Re: [PATCH 2/2] hwmon: (adt7475) Fix setting of hysteresis registers

From: Tony O'Brien
Date: Thu Feb 23 2023 - 16:57:48 EST


On 22/02/23 06:15, Guenter Roeck wrote:
> On 2/20/23 06:08, Guenter Roeck wrote:
>> On Mon, Feb 20, 2023 at 12:29:56PM +1300, Tony O'Brien wrote:
>>> In temp_store(), for the hysteresis setting calculation there were two
>>> errors.  The first tries to clamp the hysteresis value by comparing the
>>> required hysteresis value to THERM - 15C.  This is incorrect since the
>>> hysteresis value is a relative value whereas THERM - 15C is an absolute
>>
>> No, it isn't. The hysteresis attribute is an absolute temperature.
>> The value written into the attribute is expected to be in the range
>> [THERM - 15, THERM] (in degrees C). The value written into the register
>> is then in the range [15, 0]. I see nothing wrong with the current code.
>>
>>> value. This causes it to always select 15C for hysteresis.  Change the
>>> first parameter to THERM - val to compare two absolute temperatures.
>>> The second error masks the wrong bits in the hysteresis register;
>>> indices
>>> 0 and 2 should zero bits [7:4] and preserve bits [3:0], and index 1
>>> should
>>> zero bits [3:0] and preserve bits [7:4].
>>
>> I'll have to verify that with the datasheet. Either case, one logical
>> change
>> per patch, please.
>>
>
> Actually, the problem is obvious from the code. Still, either drop the
> first
> part of the patch or separate into two patches and explain in detail what
> you think is wrong in the first part. There is a comment in the code
>
>                 /*
>                  * The value will be given as an absolute value, turn it
>                  * into an offset based on THERM
>                  */
>
> Maybe I am missing something, but I think that is exactly what the current
> code is doing.
Sorry for the late reply, my email wasn't working properly.

You are correct, and so is the code. I assumed the hysteresis would be
written to the sysfs temp#_crit_hyst file as a relative temperature,
(being called 'hyst') not an absolute value. I have fixed our host code
to write this correctly and it works fine now. This part of the patch
has been dropped and v2 has been sent. Thanks for your help.

Cheers,
Tony.
>
> Thanks,
> Guenter
>
>> Thanks,
>> Guenter
>>
>>>
>>> Fixes: 1c301fc5394f ("hwmon: Add a driver for the ADT7475 hardware
>>> monitoring chip")
>>> Signed-off-by: Tony O'Brien <tony.obrien@xxxxxxxxxxxxxxxxxxx>
>>> ---
>>>   drivers/hwmon/adt7475.c | 6 +++---
>>>   1 file changed, 3 insertions(+), 3 deletions(-)
>>>
>>> diff --git a/drivers/hwmon/adt7475.c b/drivers/hwmon/adt7475.c
>>> index 77222c35a38e..68233191798e 100644
>>> --- a/drivers/hwmon/adt7475.c
>>> +++ b/drivers/hwmon/adt7475.c
>>> @@ -484,14 +484,14 @@ static ssize_t temp_store(struct device *dev,
>>> struct device_attribute *attr,
>>>           adt7475_read_hystersis(client);
>>>           temp = reg2temp(data, data->temp[THERM][sattr->index]);
>>> -        val = clamp_val(val, temp - 15000, temp);
>>> +        val = clamp_val(temp - val, temp - 15000, temp);
>>>           val = (temp - val) / 1000;
>>>           if (sattr->index != 1) {
>>> -            data->temp[HYSTERSIS][sattr->index] &= 0xF0;
>>> +            data->temp[HYSTERSIS][sattr->index] &= 0x0F;
>>>               data->temp[HYSTERSIS][sattr->index] |= (val & 0xF) << 4;
>>>           } else {
>>> -            data->temp[HYSTERSIS][sattr->index] &= 0x0F;
>>> +            data->temp[HYSTERSIS][sattr->index] &= 0xF0;
>>>               data->temp[HYSTERSIS][sattr->index] |= (val & 0xF);
>>>           }
>>> --
>>> 2.39.2
>>>
>