Re: [PATCH v3 00/14] media: rkisp1: Add support for i.MX8MP

From: Adam Ford
Date: Thu Feb 23 2023 - 11:10:43 EST


On Thu, Feb 23, 2023 at 8:26 AM Laurent Pinchart
<laurent.pinchart@xxxxxxxxxxxxxxxx> wrote:
>
> Hi Adam,
>
> On Wed, Feb 22, 2023 at 05:39:30PM -0600, Adam Ford wrote:
> > On Fri, Nov 18, 2022 at 3:44 AM Paul Elder wrote:
> > >
> > > This series depends on v3 of "dt-bindings: media: Add macros for video
> > > interface bus types" [1].
> > >
> > > This series extends the rkisp1 driver to support the ISP found in the
> > > NXP i.MX8MP SoC.
> > >
> > > The ISP IP cores in the Rockchip RK3399 (known as the "Rockchip ISP1")
> > > and in the NXP i.MX8MP have the same origin, and have slightly diverged
> > > over time as they are now independently developed (afaik) by Rockchip
> > > and VeriSilicon. The latter is marketed under the name "ISP8000Nano",
> > > and is close enough to the RK3399 ISP that it can easily be supported by
> > > the same driver.
> > >
> > > The last two patches add support for UYVY output format, which can be
> > > implemented on the ISP version in the i.MX8MP but not in the one in the
> > > RK3399.
> > >
> > > This version of the series specifically has been tested on a Polyhex
> > > Debix model A with an imx219 (Raspberry Pi cam v2).
> > >
> > > [1] https://lore.kernel.org/linux-media/20220615221410.27459-2-laurent.pinchart@xxxxxxxxxxxxxxxx/
> > >
> > > Laurent Pinchart (3):
> > > dt-bindings: media: rkisp1: Add i.MX8MP ISP example
> > > media: rkisp1: Add and use rkisp1_has_feature() macro
> > > media: rkisp1: Configure gasket on i.MX8MP
> > >
> > > Paul Elder (11):
> > > dt-bindings: media: rkisp1: Add i.MX8MP ISP to compatible
> > > media: rkisp1: Add match data for i.MX8MP ISP
> > > media: rkisp1: Add and set registers for crop for i.MX8MP
> > > media: rkisp1: Add and set registers for output size config on i.MX8MP
> > > media: rkisp1: Add i.MX8MP-specific registers for MI and resizer
> > > media: rkisp1: Shift DMA buffer addresses on i.MX8MP
> > > media: rkisp1: Add register definitions for the test pattern generator
> > > media: rkisp1: Fix RSZ_CTRL bits for i.MX8MP
> > > media: rkisp1: Support devices without self path
> > > media: rkisp1: Add YC swap capability
> > > media: rkisp1: Add UYVY as an output format
> >
> > Paul / Laurent,
> >
> > I noticed an unexpected behaviour on the imx8mp.
> >
> > If I setup my pipeline for 640x480, it works just fine using an imx219
> > camera configured for SRGGB10_1X10.
> >
> > However, when I try to configure the pipeline to use the same camera
> > at 1920x1080 (no resizing), the ISP source keeps defaulting to 640x480
> >
> > Media device information
> > ------------------------
> > driver rkisp1
> > model rkisp1
> > serial
> > bus info platform:rkisp1
> > hw revision 0xe
> > driver version 6.2.0
> >
> > Device topology
> > - entity 1: rkisp1_isp (4 pads, 4 links)
> > type V4L2 subdev subtype Unknown flags 0
> > device node name /dev/v4l-subdev0
> > pad0: Sink [fmt:SRGGB10_1X10/1920x1080 field:none colorspace:raw xfer:none ycbcr:601 quantization:full-range crop.bounds:(0,0)/1920x1080 crop:(0,0)/640x480]
>
> You're cropping the image to 640x480 here. You need to set the crop
> rectangle to 1920x1080.
>
> As Jacopo mentioned, I wouldn't recommend exercising the ISP directly.
> Not only do you need to setup the pipeline, but you would also need to
> implement all the imaging algorithms in userspace. libcamera will do all
> this for you.

I'll give that a try. My current employer has a v4l2src requirement,
but I can likely make an argument to switch to libcamera. I didn't
catch the cropping part. Thanks for that.

