Re: [PATCH] ARM: dts: allwinner: minimize irq debounce filter per default

From: Andre Przywara
Date: Mon Feb 13 2023 - 06:57:03 EST


On Mon, 13 Feb 2023 10:18:03 +0100
Maxime Ripard <maxime@xxxxxxxxxx> wrote:

Hi,

> On Mon, Feb 13, 2023 at 09:49:55AM +0100, pelzi@xxxxxxxxxxxxxxx wrote:
> > Am 13.02.23 um 09:43 schrieb Maxime Ripard:
> > > On Fri, Feb 10, 2023 at 10:18:14AM +0000, Andre Przywara wrote:
> > > > > > Not sure if you were actually arguing this, but the change I sketched
> > > > > > above (interpreting 0 as 24MHz/1) is separate though, as the current
> > > > > > default is "no DT property", and not 0. There is no input-debounce
> > > > > > property user in the kernel tree at the moment, so we wouldn't break
> > > > > > anyone. The only thing that would change is if a downstream user was
> > > > > > relying on "0" being interpreted as "skip the setup", which isn't
> > > > > > really documented and could be argued to be an implementation detail.
> > > > > >
> > > > > > So I'd suggest to implement 0 as "lowest possible", and documenting that
> > > > > > and the 32KHz/1 default if no property is given.
> > > > > Ah, my bad.
> > > > >
> > > > > There's another thing to consider: there's already a generic per-pin
> > > > > input-debounce property in pinctrl.
> > > > >
> > > > > Since we can't control it per pin but per bank, we moved it to the
> > > > > controller back then, but there's always been this (implicit)
> > > > > expectation that it was behaving the same way.
> > > > >
> > > > > And the generic, per-pin, input-debounce documentation says:
> > > > >
> > > > > > Takes the debounce time in usec as argument or 0 to disable debouncing
> > > > > I agree that silently ignoring it is not great, but interpreting 0 as
> > > > > the lowest possible is breaking that behaviour which, I believe, is a
> > > > > worse outcome.
> > > > Is it really? If I understand the hardware manuals correctly, we cannot
> > > > really turn that feature off, so isn't the lowest possible time period (24
> > > > MHz/1 at the moment) the closest we can get to "turn it off"? So
> > > > implementing this would bring us actually closer to the documented
> > > > behaviour? Or did I get the meaning of this time period wrong?
> > > > At least that's my understanding of how it fixed Andreas' problem: 1µs
> > > > is still not "off", but much better than the 31µs of the default. The new
> > > > 0 would then be 0.041µs.
> > > My point was that the property we share the name (and should share the
> > > semantics with) documents 0 as disabled. We would have a behavior that
> > > doesn't disable it. It's inconsistent.
> > >
> > > The reason doesn't really matter, we would share the same name but have
> > > a completely different behavior, this is super confusing to me.
> >
> > I got the point. As far as I can tell from the datasheet, it is not possible
> > to actually switch off input-debounce. But as a debounce filter is actually
> > a low-pass filter, setting the cut-off frequency as high as possible,
> > appears to be the equivalent to switching it off.
>
> It's not really a matter of hardware here, it's a matter of driver
> behavior vs generic behavior from the framework. The hardware obviously
> influences the former, but it's marginal in that discussion.
>
> As that whole discussion shows, whether the frequency would be high
> enough is application dependent, and thus we cannot just claim that it's
> equivalent in all circumstances.
>
> Making such an assumption will just bite someone else down the road,
> except this time we will have users (you, I'd assume) relying on that
> behavior so we wouldn't be able to address it.
>
> But I also agree with the fact that doing nothing with 0 is bad UX and
> confusing as well.
>
> I still think that we can address both by just erroring out on 0 /
> printing an error message so that it's obvious that we can't support it,
> and we wouldn't change the semantics of the property either.
>
> And then you can set the actual debouncing time you need instead of
> "whatever" in the device tree.

I am on the same page with regards to discouraging 0 as a proper value, and
that we should warn if this is being used.
However I think we should at the same time try to still get as low as
possible when 0 is specified. The debounce property uses microseconds as
the unit, but even the AW hardware allows us to go lower than this. So we
would leave that on the table, somewhat needlessly: input-debounce = <1>
would give us 1333 ns, when the lowest possible is about 42 ns (1/24MHz).

So what about the following:
We document that 0 does not mean off, but tries to get as low as possible.
If the driver sees 0, it issues a warning, but still tries to lower the
debounce period as much as possible, and reports that, like:
[1.2345678] 1c20800.pinctrl: cannot turn off debouncing, setting to 41.7 ns

Alternatively we use a different property name, if that is a concern. We
could then use nanoseconds as a unit value, and then can error out on 0.
Re-using input-debounce is somewhat dodgy anyway, since the generic
property is for a single value only, per pin (in the pinmux DT node, not
in the controller node), whereas we use an array of some non-obvious
subset of ports.

Cheers,
Andre