goto error;
...no new line.
It would be great to be consistent with a unique style.
> + }
> +
> + int_data = kmalloc(sizeof(*int_data), GFP_KERNEL);
> + if (!int_data) {
> + usb_free_urb(int_urb);
> + ret = -ENOMEM;
> + goto error;
> + }
> +
> + usb_fill_int_urb(int_urb, priv->dev,
> + usb_rcvintpipe(priv->dev, int_in_addr[id]), int_data,
> + sizeof(*int_data), f81604_read_int_callback, netdev,
> + 1);
> +
> + int_urb->transfer_flags |= URB_FREE_BUFFER;
> + usb_anchor_urb(int_urb, &priv->urbs_anchor);
> +
> + ret = usb_submit_urb(int_urb, GFP_KERNEL);
> + if (ret) {
> + usb_unanchor_urb(int_urb);
> + usb_free_urb(int_urb);
> +
> + netdev_warn(netdev, "%s: submit int urb failed: %pe\n",
> + __func__, ERR_PTR(ret));
> + goto error;
> + }
> +
> + /* Drop reference, USB core will take care of freeing it */
> + usb_free_urb(int_urb);
> +
> + return 0;
> +
> +error:
> + f81604_unregister_urbs(priv);
> + return ret;
> +}
> +
> +static int f81604_start(struct net_device *netdev)
> +{
> + struct f81604_port_priv *priv = netdev_priv(netdev);
> + int ret;
> + u8 mode;
> + u8 tmp;
> +
> + mode = F81604_RX_AUTO_RELEASE_BUF | F81604_INT_WHEN_CHANGE;
> +
> + /* Set TR/AT mode */
> + if (priv->can.ctrlmode & CAN_CTRLMODE_ONE_SHOT)
> + mode |= F81604_TX_ONESHOT;
> + else
> + mode |= F81604_TX_NORMAL;
> +
> + ret = f81604_sja1000_write(priv, F81604_CTRL_MODE_REG, mode);
> + if (ret)
> + return ret;
> +
> + /* set reset mode */
> + ret = f81604_set_reset_mode(priv);
> + if (ret)
> + return ret;
> +
> + ret = f81604_chipset_init(priv);
> + if (ret)
> + return ret;
> +
> + /* Clear error counters and error code capture */
> + ret = f81604_sja1000_write(priv, F81604_SJA1000_TXERR, 0);
> + if (ret)
> + return ret;
> +
> + ret = f81604_sja1000_write(priv, F81604_SJA1000_RXERR, 0);
> + if (ret)
> + return ret;
> +
> + /* Read clear for ECC/ALC/IR register */
> + ret = f81604_sja1000_read(priv, F81604_SJA1000_ECC, &tmp);
> + if (ret)
> + return ret;
> +
> + ret = f81604_sja1000_read(priv, F81604_SJA1000_ALC, &tmp);
> + if (ret)
> + return ret;
> +
> + ret = f81604_sja1000_read(priv, F81604_SJA1000_IR, &tmp);
> + if (ret)
> + return ret;
> +
> + ret = f81604_register_urbs(priv);
> + if (ret)
> + return ret;
> +
> + ret = f81604_set_normal_mode(priv);
> + if (ret) {
> + f81604_unregister_urbs(priv);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int f81604_set_bittiming(struct net_device *dev)
> +{
> + struct f81604_port_priv *priv = netdev_priv(dev);
> + struct can_bittiming *bt = &priv->can.bittiming;
> + u8 btr0, btr1;
> + int ret;
> +
> + btr0 = FIELD_PREP(F81604_BRP_MASK, bt->brp - 1) |
> + FIELD_PREP(F81604_SJW_MASK, bt->sjw - 1);
> +
> + btr1 = FIELD_PREP(F81604_SEG1_MASK,
> + bt->prop_seg + bt->phase_seg1 - 1) |
> + FIELD_PREP(F81604_SEG2_MASK, bt->phase_seg2 - 1);
> +
> + if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
> + btr1 |= F81604_SJA1000_BTR1_SAMPLE_TRIPLE;
> +
> + ret = f81604_sja1000_write(priv, F81604_SJA1000_BTR0, btr0);
> + if (ret) {
> + netdev_warn(dev, "%s: Set BTR0 failed: %pe\n", __func__,
> + ERR_PTR(ret));
> + return ret;
> + }
> +