adam
>
> > <- "csis-32e40000.csi":1 [ENABLED]
> > pad1: Sink [fmt:unknown/0x0 field:none]
> > <- "rkisp1_params":0 [ENABLED,IMMUTABLE]
> > pad2: Source [fmt:YUYV8_2X8/640x480 field:none colorspace:raw xfer:none ycbcr:601 quantization:lim-range crop.bounds:(0,0)/640x480 crop:(0,0)/640x480]
> > -> "rkisp1_resizer_mainpath":0 [ENABLED]
> > pad3: Source [fmt:unknown/0x0 field:none]
> > -> "rkisp1_stats":0 [ENABLED,IMMUTABLE]
> >
> > - entity 6: rkisp1_resizer_mainpath (2 pads, 2 links)
> > type V4L2 subdev subtype Unknown flags 0
> > device node name /dev/v4l-subdev1
> > pad0: Sink [fmt:YUYV8_2X8/1920x1080 field:none colorspace:srgb xfer:srgb ycbcr:601 quantization:lim-range crop.bounds:(0,0)/1920x1080 crop:(0,0)/640x480]
> > <- "rkisp1_isp":2 [ENABLED]
> > pad1: Source [fmt:YUYV8_2X8/1920x1080 field:none colorspace:srgb xfer:srgb ycbcr:601 quantization:lim-range]
> > -> "rkisp1_mainpath":0 [ENABLED,IMMUTABLE]
> >
> > - entity 9: rkisp1_mainpath (1 pad, 1 link)
> > type Node subtype V4L flags 0
> > device node name /dev/video0
> > pad0: Sink
> > <- "rkisp1_resizer_mainpath":1 [ENABLED,IMMUTABLE]
> >
> > - entity 13: rkisp1_stats (1 pad, 1 link)
> > type Node subtype V4L flags 0
> > device node name /dev/video1
> > pad0: Sink
> > <- "rkisp1_isp":3 [ENABLED,IMMUTABLE]
> >
> > - entity 17: rkisp1_params (1 pad, 1 link)
> > type Node subtype V4L flags 0
> > device node name /dev/video2
> > pad0: Source
> > -> "rkisp1_isp":1 [ENABLED,IMMUTABLE]
> >
> > - entity 29: csis-32e40000.csi (2 pads, 2 links)
> > type V4L2 subdev subtype Unknown flags 0
> > device node name /dev/v4l-subdev2
> > pad0: Sink [fmt:SRGGB10_1X10/1920x1080 field:none colorspace:srgb xfer:srgb ycbcr:601 quantization:full-range]
> > <- "imx219 1-0010":0 [ENABLED]
> > pad1: Source [fmt:SRGGB10_1X10/1920x1080 field:none colorspace:srgb xfer:srgb ycbcr:601 quantization:full-range]
> > -> "rkisp1_isp":0 [ENABLED]
> >
> > - entity 34: imx219 1-0010 (1 pad, 1 link)
> > type V4L2 subdev subtype Sensor flags 0
> > device node name /dev/v4l-subdev3
> > pad0: Source [fmt:SRGGB10_1X10/1920x1080 field:none colorspace:srgb xfer:srgb ycbcr:601 quantization:full-range crop.bounds:(8,8)/3280x2464 crop:(688,700)/1920x1080]
> > -> "csis-32e40000.csi":0 [ENABLED]
> >
> > It's at this point that everything except the ISP source is 1920x1080.
> >
> > When I try to set the ISP sink to 1080, it ends up being 640x480 and
> > the resizer sink is also changed to 640x480
> >
> > root@beacon-imx8mp-kit:~# media-ctl -v -V "'rkisp1_isp':2
> > [fmt:YUYV8_2X8/1920x1080 field:none]"
> > Opening media device /dev/media0
> > Enumerating entities
> > looking up device: 81:3
> > looking up device: 81:4
> > looking up device: 81:0
> > looking up device: 81:1
> > looking up device: 81:2
> > looking up device: 81:5
> > looking up device: 81:6
> > Found 7 entities
> > Enumerating pads and links
> > Setting up format YUYV8_2X8 1920x1080 on pad rkisp1_isp/2
> > Format set: YUYV8_2X8 640x480
> > Setting up format YUYV8_2X8 640x480 on pad rkisp1_resizer_mainpath/0
> > Format set: YUYV8_2X8 640x480
> >
> >
> > It's my understanding that the ISP should be able to handle 1920x1080,
> > and the resizer sink should match the ISP source.
> >
> > With the pipeline improperly setup, the capture fails.
> >
> > > .../bindings/media/rockchip-isp1.yaml | 79 ++++++++++-
> > > .../platform/rockchip/rkisp1/rkisp1-capture.c | 102 +++++++++++---
> > > .../platform/rockchip/rkisp1/rkisp1-common.h | 32 +++++
> > > .../platform/rockchip/rkisp1/rkisp1-debug.c | 14 +-
> > > .../platform/rockchip/rkisp1/rkisp1-dev.c | 67 +++++++--
> > > .../platform/rockchip/rkisp1/rkisp1-isp.c | 128 +++++++++++++++++-
> > > .../platform/rockchip/rkisp1/rkisp1-regs.h | 90 ++++++++++++
> > > .../platform/rockchip/rkisp1/rkisp1-resizer.c | 35 ++++-
> > > include/uapi/linux/rkisp1-config.h | 2 +
> > > 9 files changed, 509 insertions(+), 40 deletions(-)
>
> --
> Regards,
>
> Laurent Pinchart