Re: [PATCH v8 2/3] mfd: axp20x: Add support for AXP313a PMIC

From: Chen-Yu Tsai
Date: Fri Jan 27 2023 - 12:40:55 EST

Next message: Will Deacon: "[GIT PULL] arm64 fix for -rc6"
Previous message: Prabhakar: "[PATCH] arm64: dts: renesas: r9a07g043u: Add Cortex-A55 PMU node"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi,

On Sat, Jan 21, 2023 at 2:45 AM Martin Botka
<martin.botka@xxxxxxxxxxxxxx> wrote:
>
> The AXP313a is a PMIC chip produced by X-Powers, it can be connected via
> an I2C bus.
> The name AXP1530 seems to appear as well, and this is what is used in
> the BSP driver. From all we know it's the same chip, just a different
> name. However we have only seen AXP313a chips in the wild, so go with
> this name.
>
> Compared to the other AXP PMICs it's a rather simple affair: just three
> DCDC converters, three LDOs, and no battery charging support.
>
> Describe the regmap and the MFD bits, along with the registers exposed
> via I2C. Eventually advertise the device using the new compatible
> string.
>
> Signed-off-by: Martin Botka <martin.botka@xxxxxxxxxxxxxx>
> Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
> ---
> drivers/mfd/axp20x-i2c.c | 2 ++
> drivers/mfd/axp20x.c | 61 ++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/axp20x.h | 32 ++++++++++++++++++++
> 3 files changed, 95 insertions(+)
>
> diff --git a/drivers/mfd/axp20x-i2c.c b/drivers/mfd/axp20x-i2c.c
> index f49fbd307958..f061177cb18e 100644
> --- a/drivers/mfd/axp20x-i2c.c
> +++ b/drivers/mfd/axp20x-i2c.c
> @@ -63,6 +63,7 @@ static const struct of_device_id axp20x_i2c_of_match[] = {
> { .compatible = "x-powers,axp209", .data = (void *)AXP209_ID },
> { .compatible = "x-powers,axp221", .data = (void *)AXP221_ID },
> { .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
> + { .compatible = "x-powers,axp313a", .data = (void *)AXP313A_ID},
> { .compatible = "x-powers,axp803", .data = (void *)AXP803_ID },
> { .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
> { },
> @@ -76,6 +77,7 @@ static const struct i2c_device_id axp20x_i2c_id[] = {
> { "axp209", 0 },
> { "axp221", 0 },
> { "axp223", 0 },
> + { "axp313a", 0 },
> { "axp803", 0 },
> { "axp806", 0 },
> { },
> diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
> index 01a6bbb6d266..ff15775f3c27 100644
> --- a/drivers/mfd/axp20x.c
> +++ b/drivers/mfd/axp20x.c
> @@ -39,6 +39,7 @@ static const char * const axp20x_model_names[] = {
> "AXP221",
> "AXP223",
> "AXP288",
> + "AXP313a",
> "AXP803",
> "AXP806",
> "AXP809",
> @@ -154,6 +155,24 @@ static const struct regmap_range axp806_writeable_ranges[] = {
> regmap_reg_range(AXP806_REG_ADDR_EXT, AXP806_REG_ADDR_EXT),
> };
>
> +static const struct regmap_range axp313a_writeable_ranges[] = {
> + regmap_reg_range(AXP313A_ON_INDICATE, AXP313A_IRQ_STATE),
> +};
> +
> +static const struct regmap_range axp313a_volatile_ranges[] = {
> + regmap_reg_range(AXP313A_ON_INDICATE, AXP313A_IRQ_STATE),

Why set the whole range as volatile? Why bother with a cache then?