> + ret = f81604_sja1000_write(priv, F81604_SJA1000_BTR1, btr1);
> + if (ret) {
> + netdev_warn(dev, "%s: Set BTR1 failed: %pe\n", __func__,
> + ERR_PTR(ret));
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int f81604_set_mode(struct net_device *netdev, enum can_mode mode)
> +{
> + int ret;
> +
> + switch (mode) {
> + case CAN_MODE_START:
> + ret = f81604_start(netdev);
> + if (!ret && netif_queue_stopped(netdev))
> + netif_wake_queue(netdev);
> + break;
> +
> + default:
> + ret = -EOPNOTSUPP;
> + }
> +
> + return ret;
> +}
> +
> +static void f81604_write_bulk_callback(struct urb *urb)
> +{
> + struct net_device *netdev = urb->context;
> +
> + if (!netif_device_present(netdev))
> + return;
> +
> + if (urb->status)
> + netdev_info(netdev, "%s: Tx URB error: %pe\n", __func__,
> + ERR_PTR(urb->status));
> +}
> +
> +static void f81604_clear_reg_work(struct work_struct *work)
> +{
> + struct f81604_port_priv *priv;
> + u8 tmp;
> +
> + priv = container_of(work, struct f81604_port_priv, clear_reg_work);
> +
> + /* dummy read for clear Arbitration lost capture(ALC) register. */
> + if (test_and_clear_bit(F81604_CLEAR_ALC, &priv->clear_flags))
> + f81604_sja1000_read(priv, F81604_SJA1000_ALC, &tmp);
> +
> + /* dummy read for clear Error code capture(ECC) register. */
> + if (test_and_clear_bit(F81604_CLEAR_ECC, &priv->clear_flags))
> + f81604_sja1000_read(priv, F81604_SJA1000_ECC, &tmp);
> +
> + /* dummy write for clear data overrun flag. */
> + if (test_and_clear_bit(F81604_CLEAR_OVERRUN, &priv->clear_flags))
> + f81604_sja1000_write(priv, F81604_SJA1000_CMR,
> + F81604_SJA1000_CMD_CDO);
> +}
> +
> +static netdev_tx_t f81604_start_xmit(struct sk_buff *skb,
> + struct net_device *netdev)
> +{
> + struct can_frame *cf = (struct can_frame *)skb->data;
> + struct f81604_port_priv *priv = netdev_priv(netdev);
> + struct net_device_stats *stats = &netdev->stats;
> + struct f81604_can_frame *frame;
> + struct urb *write_urb;
> + int ret;
> +
> + if (can_dev_dropped_skb(netdev, skb))
> + return NETDEV_TX_OK;
> +
> + netif_stop_queue(netdev);
> +
> + write_urb = usb_alloc_urb(0, GFP_ATOMIC);
> + if (!write_urb)
> + goto nomem_urb;
> +
> + frame = kzalloc(sizeof(*frame), GFP_ATOMIC);
> + if (!frame)
> + goto nomem_buf;
> +
> + usb_fill_bulk_urb(write_urb, priv->dev,
> + usb_sndbulkpipe(priv->dev,
> + bulk_out_addr[netdev->dev_port]),
> + frame, sizeof(*frame), f81604_write_bulk_callback,
> + priv->netdev);
> +
> + write_urb->transfer_flags |= URB_FREE_BUFFER;
> +
> + frame->cmd = F81604_CMD_DATA;
> + frame->dlc = cf->len;
> +
> + if (cf->can_id & CAN_RTR_FLAG)
> + frame->dlc |= F81604_DLC_RTR_BIT;
> +
> + if (cf->can_id & CAN_EFF_FLAG) {
> + u32 id = (cf->can_id & CAN_EFF_MASK) << F81604_EFF_SHIFT;
> +
> + put_unaligned_be32(id, &frame->eff.id);
> +
> + frame->dlc |= F81604_DLC_EFF_BIT;
> +
> + if (!(cf->can_id & CAN_RTR_FLAG))
> + memcpy(&frame->eff.data, cf->data, cf->len);
> + } else {
> + u32 id = (cf->can_id & CAN_SFF_MASK) << F81604_SFF_SHIFT;
> +
> + put_unaligned_be16(id, &frame->sff.id);
> +
> + if (!(cf->can_id & CAN_RTR_FLAG))
> + memcpy(&frame->sff.data, cf->data, cf->len);
> + }
> +
