Re: [PATCH] PCI/ATS: Allow to enable ATS on VFs even if it is not enabled on PF

From: Ganapatrao Kulkarni
Date: Tue Feb 21 2023 - 04:13:41 EST



Hi Bjorn,

On 16-02-2023 05:06 pm, Ganapatrao Kulkarni wrote:


On 16-02-2023 04:42 pm, Jean-Philippe Brucker wrote:
On Wed, Feb 15, 2023 at 02:57:26PM -0600, Bjorn Helgaas wrote:
[+cc Will, Robin, Joerg for arm-smmu-v3 page size question]

On Sun, Feb 12, 2023 at 08:14:48PM +0200, Leon Romanovsky wrote:
On Wed, Feb 08, 2023 at 10:43:21AM -0800, Ganapatrao Kulkarni wrote:
As per PCIe specification(section 10.5), If a VF implements an
ATS capability, its associated PF must implement an ATS capability.
The ATS Capabilities in VFs and their associated PFs are permitted to
be enabled independently.
Also, it states that the Smallest Translation Unit (STU) for VFs must be
hardwired to Zero and the associated PF's value applies to VFs STU.

The current code allows to enable ATS on VFs only if it is already
enabled on associated PF, which is not necessary as per the specification.

It is only required to have valid STU programmed on PF to enable
ATS on VFs. Adding code to write the first VFs STU to a PF's STU
when PFs ATS is not enabled.

Can you please add here quotes from the spec and its version? I don't see
anything like this in my version of PCIe specification.

See PCIe r6.0, sec 10.5.1.

Signed-off-by: Ganapatrao Kulkarni <gankulkarni@xxxxxxxxxxxxxxxxxxxxxx>
---
  drivers/pci/ats.c | 15 +++++++++++----
  1 file changed, 11 insertions(+), 4 deletions(-)

diff --git a/drivers/pci/ats.c b/drivers/pci/ats.c
index f9cc2e10b676..a97ec67201d1 100644
--- a/drivers/pci/ats.c
+++ b/drivers/pci/ats.c
@@ -67,13 +67,20 @@ int pci_enable_ats(struct pci_dev *dev, int ps)
      if (ps < PCI_ATS_MIN_STU)
          return -EINVAL;
-    /*
-     * Note that enabling ATS on a VF fails unless it's already enabled
-     * with the same STU on the PF.
-     */
      ctrl = PCI_ATS_CTRL_ENABLE;
      if (dev->is_virtfn) {
          pdev = pci_physfn(dev);
+
+        if (!pdev->ats_enabled &&
+                (pdev->ats_stu < PCI_ATS_MIN_STU)) {
+            u16 ctrl2;
+
+            /* Associated PF's STU value applies to VFs. */
+            pdev->ats_stu = ps;
+            ctrl2 = PCI_ATS_CTRL_STU(pdev->ats_stu - PCI_ATS_MIN_STU);
+            pci_write_config_word(pdev, pdev->ats_cap + PCI_ATS_CTRL, ctrl2);
+        }

For reference, it is this way because of edc90fee916b ("PCI: Allocate
ATS struct during enumeration").  The rationale was that since the PF
STU applies to all VFs, we should require that the PF STU be
programmed before enabling ATS on any of the VFs.

This patch relaxes that so the PF STU would be set either by (a)
enabling ATS on the PF or (b) enabling ATS on the first VF.

This looks racy because theoretically drivers for VF A and VF B could
independently call pci_enable_ats() with different IOMMU page sizes,
and we don't know which will get there first.

Most callers supply a compile-time constant (PAGE_SHIFT or
VTD_PAGE_SHIFT), so it won't matter.  arm_smmu_enable_ats() is
fancier, but I *assume* it would still supply the same IOMMU page size
for all VFs of a given PF.

But it's still kind of ugly to call pci_enable_ats(dev_A) and have it
muck with the configuration of dev_B.  Maybe we should configure the
PF STU (without enabling ATS) at enumeration-time in pci_ats_init()?
Is there some way to get the IOMMU page size at that time?

Not really, on Arm the supported page sizes are discovered when probing
the SMMU registers, which may happen later than enumeration, during module
loading.

What this patch is trying to solve is:
* want the PF to bypass SMMU translation, and the VF to undergo SMMU
   translation (in order to assign it to a VM)
* SMMU forbids enabling ATS for a configuration that bypasses translation.
   So the PF ATS capability must be left disabled.

For this situation I wonder if we could do: the SMMU driver, seeing that
the PF is configured to bypass, calls a new function "pci_configure_ats()"

IMO, This seems to be feasible solution for this situation, which addresses SMMU-ATS expectation in bypass and we could avoid PCI VFs race. pci_configure_ats() can be called to program/configure STU of a PF in smmu-bypass mode.


Can we add pci_configure_ats/pci_configure_ats_stu helper?

instead of pci_enable_ats(), which would only set the STU but leave the
cap disabled. Then when setting up translation for the VF, the SMMU driver
calls pci_enable_ats() as usual, which sees the PF's STU set appropriately
and succeeds.

Thanks,
Jean

Thanks,
Ganapat

Thanks,
Ganapat