Re: [PATCH] staging: axis-fifo: initialize timeouts in probe only

[Khadija Kamran]

On Wed, Mar 15, 2023 at 05:44:47PM +0100, Fabio M. De Francesco wrote:
> On mercoledì 15 marzo 2023 14:56:27 CET Khadija Kamran wrote:
> > On Wed, Mar 15, 2023 at 02:13:51PM +0100, Fabio M. De Francesco wrote:
> > > On mercoledì 15 marzo 2023 13:32:55 CET Khadija Kamran wrote:
> > > > On Tue, Mar 14, 2023 at 04:57:47PM -0700, Alison Schofield wrote:
> > > > > My guess is that this patch gets ignored because it has a lower 
> version
> > > > > number than a previous patch.
> > > > > 
> > > > > Take the feedback given here, and rev to
> > > > > [PATCH v5] staging: axis-fifo: initialize timeouts in probe only
> > > > > 
> > > > > Be sure the Changelog, below the --- explains the journey.
> > > > > 
> > > > > Changes in v5:
> > > > > 
> > > > > Changes in v4:
> > > > > 
> > > > > Changes in v3:
> > > > 
> > > > > Changes in v2:
> > > > Hey Alison!
> > > 
> > > Hi Khadija,
> > > 
> > > Please put one or two blank lines between the last message you are 
> replying
> > > and the new you are writing (exactly as I'm doing here between "Hey 
> Alison!"
> > > and "Hi Khadija").
> > 
> > Hey Fabio!
> > 
> > Sorry about that. This was pointed by Alison before and I have been
> > adding spaces since then. Hopefully I am doing it right this time.
> > 
> You are doing right this time :-)
> >
> > > > Based on Nathan's feedback I am trying to recompile and send a patch
> > > > without any warnings.
> > > 
> > > Great!
> > > 
> > > > As suggested by Fabio, I am running "make w=1 -jX" command to see if I
> > > > get any warnings.
> > > 
> > > I suppose that "w=1" is a typo. The option is enabled with "W=1" (capital
> > > case, Linux and all UNIX-like are case-sensitive).
> > 
> > Okay. I should re-run it with "W=1".
> > 
> > > > But it is taking a lot of time, is there any way of
> > > > speeding it up?
> > > 
> > > What is you choice for 'X' in "-jX"?
> > 
> > I used "-j4".
> > 
> > > Did you try with the exact number of logical cores?
> > > Are you building into a VM with enough logical cores?
> > > If you are building into a VM, did you reserve enough RAM?
> > 
> > I am using Ubuntu 22.04.01 with the help of VM on VMware.
> > My machine has 13GB RAM and 2 processors(4 cores each).
> 
> Therefore, you are using a Linux guest on a Linux host. This is a wise choice. 
> However, you didn't say where you are running your builds...

Hey Fabio!

I am not using a Linux guest on Linux host. Sorry if I did not explain
it right. I am using Windows 10 and in order to run Ubuntu, I have
created a VM(on VMWare). This VM has 13GB RAM and 2 processors(4 cores
each).
Thank you!

Regards,
Khadija
> 
> I mean, the better things to do are the following steps:
> 
> 1) Your workspace with the staging tree should stay in the host.
> 2) Shut down your guest in order to have all RAM and all logical processors 
> available for the build.
> 3) Run "make -j8" in the host. Since you shutdown your guest VM you can use 
> all 8 logical cores and the maximum available RAM (without the VM draining 
> resources while building)
> 4) When the build is done, switch on your VM on VMware with at least 4 logical 
> cores and 6GB of reserved RAM.
> 5) Mount your cloned base directory as a shared folder between host and guest.
> 6) In the guest, 'cd' to the shared folder and then run "make modules_install 
> install" (in the guest, attention). This will install and configure the 
> kernel, the modules, GRUB2 and everything else in your guest VM.
> 7) Reboot the VM and test your patches.
> 
> This procedure will speed up your next builds.
> The fundamental point is that you don't need to partition precious resources 
> while building, Do everything without running the VM and switch it on only for 
> install and tests. Since you only build in the host but never install and boot 
> in it, you don't risk any system's damage.
> 
> This is what I do for Kernel development purposes.
> 
> I hope it helps to answer your question about how to run fast recompilation.
> 
> Fabio  
> 
> 
> > 
> > > Please read carefully my questions above and try to understand your
> > > environment and reply, so that I can help you more effectively.
> > > 
> > > > If this doesn't work then I have to follow the steps to reproduce in lkp
> > > > mail as you said before.
> > > 
> > > The steps to reproduce will take your precious time and use more 
> resources.
> > > Again, try to respond my questions.
> > > 
> > > > After dealing with these warnings I will send a [PATCH v5], following
> > > > your instructions above.
> > > 
> > > Sorry for inadvertently overlooking to warn you about to send a message to
> > > Greg and ask him to drop your first 3 + 1 patches. Now you are doing good 
> by
> > > following what Alison suggested: send v5 and write the log of revisions
> > > under
> > > the three dashes (exactly how Alison explained).
> > > 
> > > > Kindly, let me know if I am on the wrong track.
> > > > Thank you!
> > > 
> > > I think you are in the right track.
> > > Let's try to speed up your builds because you'll need to build again your
> > > kernel many, many times for future works.
> > 
> > Okay great! Thank you.
> > 
> > Regards,
> > Khadija
> > 
> > > Thanks,
> > > 
> > > Fabio
> 
> 
> 
>