> +};
> +
> +static const struct regmap_access_table axp313a_writeable_table = {
> + .yes_ranges = axp313a_writeable_ranges,
> + .n_yes_ranges = ARRAY_SIZE(axp313a_writeable_ranges),
> +};
> +
> +static const struct regmap_access_table axp313a_volatile_table = {
> + .yes_ranges = axp313a_volatile_ranges,
> + .n_yes_ranges = ARRAY_SIZE(axp313a_volatile_ranges),
> +};
> +
> static const struct regmap_range axp806_volatile_ranges[] = {
> regmap_reg_range(AXP20X_IRQ1_STATE, AXP20X_IRQ2_STATE),
> };
> @@ -272,6 +291,15 @@ static const struct regmap_config axp288_regmap_config = {
> .cache_type = REGCACHE_RBTREE,
> };
>
> +static const struct regmap_config axp313a_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .wr_table = &axp313a_writeable_table,
> + .volatile_table = &axp313a_volatile_table,
> + .max_register = AXP313A_IRQ_STATE,
> + .cache_type = REGCACHE_RBTREE,
> +};
> +
> static const struct regmap_config axp806_regmap_config = {
> .reg_bits = 8,
> .val_bits = 8,
> @@ -415,6 +443,16 @@ static const struct regmap_irq axp288_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1),
> };
>
> +static const struct regmap_irq axp313a_regmap_irqs[] = {
> + INIT_REGMAP_IRQ(AXP313A, PEK_RIS_EDGE, 0, 7),
> + INIT_REGMAP_IRQ(AXP313A, PEK_FAL_EDGE, 0, 6),
> + INIT_REGMAP_IRQ(AXP313A, PEK_SHORT, 0, 5),
> + INIT_REGMAP_IRQ(AXP313A, PEK_LONG, 0, 4),
> + INIT_REGMAP_IRQ(AXP313A, DCDC3_V_LOW, 0, 3),
> + INIT_REGMAP_IRQ(AXP313A, DCDC2_V_LOW, 0, 2),
> + INIT_REGMAP_IRQ(AXP313A, DIE_TEMP_HIGH, 0, 0),
> +};
> +
> static const struct regmap_irq axp803_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP803, ACIN_OVER_V, 0, 7),
> INIT_REGMAP_IRQ(AXP803, ACIN_PLUGIN, 0, 6),
> @@ -548,6 +586,17 @@ static const struct regmap_irq_chip axp288_regmap_irq_chip = {
>
> };
>
> +static const struct regmap_irq_chip axp313a_regmap_irq_chip = {
> + .name = "axp313a_irq_chip",
> + .status_base = AXP313A_IRQ_STATE,
> + .ack_base = AXP313A_IRQ_STATE,
> + .unmask_base = AXP313A_IRQ_EN,
> + .init_ack_masked = true,
> + .irqs = axp313a_regmap_irqs,
> + .num_irqs = ARRAY_SIZE(axp313a_regmap_irqs),
> + .num_regs = 1,
> +};
> +
> static const struct regmap_irq_chip axp803_regmap_irq_chip = {
> .name = "axp803",
> .status_base = AXP20X_IRQ1_STATE,
> @@ -676,6 +725,12 @@ static const struct mfd_cell axp152_cells[] = {
> },
> };
>
> +static struct mfd_cell axp313a_cells[] = {
> + {
> + .name = "axp20x-regulator",

Lee asked for MFD_CELL_NAME() in v7 here.

Could you also add the power button cell? This would make it an actual
MFD, and also complete, since that is the only other function this
PMIC has. Or at least add a note mentioning it. Implementing it will
require a device that actually routes that pin out. AFAICT the MangoPi
doesn't.

