Re: [PATCH 2/2] arm64: dts: meson: add support for Radxa Zero2

[Krzysztof Kozlowski]

On 27/01/2023 12:09, Christian Hewitt wrote:
> From: Yuntian Zhang <yt@xxxxxxxxx>
> 
> Radxa Zero2 is a small form factor SBC based on the Amlogic A311D
> chipset that ships in a number of eMMC configurations:
> 

Thank you for your patch. There is something to discuss/improve.

> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> +		clocks = <&wifi32k>;
> +		clock-names = "ext_clock";
> +	};
> +
> +	ao_5v: regulator-ao_5v {


No underscores in node names.

> +		compatible = "regulator-fixed";
> +		regulator-name = "AO_5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +
> +	vcc_1v8: regulator-vcc_1v8 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC_1V8";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vcc_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	vcc_3v3: regulator-vcc_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +		/* FIXME: actually controlled by VDDCPU_B_EN */
> +	};
> +
> +	vddao_1v8: regulator-vddao_1v8 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_AO1V8";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	vddao_3v3: regulator-vddao_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDAO_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&ao_5v>;
> +		regulator-always-on;
> +	};
> +
> +	vddcpu_a: regulator-vddcpu-a {
> +		/*
> +		 * MP8756GD Regulator.
> +		 */
> +		compatible = "pwm-regulator";
> +
> +		regulator-name = "VDDCPU_A";
> +		regulator-min-microvolt = <730000>;
> +		regulator-max-microvolt = <1022000>;
> +
> +		pwm-supply = <&ao_5v>;
> +
> +		pwms = <&pwm_ab 0 1250 0>;
> +		pwm-dutycycle-range = <100 0>;
> +
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	vddcpu_b: regulator-vddcpu-b {
> +		/*
> +		 * Silergy SY8120B1ABC Regulator.
> +		 */
> +		compatible = "pwm-regulator";
> +
> +		regulator-name = "VDDCPU_B";
> +		regulator-min-microvolt = <730000>;
> +		regulator-max-microvolt = <1022000>;
> +
> +		pwm-supply = <&ao_5v>;
> +
> +		pwms = <&pwm_AO_cd 1 1250 0>;
> +		pwm-dutycycle-range = <100 0>;
> +
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	sound {
> +		compatible = "amlogic,axg-sound-card";
> +		model = "RADXA-ZERO2";
> +		audio-aux-devs = <&tdmout_b>;
> +		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
> +				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
> +				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
> +				"TDM_B Playback", "TDMOUT_B OUT";
> +
> +		assigned-clocks = <&clkc CLKID_MPLL2>,
> +				  <&clkc CLKID_MPLL0>,
> +				  <&clkc CLKID_MPLL1>;
> +		assigned-clock-parents = <0>, <0>, <0>;
> +		assigned-clock-rates = <294912000>,
> +				       <270950400>,
> +				       <393216000>;
> +
> +		dai-link-0 {
> +			sound-dai = <&frddr_a>;
> +		};
> +
> +		dai-link-1 {
> +			sound-dai = <&frddr_b>;
> +		};
> +
> +		dai-link-2 {
> +			sound-dai = <&frddr_c>;
> +		};
> +
> +		/* 8ch hdmi interface */
> +		dai-link-3 {
> +			sound-dai = <&tdmif_b>;
> +			dai-format = "i2s";
> +			dai-tdm-slot-tx-mask-0 = <1 1>;
> +			dai-tdm-slot-tx-mask-1 = <1 1>;
> +			dai-tdm-slot-tx-mask-2 = <1 1>;
> +			dai-tdm-slot-tx-mask-3 = <1 1>;
> +			mclk-fs = <256>;
> +
> +			codec {
> +				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
> +			};
> +		};
> +
> +		/* hdmi glue */
> +		dai-link-4 {
> +			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
> +
> +			codec {
> +				sound-dai = <&hdmi_tx>;
> +			};
> +		};
> +	};
> +
> +	wifi32k: wifi32k {

Generic node names, so clock-0 or clock-xyz



Best regards,
Krzysztof