Re: [PATCH v2 2/2] net: phy: motorcomm: Add pad drive strength cfg support

From: Guo Samin
Date: Fri May 05 2023 - 21:53:03 EST


data: Re: [PATCH v2 2/2] net: phy: motorcomm: Add pad drive strength cfg support
From: Frank Sae <Frank.Sae@xxxxxxxxxxxxxx>
to: Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>, <linux-kernel@xxxxxxxxxxxxxxx>, <devicetree@xxxxxxxxxxxxxxx>, <netdev@xxxxxxxxxxxxxxx>, Peter Geis <pgwipeout@xxxxxxxxx>
data: 2023/5/6

>
>
> On 2023/5/5 17:05, Samin Guo wrote:
>> The motorcomm phy (YT8531) supports the ability to adjust the drive
>> strength of the rx_clk/rx_data, and the default strength may not be
>> suitable for all boards. So add configurable options to better match
>> the boards.(e.g. StarFive VisionFive 2)
>>
>> Signed-off-by: Samin Guo <samin.guo@xxxxxxxxxxxxxxxx>
>> ---
>> drivers/net/phy/motorcomm.c | 46 +++++++++++++++++++++++++++++++++++++
>> 1 file changed, 46 insertions(+)
>>
>> diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
>> index 2fa5a90e073b..191650bb1454 100644
>> --- a/drivers/net/phy/motorcomm.c
>> +++ b/drivers/net/phy/motorcomm.c
>> @@ -236,6 +236,7 @@
>> */
>> #define YTPHY_WCR_TYPE_PULSE BIT(0)
>>
>> +#define YTPHY_PAD_DRIVE_STRENGTH_REG 0xA010
>> #define YTPHY_SYNCE_CFG_REG 0xA012
>> #define YT8521_SCR_SYNCE_ENABLE BIT(5)
>> /* 1b0 output 25m clock
>> @@ -260,6 +261,14 @@
>> #define YT8531_SCR_CLK_SRC_REF_25M 4
>> #define YT8531_SCR_CLK_SRC_SSC_25M 5
>>
>> +#define YT8531_RGMII_RXC_DS_DEFAULT 0x3
>> +#define YT8531_RGMII_RXC_DS_MAX 0x7
>> +#define YT8531_RGMII_RXC_DS GENMASK(15, 13)
>> +#define YT8531_RGMII_RXD_DS_DEFAULT 0x3
>> +#define YT8531_RGMII_RXD_DS_MAX 0x7
>> +#define YT8531_RGMII_RXD_DS_LOW GENMASK(5, 4) /* Bit 1/0 of rxd_ds */
>> +#define YT8531_RGMII_RXD_DS_HI BIT(12) /* Bit 2 of rxd_ds */
>
>
> YT8531_RGMII_xxx is bit define for YTPHY_PAD_DRIVE_STRENGTH_REG, so it is better to put it under the define of YTPHY_PAD_DRIVE_STRENGTH_REG.
>
> YT8531_RGMII_xxx bit define as reverse order:
> #define YTPHY_PAD_DRIVE_STRENGTH_REG 0xA010
> #define YT8531_RGMII_RXC_DS GENMASK(15, 13)
> #define YT8531_RGMII_RXD_DS_HI BIT(12) /* Bit 2 of rxd_ds */ <-------
> #define YT8531_RGMII_RXD_DS_LOW GENMASK(5, 4) /* Bit 1/0 of rxd_ds */
> ...
>
Hi Frank,

Ok, will fix it next version.
btw, do you have any information you can provide about Andrew's mention of using real unit uA/mA instead of magic numbers?
(I couldn't find any information about current in the YT8531's datasheet other than the magic numbers.)


Below is all the relevant information I found:

Pad Drive Strength Cfg (EXT_0xA010)

Bit | Symbol | Access | Default | Description
15:13 | Rgmii_sw_dr_rx | RW | 0x3 | Drive strenght of rx_clk pad.
| 3'b111: strongest; 3'b000: weakest.

12 | Rgmii_sw_dr[2] | RW | 0x0 | Bit 2 of Rgmii_sw_dr[2:0], refer to ext A010[5:4]

5:4 | Rgmii_sw_dr[1:0] | RW | 0x3 | Bit 1 and 0 of Rgmii_sw_dr, Drive strenght of rxd/rx_ctl rgmii pad.
| 3'b111: strongest; 3'b000: weakest


Best regards,
Samin

>> +
>> /* Extended Register end */
>>
>> #define YTPHY_DTS_OUTPUT_CLK_DIS 0
>> @@ -1495,6 +1504,7 @@ static int yt8531_config_init(struct phy_device *phydev)
>> {
>> struct device_node *node = phydev->mdio.dev.of_node;
>> int ret;
>> + u32 ds, val;
>>
>> ret = ytphy_rgmii_clk_delay_config_with_lock(phydev);
>> if (ret < 0)
>> @@ -1518,6 +1528,42 @@ static int yt8531_config_init(struct phy_device *phydev)
>> return ret;
>> }
>>
>> + ds = YT8531_RGMII_RXC_DS_DEFAULT;
>> + if (!of_property_read_u32(node, "motorcomm,rx-clk-driver-strength", &val)) {
>> + if (val > YT8531_RGMII_RXC_DS_MAX)
>> + return -EINVAL;
>> +
>> + ds = val;
>> + }
>> +
>> + ret = ytphy_modify_ext_with_lock(phydev,
>> + YTPHY_PAD_DRIVE_STRENGTH_REG,
>> + YT8531_RGMII_RXC_DS,
>> + FIELD_PREP(YT8531_RGMII_RXC_DS, ds));
>> + if (ret < 0)
>> + return ret;
>> +
>> + ds = FIELD_PREP(YT8531_RGMII_RXD_DS_LOW, YT8531_RGMII_RXD_DS_DEFAULT);
>> + if (!of_property_read_u32(node, "motorcomm,rx-data-driver-strength", &val)) {
>> + if (val > YT8531_RGMII_RXD_DS_MAX)
>> + return -EINVAL;
>> +
>> + if (val > FIELD_MAX(YT8531_RGMII_RXD_DS_LOW)) {
>> + ds = val & FIELD_MAX(YT8531_RGMII_RXD_DS_LOW);
>> + ds = FIELD_PREP(YT8531_RGMII_RXD_DS_LOW, ds);
>> + ds |= YT8531_RGMII_RXD_DS_HI;
>> + } else {
>> + ds = FIELD_PREP(YT8531_RGMII_RXD_DS_LOW, val);
>> + }
>> + }
>> +
>> + ret = ytphy_modify_ext_with_lock(phydev,
>> + YTPHY_PAD_DRIVE_STRENGTH_REG,
>> + YT8531_RGMII_RXD_DS_LOW | YT8531_RGMII_RXD_DS_HI,
>> + ds);
>> + if (ret < 0)
>> + return ret;
>> +
>> return 0;
>> }
>>