> + },
> +};
> +
> static const struct resource axp288_adc_resources[] = {
> DEFINE_RES_IRQ_NAMED(AXP288_IRQ_GPADC, "GPADC"),
> };
> @@ -892,6 +947,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
> axp20x->regmap_irq_chip = &axp288_regmap_irq_chip;
> axp20x->irq_flags = IRQF_TRIGGER_LOW;
> break;
> + case AXP313A_ID:
> + axp20x->nr_cells = ARRAY_SIZE(axp313a_cells);
> + axp20x->cells = axp313a_cells;
> + axp20x->regmap_cfg = &axp313a_regmap_config;
> + axp20x->regmap_irq_chip = &axp313a_regmap_irq_chip;
> + break;
> case AXP803_ID:
> axp20x->nr_cells = ARRAY_SIZE(axp803_cells);
> axp20x->cells = axp803_cells;
> diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
> index 2058194807bd..12e4fc3e8391 100644
> --- a/include/linux/mfd/axp20x.h
> +++ b/include/linux/mfd/axp20x.h
> @@ -17,6 +17,7 @@ enum axp20x_variants {
> AXP221_ID,
> AXP223_ID,
> AXP288_ID,
> + AXP313A_ID,
> AXP803_ID,
> AXP806_ID,
> AXP809_ID,
> @@ -91,6 +92,17 @@ enum axp20x_variants {
> #define AXP22X_ALDO3_V_OUT 0x2a
> #define AXP22X_CHRG_CTRL3 0x35
>
> +#define AXP313A_ON_INDICATE 0x00
> +#define AXP313A_OUTPUT_CONTROL 0x10
> +#define AXP313A_DCDC1_CONRTOL 0x13
> +#define AXP313A_DCDC2_CONRTOL 0x14
> +#define AXP313A_DCDC3_CONRTOL 0x15
> +#define AXP313A_ALDO1_CONRTOL 0x16
> +#define AXP313A_DLDO1_CONRTOL 0x17

Please also add register 0x1a (note, some bits of this are volatile)
and implement power off with bit 7. The current axp_power_off()
function will not work for this PMIC.

This PMIC also supports software-triggered reset with bit 6 in the same
register. This function would be nice to have, however there's no related
code in the mfd driver right now, since IIRC none of the other ones had
this.

> +#define AXP313A_OUTPUT_MONITOR 0x1d

Not sure why you need this?

> +#define AXP313A_IRQ_EN 0x20
> +#define AXP313A_IRQ_STATE 0x21
> +
> #define AXP806_STARTUP_SRC 0x00
> #define AXP806_CHIP_ID 0x03
> #define AXP806_PWR_OUT_CTRL1 0x10
> @@ -322,6 +334,16 @@ enum {
> AXP22X_REG_ID_MAX,
> };
>
> +enum {
> + AXP313A_DCDC1 = 0,
> + AXP313A_DCDC2,
> + AXP313A_DCDC3,
> + AXP313A_LDO1,

This is called ALDO1 in the datasheet ...

> + AXP313A_LDO2,

... and this one DLDO1.

You already have the registers named that way, so you might as well
fix the names here as well.

Thanks
ChenYu

> + AXP313A_RTC_LDO,
> + AXP313A_REG_ID_MAX,
> +};
> +
> enum {
> AXP806_DCDCA = 0,
> AXP806_DCDCB,
> @@ -548,6 +570,16 @@ enum axp288_irqs {
> AXP288_IRQ_BC_USB_CHNG,
> };
>
> +enum axp313a_irqs {
> + AXP313A_IRQ_DIE_TEMP_HIGH,
> + AXP313A_IRQ_DCDC2_V_LOW = 2,
> + AXP313A_IRQ_DCDC3_V_LOW,
> + AXP313A_IRQ_PEK_LONG,
> + AXP313A_IRQ_PEK_SHORT,
> + AXP313A_IRQ_PEK_FAL_EDGE,
> + AXP313A_IRQ_PEK_RIS_EDGE,
> +};
> +
> enum axp803_irqs {
> AXP803_IRQ_ACIN_OVER_V = 1,
> AXP803_IRQ_ACIN_PLUGIN,
> --
> 2.39.0
>

Next message: Will Deacon: "[GIT PULL] arm64 fix for -rc6"
Previous message: Prabhakar: "[PATCH] arm64: dts: renesas: r9a07g043u: Add Cortex-A55 PMU node"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]