> + can_put_echo_skb(skb, netdev, 0, 0);
> +
> + ret = usb_submit_urb(write_urb, GFP_ATOMIC);
> + if (ret) {
> + netdev_err(netdev, "%s: failed to resubmit tx bulk urb: %pe\n",
> + __func__, ERR_PTR(ret));
> +
> + can_free_echo_skb(netdev, 0, NULL);
> + stats->tx_dropped++;
> + stats->tx_errors++;
> +
> + if (ret == -ENODEV)
> + netif_device_detach(netdev);
> + else
> + netif_wake_queue(netdev);
> + }
> +
> + /* let usb core take care of this urb */
> + usb_free_urb(write_urb);
> +
> + return NETDEV_TX_OK;
> +
> +nomem_buf:
> + usb_free_urb(write_urb);
> +
> +nomem_urb:
> + dev_kfree_skb(skb);
> + stats->tx_dropped++;
> + stats->tx_errors++;
> + netif_wake_queue(netdev);
> +
> + return NETDEV_TX_OK;
> +}
> +
> +static int f81604_get_berr_counter(const struct net_device *netdev,
> + struct can_berr_counter *bec)
> +{
> + struct f81604_port_priv *priv = netdev_priv(netdev);
> + u8 txerr, rxerr;
> + int ret;
> +
> + ret = f81604_sja1000_read(priv, F81604_SJA1000_TXERR, &txerr);
> + if (ret)
> + return ret;
> +
> + ret = f81604_sja1000_read(priv, F81604_SJA1000_RXERR, &rxerr);
> + if (ret)
> + return ret;
> +
> + bec->txerr = txerr;
> + bec->rxerr = rxerr;
> +
> + return 0;
> +}
> +
> +/* Open USB device */
> +static int f81604_open(struct net_device *netdev)
> +{
> + int ret;
> +
> + ret = open_candev(netdev);
> + if (ret)
> + return ret;
> +
> + ret = f81604_start(netdev);
> + if (ret)
> + goto start_failed;
Here, you have a single goto. You can remove the goto and put the
clean up directly in this if block.
> + netif_start_queue(netdev);
> + return 0;
> +
> +start_failed:
> + if (ret == -ENODEV)
> + netif_device_detach(netdev);
> +
> + close_candev(netdev);
> +
> + return ret;
> +}
> +
> +/* Close USB device */
> +static int f81604_close(struct net_device *netdev)
> +{
> + struct f81604_port_priv *priv = netdev_priv(netdev);
> +
> + f81604_set_reset_mode(priv);
> +
> + netif_stop_queue(netdev);
> + cancel_work_sync(&priv->clear_reg_work);
> + close_candev(netdev);
> +
> + f81604_unregister_urbs(priv);
> +
> + return 0;
> +}
> +
> +static const struct net_device_ops f81604_netdev_ops = {
> + .ndo_open = f81604_open,
> + .ndo_stop = f81604_close,
> + .ndo_start_xmit = f81604_start_xmit,
> + .ndo_change_mtu = can_change_mtu,
> +};
> +
> +static const struct can_bittiming_const f81604_bittiming_const = {
> + .name = KBUILD_MODNAME,
> + .tseg1_min = 1,
> + .tseg1_max = 16,
> + .tseg2_min = 1,
> + .tseg2_max = 8,
> + .sjw_max = 4,
> + .brp_min = 1,
> + .brp_max = 64,
> + .brp_inc = 1,
> +};
> +
> +/* Called by the usb core when driver is unloaded or device is removed */
> +static void f81604_disconnect(struct usb_interface *intf)
> +{
> + struct f81604_priv *priv = usb_get_intfdata(intf);
> + int i;
> +
> + for (i = 0; i < ARRAY_SIZE(priv->netdev); ++i) {
> + if (!priv->netdev[i])
> + continue;
> +
> + unregister_netdev(priv->netdev[i]);
> + free_candev(priv->netdev[i]);
> + }
> +}
> +
> +static int __f81604_set_termination(struct usb_device *dev, int idx, u16 term)
> +{
> + u8 mask, data = 0;
> +
> + if (idx == 0)
> + mask = F81604_CAN0_TERM;
> + else
> + mask = F81604_CAN1_TERM;
