Re: [PATCH v2 2/8] arm64: dts: qcom: sc7280: audioreach: Add sound node

[Srinivasa Rao Mandadapu]

On 1/10/2023 4:30 PM, Krzysztof Kozlowski wrote:
Thanks for your time Krzysztof!!!
> On 05/01/2023 14:37, Srinivasa Rao Mandadapu wrote:
> > Add sound node for sc7280 based audioreach platforms.
> >
> > Include audioreach dtsi into crd-rev3 platform specific dts file.
> > Also remove phandle to sound node, as audio routing is same as
> > audioreach specific dtsi file.
> Thank you for your patch. There is something to discuss/improve.
>
> > +#include <dt-bindings/sound/qcom,q6afe.h>
> > +
> > +/{
> > +	/* BOARD-SPECIFIC TOP LEVEL NODES */
> > +	sound: sound {
> > +		compatible = "google,sc7280-herobrine";
> > +		model = "SC7280-AUDIOREACH";
> > +		adsp-mode;
> There is no such property. Test DTS against your schema, so make
> dtbs_check DT_SCHEMA_FILES=google,sc7280-herobrine
Okay. Will fix it.
> > +		audio-routing =
> > +			"IN1_HPHL", "HPHL_OUT",
> > +			"IN2_HPHR", "HPHR_OUT",
> > +			"AMIC1", "MIC BIAS1",
> > +			"AMIC2", "MIC BIAS2",
> > +			"VA DMIC0", "MIC BIAS1",
> > +			"VA DMIC1", "MIC BIAS1",
> > +			"VA DMIC2", "MIC BIAS3",
> > +			"VA DMIC3", "MIC BIAS3",
> > +			"TX SWR_ADC0", "ADC1_OUTPUT",
> > +			"TX SWR_ADC1", "ADC2_OUTPUT",
> > +			"TX SWR_ADC2", "ADC3_OUTPUT",
> > +			"TX SWR_DMIC0", "DMIC1_OUTPUT",
> > +			"TX SWR_DMIC1", "DMIC2_OUTPUT",
> > +			"TX SWR_DMIC2", "DMIC3_OUTPUT",
> > +			"TX SWR_DMIC3", "DMIC4_OUTPUT",
> > +			"TX SWR_DMIC4", "DMIC5_OUTPUT",
> > +			"TX SWR_DMIC5", "DMIC6_OUTPUT",
> > +			"TX SWR_DMIC6", "DMIC7_OUTPUT",
> > +			"TX SWR_DMIC7", "DMIC8_OUTPUT";
> > +
> > +		qcom,msm-mbhc-hphl-swh = <1>;
> > +		qcom,msm-mbhc-gnd-swh = <1>;
> > +
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		#sound-dai-cells = <0>;
> > +
> > +		dai-link@0 {
> > +			link-name = "WCD9385 Playback";
> > +			reg = <0>;
> > +
> > +			cpu {
> > +				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
> > +			};
> > +			codec {
> > +				sound-dai = <&wcd9385 0>, <&swr0 0>, <&lpass_rx_macro 0>;
> > +			};
> > +			platform {
> > +				sound-dai = <&q6apm>;
> > +			};
> > +		};
> > +
> > +		dai-link@1 {
> > +			link-name = "WCD9385 Capture";
> > +			reg = <1>;
> > +
> > +			cpu {
> > +				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
> > +			};
> > +			codec {
> > +				sound-dai = <&wcd9385 1>, <&swr1 0>, <&lpass_tx_macro 0>;
> > +			};
> > +			platform {
> > +				sound-dai = <&q6apm>;
> > +			};
> > +		};
> > +
> > +		dai-link@2 {
> > +			link-name = "Amplifier Playback";
> > +			reg = <3>;
> Missing dtbs W=1 build.
Okay. Will fix it.
> > +
> > +			cpu {
> > +				sound-dai = <&q6apmbedai SECONDARY_MI2S_RX>;
> > +			};
> > +
> Use consistent style. Either blank line or not between the
> cpu/codec/platform nodes.
Okay. will fix it.
> > +			codec {
> > +				sound-dai = <&max98360a>;
> > +			};
> > +
> > +			platform {
> > +				sound-dai = <&q6apm>;
> > +			};
> > +		};
> > +
> > +		dai-link@3 {
> > +			link-name = "DMIC";
> > +			reg = <4>;
> Same problem, wrong reg.
Okay.
> > +
> > +			cpu {
> > +				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
> > +			};
> > +
> > +			codec {
> > +				sound-dai = <&lpass_va_macro 0>;
> > +			};
> > +
> > +			platform {
> > +				sound-dai = <&q6apm>;
> > +			};
> > +		};
> > +	};
> > +};
> Best regards,
> Krzysztof