Re: [PATCH v3 00/14] media: rkisp1: Add support for i.MX8MP

From: Jacopo Mondi
Date: Thu Feb 23 2023 - 08:58:20 EST


Hi Adam

On Wed, Feb 22, 2023 at 05:39:30PM -0600, Adam Ford wrote:
> On Fri, Nov 18, 2022 at 3:44 AM Paul Elder <paul.elder@xxxxxxxxxxxxxxxx> wrote:
> >
> > This series depends on v3 of "dt-bindings: media: Add macros for video
> > interface bus types" [1].
> >
> > This series extends the rkisp1 driver to support the ISP found in the
> > NXP i.MX8MP SoC.
> >
> > The ISP IP cores in the Rockchip RK3399 (known as the "Rockchip ISP1")
> > and in the NXP i.MX8MP have the same origin, and have slightly diverged
> > over time as they are now independently developed (afaik) by Rockchip
> > and VeriSilicon. The latter is marketed under the name "ISP8000Nano",
> > and is close enough to the RK3399 ISP that it can easily be supported by
> > the same driver.
> >
> > The last two patches add support for UYVY output format, which can be
> > implemented on the ISP version in the i.MX8MP but not in the one in the
> > RK3399.
> >
> > This version of the series specifically has been tested on a Polyhex
> > Debix model A with an imx219 (Raspberry Pi cam v2).
> >
> > [1] https://lore.kernel.org/linux-media/20220615221410.27459-2-laurent.pinchart@xxxxxxxxxxxxxxxx/
> >
> > Laurent Pinchart (3):
> > dt-bindings: media: rkisp1: Add i.MX8MP ISP example
> > media: rkisp1: Add and use rkisp1_has_feature() macro
> > media: rkisp1: Configure gasket on i.MX8MP
> >
> > Paul Elder (11):
> > dt-bindings: media: rkisp1: Add i.MX8MP ISP to compatible
> > media: rkisp1: Add match data for i.MX8MP ISP
> > media: rkisp1: Add and set registers for crop for i.MX8MP
> > media: rkisp1: Add and set registers for output size config on i.MX8MP
> > media: rkisp1: Add i.MX8MP-specific registers for MI and resizer
> > media: rkisp1: Shift DMA buffer addresses on i.MX8MP
> > media: rkisp1: Add register definitions for the test pattern generator
> > media: rkisp1: Fix RSZ_CTRL bits for i.MX8MP
> > media: rkisp1: Support devices without self path
> > media: rkisp1: Add YC swap capability
> > media: rkisp1: Add UYVY as an output format
> >
>
> Paul / Laurent,
>
> I noticed an unexpected behaviour on the imx8mp.
>
> If I setup my pipeline for 640x480, it works just fine using an imx219
> camera configured for SRGGB10_1X10.
>
> However, when I try to configure the pipeline to use the same camera
> at 1920x1080 (no resizing), the ISP source keeps defaulting to 640x480
>
> Media device information
> ------------------------
> driver rkisp1
> model rkisp1
> serial
> bus info platform:rkisp1
> hw revision 0xe
> driver version 6.2.0
>
> Device topology
> - entity 1: rkisp1_isp (4 pads, 4 links)
> type V4L2 subdev subtype Unknown flags 0
> device node name /dev/v4l-subdev0
> pad0: Sink
> [fmt:SRGGB10_1X10/1920x1080 field:none colorspace:raw xfer:none
> ycbcr:601 quantization:full-range
> crop.bounds:(0,0)/1920x1080
> crop:(0,0)/640x480]
> <- "csis-32e40000.csi":1 [ENABLED]
> pad1: Sink
> [fmt:unknown/0x0 field:none]
> <- "rkisp1_params":0 [ENABLED,IMMUTABLE]
> pad2: Source
> [fmt:YUYV8_2X8/640x480 field:none colorspace:raw xfer:none ycbcr:601
> quantization:lim-range
> crop.bounds:(0,0)/640x480
> crop:(0,0)/640x480]
> -> "rkisp1_resizer_mainpath":0 [ENABLED]
> pad3: Source
> [fmt:unknown/0x0 field:none]
> -> "rkisp1_stats":0 [ENABLED,IMMUTABLE]
>
> - entity 6: rkisp1_resizer_mainpath (2 pads, 2 links)
> type V4L2 subdev subtype Unknown flags 0
> device node name /dev/v4l-subdev1
> pad0: Sink
> [fmt:YUYV8_2X8/1920x1080 field:none colorspace:srgb xfer:srgb
> ycbcr:601 quantization:lim-range
> crop.bounds:(0,0)/1920x1080
> crop:(0,0)/640x480]
> <- "rkisp1_isp":2 [ENABLED]
> pad1: Source
> [fmt:YUYV8_2X8/1920x1080 field:none colorspace:srgb xfer:srgb
> ycbcr:601 quantization:lim-range]
> -> "rkisp1_mainpath":0 [ENABLED,IMMUTABLE]
>
> - entity 9: rkisp1_mainpath (1 pad, 1 link)
> type Node subtype V4L flags 0
> device node name /dev/video0
> pad0: Sink
> <- "rkisp1_resizer_mainpath":1 [ENABLED,IMMUTABLE]
>
> - entity 13: rkisp1_stats (1 pad, 1 link)
> type Node subtype V4L flags 0
> device node name /dev/video1
> pad0: Sink
> <- "rkisp1_isp":3 [ENABLED,IMMUTABLE]
>
> - entity 17: rkisp1_params (1 pad, 1 link)
> type Node subtype V4L flags 0
> device node name /dev/video2
> pad0: Source
> -> "rkisp1_isp":1 [ENABLED,IMMUTABLE]
>
> - entity 29: csis-32e40000.csi (2 pads, 2 links)
> type V4L2 subdev subtype Unknown flags 0
> device node name /dev/v4l-subdev2
> pad0: Sink
> [fmt:SRGGB10_1X10/1920x1080 field:none colorspace:srgb xfer:srgb
> ycbcr:601 quantization:full-range]
> <- "imx219 1-0010":0 [ENABLED]
> pad1: Source
> [fmt:SRGGB10_1X10/1920x1080 field:none colorspace:srgb xfer:srgb
> ycbcr:601 quantization:full-range]
> -> "rkisp1_isp":0 [ENABLED]
>
> - entity 34: imx219 1-0010 (1 pad, 1 link)
> type V4L2 subdev subtype Sensor flags 0
> device node name /dev/v4l-subdev3
> pad0: Source
> [fmt:SRGGB10_1X10/1920x1080 field:none colorspace:srgb xfer:srgb
> ycbcr:601 quantization:full-range
> crop.bounds:(8,8)/3280x2464
> crop:(688,700)/1920x1080]
> -> "csis-32e40000.csi":0 [ENABLED]

