Re: [PATCH v2 5/7] dt-bindings: sound: Add support for the Lantiq PEF2256 codec

[Krzysztof Kozlowski]

On 16/03/2023 13:27, Herve Codina wrote:
> The Lantiq PEF2256, also known as Infineon PEF2256 or FALC256, is a
> framer and line interface component designed to fulfill all required
> interfacing between an analog E1/T1/J1 line and the digital PCM system
> highway/H.100 bus.
> 
> The codec support allows to use some of the PCM system highway
> time-slots as audio channels to transport audio data over the E1/T1/J1
> lines.
> 

Your other file should also have specific compatible, unless this codec
is actually part of the framer. Did not look like this in the binding -
not $ref.

> Signed-off-by: Herve Codina <herve.codina@xxxxxxxxxxx>
> ---
>  .../bindings/sound/lantiq,pef2256-codec.yaml  | 57 +++++++++++++++++++
>  1 file changed, 57 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/sound/lantiq,pef2256-codec.yaml
> 
> diff --git a/Documentation/devicetree/bindings/sound/lantiq,pef2256-codec.yaml b/Documentation/devicetree/bindings/sound/lantiq,pef2256-codec.yaml
> new file mode 100644
> index 000000000000..acba3a0ccd1b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/sound/lantiq,pef2256-codec.yaml
> @@ -0,0 +1,57 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/sound/lantiq,pef2256-codec.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Lantiq PEF2256 codec device

Drop "device". Everything is "device".

> +
> +maintainers:
> +  - Herve Codina <herve.codina@xxxxxxxxxxx>
> +
> +description: |
> +  Codec support for PEF2256.
> +
> +  The Lantiq PEF2256, also known as Infineon PEF2256 or FALC256, is a framer and
> +  line interface component designed to fulfill all required interfacing between
> +  an analog E1/T1/J1 line and the digital PCM system highway/H.100 bus.
> +
> +  The codec support allows to use some of the PCM system highway time-slots as
> +  audio channels to transport audio data over the E1/T1/J1 lines.
> +
> +  The time-slots used by the codec must be set and so, the properties
> +  'dai-tdm-slot-num', 'dai-tdm-slot-width', 'dai-tdm-slot-tx-mask' and
> +  'dai-tdm-slot-rx-mask' must be present in the ALSA sound card node for
> +  sub-nodes that involve the codec. The codec uses 8bit time-slots.
> +  'dai-tdm-tdm-slot-with' must be set to 8.
> +
> +allOf:
> +  - $ref: /schemas/spi/spi-peripheral-props.yaml#
> +  - $ref: dai-common.yaml#
> +
> +properties:
> +  compatible:
> +    const: lantiq,pef2256-codec
> +
> +  lantiq,pef2256:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description:
> +      phandle to the PEF2256

Why not its child? Why this is in parallel ?

> +
> +  '#sound-dai-cells':
> +    const: 0
> +


Best regards,
Krzysztof