> +
> + if (term)
> + data = mask;
> +
> + return f81604_update_bits(dev, F81604_TERMINATOR_REG, mask, data);
> +}
> +
> +static int f81604_set_termination(struct net_device *netdev, u16 term)
> +{
> + struct f81604_port_priv *port_priv = netdev_priv(netdev);
> +
> + ASSERT_RTNL();
> +
> + return __f81604_set_termination(port_priv->dev, netdev->dev_port,
> + term);
> +}
> +
> +static int f81604_probe(struct usb_interface *intf,
> + const struct usb_device_id *id)
> +{
> + struct usb_device *dev = interface_to_usbdev(intf);
> + struct net_device *netdev;
> + struct f81604_priv *priv;
> + int i, ret;
> +
> + priv = devm_kzalloc(&intf->dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + usb_set_intfdata(intf, priv);
> +
> + for (i = 0; i < ARRAY_SIZE(priv->netdev); ++i) {
> + ret = __f81604_set_termination(dev, i, 0);
> + if (ret) {
> + dev_err(&intf->dev,
> + "Setting termination of CH#%d failed: %pe\n",
> + i, ERR_PTR(ret));
> + return ret;
> + }
> + }
> +
> + for (i = 0; i < ARRAY_SIZE(priv->netdev); ++i) {
> + struct f81604_port_priv *port_priv;
> +
> + netdev = alloc_candev(sizeof(*port_priv), 1);
> + if (!netdev) {
> + dev_err(&intf->dev, "Couldn't alloc candev: %d\n", i);
> + ret = -ENOMEM;
> +
> + goto failure_cleanup;
> + }
> +
> + port_priv = netdev_priv(netdev);
> +
> + INIT_WORK(&port_priv->clear_reg_work, f81604_clear_reg_work);
> + init_usb_anchor(&port_priv->urbs_anchor);
> +
> + port_priv->intf = intf;
> + port_priv->dev = dev;
> + port_priv->netdev = netdev;
> + port_priv->can.clock.freq = F81604_CAN_CLOCK;
> +
> + port_priv->can.termination_const = f81604_termination;
> + port_priv->can.termination_const_cnt =
> + ARRAY_SIZE(f81604_termination);
> + port_priv->can.bittiming_const = &f81604_bittiming_const;
> + port_priv->can.do_set_bittiming = f81604_set_bittiming;
> + port_priv->can.do_set_mode = f81604_set_mode;
> + port_priv->can.do_set_termination = f81604_set_termination;
> + port_priv->can.do_get_berr_counter = f81604_get_berr_counter;
> + port_priv->can.ctrlmode_supported =
> + CAN_CTRLMODE_LISTENONLY | CAN_CTRLMODE_3_SAMPLES |
> + CAN_CTRLMODE_ONE_SHOT | CAN_CTRLMODE_BERR_REPORTING |
> + CAN_CTRLMODE_PRESUME_ACK;
> +
> + netdev->ethtool_ops = &f81604_ethtool_ops;
> + netdev->netdev_ops = &f81604_netdev_ops;
> + netdev->flags |= IFF_ECHO;
> + netdev->dev_port = i;
> +
> + SET_NETDEV_DEV(netdev, &intf->dev);
> +
> + ret = register_candev(netdev);
> + if (ret) {
> + netdev_err(netdev, "register CAN device failed: %pe\n",
> + ERR_PTR(ret));
> + free_candev(netdev);
> +
> + goto failure_cleanup;
> + }
> +
> + priv->netdev[i] = netdev;
> + }
> +
> + return 0;
> +
> +failure_cleanup:
> + f81604_disconnect(intf);
> + return ret;
> +}
> +
> +static struct usb_driver f81604_driver = {
> + .name = KBUILD_MODNAME,
> + .probe = f81604_probe,
> + .disconnect = f81604_disconnect,
> + .id_table = f81604_table,
> +};
> +
> +module_usb_driver(f81604_driver);
> +
> +MODULE_AUTHOR("Ji-Ze Hong (Peter Hong) <peter_hong@xxxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("Fintek F81604 USB to 2xCANBUS");
> +MODULE_LICENSE("GPL");
> --
> 2.17.1
>