Re: [PATCH 2/2] arm64: dts: qcom: sa8540p-ride: Document i2c busses

[Shazad Hussain]

On 1/25/2023 12:53 AM, Andrew Halaney wrote:
> It isn't obvious in the current devicetree what is connected. Go ahead
> and document what's on the other end.
>
> Signed-off-by: Andrew Halaney <ahalaney@xxxxxxxxxx>
> ---
>
> Not sure if this sort of patch is actually welcomed or not but I went
> through this exercise (for the prior patch) and thought it might be
> useful to document.
>
> Shazad, this also highlights (unless I misread things) that i2c12 has no
> use for us, right? If agreed I can remove it but sorting through the
> lore links that provided all this it seems like at the time it was
> desired to be added.

Andrew, i2c12 has GPU PWR ctl use case, so let's keep it enabled.

-Shazad

> Thanks,
> Andrew
>
>   arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 5 +++++
>   1 file changed, 5 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> index cb9fbdeb5a9e..3478ab91fe73 100644
> --- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> @@ -317,6 +317,7 @@ &xo_board_clk {
>   
>   &tlmm {
>   	i2c0_default: i2c0-default-state {
> +		/* To USB7002T-I/KDXVA0 USB hub (SIP1 only) */
>   		pins = "gpio135", "gpio136";
>   		function = "qup0";
>   		drive-strength = <2>;
> @@ -324,6 +325,7 @@ i2c0_default: i2c0-default-state {
>   	};
>   
>   	i2c1_default: i2c1-default-state {
> +		/* To PM40028B-F3EI PCIe switch */
>   		pins = "gpio158", "gpio159";
>   		function = "qup1";
>   		drive-strength = <2>;
> @@ -331,6 +333,7 @@ i2c1_default: i2c1-default-state {
>   	};
>   
>   	i2c12_default: i2c12-default-state {
> +		/* Not connected */
>   		pins = "gpio0", "gpio1";
>   		function = "qup12";
>   		drive-strength = <2>;
> @@ -338,6 +341,7 @@ i2c12_default: i2c12-default-state {
>   	};
>   
>   	i2c15_default: i2c15-default-state {
> +		/* To display connector (SIP1 only) */
>   		pins = "gpio36", "gpio37";
>   		function = "qup15";
>   		drive-strength = <2>;
> @@ -345,6 +349,7 @@ i2c15_default: i2c15-default-state {
>   	};
>   
>   	i2c18_default: i2c18-default-state {
> +		/* To ASM330LHH IMU (SIP1 only) */
>   		pins = "gpio66", "gpio67";
>   		function = "qup18";
>   		drive-strength = <2>;