Not sure if it's my email reader but I'm sorry I can't read this.
Could you use an online paste service next time if lines are long and
gets wrapped in this way ?

>
> It's at this point that everything except the ISP source is 1920x1080.
>
> When I try to set the ISP sink to 1080, it ends up being 640x480 and
> the resizer sink is also changed to 640x480
>
> root@beacon-imx8mp-kit:~# media-ctl -v -V "'rkisp1_isp':2
> [fmt:YUYV8_2X8/1920x1080 field:none]"
> Opening media device /dev/media0
> Enumerating entities
> looking up device: 81:3
> looking up device: 81:4
> looking up device: 81:0
> looking up device: 81:1
> looking up device: 81:2
> looking up device: 81:5
> looking up device: 81:6
> Found 7 entities
> Enumerating pads and links
> Setting up format YUYV8_2X8 1920x1080 on pad rkisp1_isp/2
> Format set: YUYV8_2X8 640x480
> Setting up format YUYV8_2X8 640x480 on pad rkisp1_resizer_mainpath/0
> Format set: YUYV8_2X8 640x480
>

I'm on https://gitlab.com/ideasonboard/nxp/linux/-/tree/v6.2/merge
with an additional patch to enable the ISP on the board I'm testing
with

I've tested capturing YUYV 1920x1080 with the following script

------------------------------------------------------------------------------
#!/bin/bash -x

media-ctl -r

# Link entities
media-ctl -l '"ar0521 1-0036":0 -> "csis-32e40000.csi":0'[1]
media-ctl -l '"csis-32e40000.csi":1 -> "rkisp1_isp":0'[1]
media-ctl -l '"rkisp1_isp":2 -> "rkisp1_resizer_mainpath":0'[1]

# Setup format
media-ctl -v -V '"ar0521 1-0036":0 [fmt:SGRBG8_1X8/2592x1944]'
media-ctl -v -V '"csis-32e40000.csi":1 [fmt:SGRBG8_1X8/2592x1944]'
media-ctl -v -V '"rkisp1_isp":2 [fmt:YUYV8_2X8/2592x1944]'
media-ctl -v -V '"rkisp1_resizer_mainpath":1 [fmt:YUYV8_2X8/1920x1080]'

yavta -f YUYV -s 1920x1080 -c10 /dev/video0 --file=/tmp/frame-#.bin
------------------------------------------------------------------------------

You will have to adjust it for imx219

Unless you tweak the sensor's exposure and gains manually do not
expect nice images. You would need an auto-exposure and gain routine
like the one implemented in libcamera.

>
> It's my understanding that the ISP should be able to handle 1920x1080,
> and the resizer sink should match the ISP source.
>
> With the pipeline improperly setup, the capture fails.
>
> adam
>
>
> > .../bindings/media/rockchip-isp1.yaml | 79 ++++++++++-
> > .../platform/rockchip/rkisp1/rkisp1-capture.c | 102 +++++++++++---
> > .../platform/rockchip/rkisp1/rkisp1-common.h | 32 +++++
> > .../platform/rockchip/rkisp1/rkisp1-debug.c | 14 +-
> > .../platform/rockchip/rkisp1/rkisp1-dev.c | 67 +++++++--
> > .../platform/rockchip/rkisp1/rkisp1-isp.c | 128 +++++++++++++++++-
> > .../platform/rockchip/rkisp1/rkisp1-regs.h | 90 ++++++++++++
> > .../platform/rockchip/rkisp1/rkisp1-resizer.c | 35 ++++-
> > include/uapi/linux/rkisp1-config.h | 2 +
> > 9 files changed, 509 insertions(+), 40 deletions(-)
> >
> > --
> > 2.35.1
> >